Slide 1
... • Mesh: More popular as voltage sources do exist physically. • Nodal: Less popular as current sources do not exist physically except in models of electronics circuits. ...
... • Mesh: More popular as voltage sources do exist physically. • Nodal: Less popular as current sources do not exist physically except in models of electronics circuits. ...
AMC6821 E2E Question
... still run properly even after I2C communication is terminated. Any help would be greatly appreciated. ...
... still run properly even after I2C communication is terminated. Any help would be greatly appreciated. ...
Electronics
... the fuse is working and the LED lights up. The H bridge stepper motor control circuit uses 8 transistors to control the current through both phases of the stepper motor. The current must be fed to the stepper motor in the correct sequence in order for it to run forwards and backwards. A microcontrol ...
... the fuse is working and the LED lights up. The H bridge stepper motor control circuit uses 8 transistors to control the current through both phases of the stepper motor. The current must be fed to the stepper motor in the correct sequence in order for it to run forwards and backwards. A microcontrol ...
MAX1575 White LED 1x/1.5x Charge Pump for Main and Sub-Displays General Description
... high, the LED current initially goes to ILED_. Dimming for the main display is done by pulsing ENM low (500ns to 500µs pulse width). Dimming for the subdisplay is done by pulsing ENS low (500ns to 500µs pulse width). Each pulse reduces the LED current by 10%, so after one pulse the LED current is 0. ...
... high, the LED current initially goes to ILED_. Dimming for the main display is done by pulsing ENM low (500ns to 500µs pulse width). Dimming for the subdisplay is done by pulsing ENS low (500ns to 500µs pulse width). Each pulse reduces the LED current by 10%, so after one pulse the LED current is 0. ...
Harmonic analysis of LED street lighting according to
... • Arc welding equipment which is not professional equipment Class C • Lighting equipment over 25 W including dimming devices Class D • Equipment having an active power of less than or equal to 600W and is either a PC or PC monitor, or a television. The harmonic current limit for class C equipment is ...
... • Arc welding equipment which is not professional equipment Class C • Lighting equipment over 25 W including dimming devices Class D • Equipment having an active power of less than or equal to 600W and is either a PC or PC monitor, or a television. The harmonic current limit for class C equipment is ...
DU28120T RF Power MOSFET Transistor 120W, 2-175MHz, 28V
... PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. E ...
... PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. E ...
TT-203 Remote Control
... 7. Replace the switch cover making sure no wires are trapped between the switch plate and the wall. Do not over tighten the switch plate as this could crack or distort the switch. ...
... 7. Replace the switch cover making sure no wires are trapped between the switch plate and the wall. Do not over tighten the switch plate as this could crack or distort the switch. ...
COMBOLIGHT New Construction Recessed w/ Trim - 12V MR16 - 3 Light
... conductors or 60º C for end of run. The fixture is also UL listed as ‘access above ceiling not required’. D.... Electrical Electrical accessible through ceiling opening. J-Box located on the side wall of the housing behind removable access doors. Integral electronic or magnetic low voltage transform ...
... conductors or 60º C for end of run. The fixture is also UL listed as ‘access above ceiling not required’. D.... Electrical Electrical accessible through ceiling opening. J-Box located on the side wall of the housing behind removable access doors. Integral electronic or magnetic low voltage transform ...
... is varied in proportion to the amplitude of a sine wave evaluated at the centre of the same pulse. The distortion factor and lower order harmonics are reduced significantly. The gating signals are generated by comparing a sinusoidal reference signal with a triangular carrier wave of frequency Fc.The ...
PC Power Supply Repair
... other components in the chain from harm. If the resistor is burned beyond recognition, you can replace it with any 1/4-watt resistor with a value of 1 to 10 ohms (the exact value isn’t important). Sometimes, though, even the fusible isn’t fast enough to prevent damage. So before installing the new p ...
... other components in the chain from harm. If the resistor is burned beyond recognition, you can replace it with any 1/4-watt resistor with a value of 1 to 10 ohms (the exact value isn’t important). Sometimes, though, even the fusible isn’t fast enough to prevent damage. So before installing the new p ...
COMBOLIGHT New Construction Recessed w/ Trim - 12V MR16 - 2 Light
... conductors or 60º C for end of run. The fixture is also UL listed as ‘access above ceiling not required’. ...
... conductors or 60º C for end of run. The fixture is also UL listed as ‘access above ceiling not required’. ...
RF5745 2.4GHz TO 2.5GHz, 802.11b/g/n SINGLE-BAND FRONT END MODULE Features
... The RF5745 is an integrated front-end module (FEM) for high performance ZigBee® (802.15.4) and WiFi (802.11b/g) applications in the 2.4GHz to 2.5GHz ISM band. The FEM addresses the need for aggressive size reduction by integrating 50 matching networks to all RF ports and minimizing the number of ex ...
... The RF5745 is an integrated front-end module (FEM) for high performance ZigBee® (802.15.4) and WiFi (802.11b/g) applications in the 2.4GHz to 2.5GHz ISM band. The FEM addresses the need for aggressive size reduction by integrating 50 matching networks to all RF ports and minimizing the number of ex ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.