![ADP2116 Configurable, Dual 3 A/Single 6 A, Synchronous, Step-Down DC-to-DC Regulator](http://s1.studyres.com/store/data/008895214_1-bc20cc835d9edb670e8e7cd662a9da24-300x300.png)
Some Aspects of the Balun Problem
... no. 73 beads (µ = 2500 to 4000) over a piece of RG-303 coaxial cable. The impedance of the outer conductor of the cable measured 4500 + j3800 ohms at 4.0 MHz; 15.6 + j13.1 was measured using a single bead. For practical baluns to be used from 1.8 to 30 MHz (less than 12 inches long, including connec ...
... no. 73 beads (µ = 2500 to 4000) over a piece of RG-303 coaxial cable. The impedance of the outer conductor of the cable measured 4500 + j3800 ohms at 4.0 MHz; 15.6 + j13.1 was measured using a single bead. For practical baluns to be used from 1.8 to 30 MHz (less than 12 inches long, including connec ...
Atmel ATtiny45 Appendix A - ATtiny45 Automotive specification at 150°C Description PRELIMINARY DATASHEET
... 3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions (non-transient), the following must be observed: 1] The sum of all IOL, for all ports, should not exceed 400mA. 2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA. 3] The ...
... 3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions (non-transient), the following must be observed: 1] The sum of all IOL, for all ports, should not exceed 400mA. 2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA. 3] The ...
AN123 - Linear Technology
... injection and recover before the next switch movement to minimize signal degradation. In the ADC driver, this implies good transient response and wide bandwidth relative to the ADC’s sampling frequency. ...
... injection and recover before the next switch movement to minimize signal degradation. In the ADC driver, this implies good transient response and wide bandwidth relative to the ADC’s sampling frequency. ...
LT3759 - Wide Input Voltage Range Boost/SEPIC/Inverting Controller
... The LT3759 uses a fixed frequency, current mode control scheme to provide excellent line and load regulation. Operation can be best understood by referring to the Block Diagram in Figure 1. The start of each oscillator cycle sets the SR latch (SR1) and turns on the external power MOSFET switch M1 th ...
... The LT3759 uses a fixed frequency, current mode control scheme to provide excellent line and load regulation. Operation can be best understood by referring to the Block Diagram in Figure 1. The start of each oscillator cycle sets the SR latch (SR1) and turns on the external power MOSFET switch M1 th ...
Ten
... answers are as numerous as the systems in which they are installed. The following pages discuss ten different individual technical characteristics of the Bulk Metal® Foil technology that are important to precision analog circuits. While each characteristic is discussed independently for clarity, man ...
... answers are as numerous as the systems in which they are installed. The following pages discuss ten different individual technical characteristics of the Bulk Metal® Foil technology that are important to precision analog circuits. While each characteristic is discussed independently for clarity, man ...
12 V +12 V +12 V
... One of these output voltage readings is anomalous. In other words, it does not appear to be ”correct”. This is very strange, because these figures are real measurements and not predictions! Perplexed, the student approaches the instructor and asks for help. The instructor sees the anomalous voltage ...
... One of these output voltage readings is anomalous. In other words, it does not appear to be ”correct”. This is very strange, because these figures are real measurements and not predictions! Perplexed, the student approaches the instructor and asks for help. The instructor sees the anomalous voltage ...
BD9488F : LED / LCD Drivers
... The OVP terminal is the input for over-voltage protection and short circuit protection of output voltage. As OVP is more than 3.0V, the over-voltage protection (OVP) will work. At the moment of this detection, the BD9488 stops the switching of the output GATE and starts to count up the abnormal inte ...
... The OVP terminal is the input for over-voltage protection and short circuit protection of output voltage. As OVP is more than 3.0V, the over-voltage protection (OVP) will work. At the moment of this detection, the BD9488 stops the switching of the output GATE and starts to count up the abnormal inte ...
ADM1270 - Analog Devices
... Positive Current Sense Input Pin (SENSE+). This pin connects to the main supply input. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). ...
... Positive Current Sense Input Pin (SENSE+). This pin connects to the main supply input. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). ...
Document
... Stress that no papers can be attached to the lab notebook. Everything has to be cut and glued to the lab notebook. c) Missed Lab / Late Policy: Labs are due exactly one week from the start of class. Labs can be handed in early, but must be turned into one of the 210 GSI's or Professor's which should ...
... Stress that no papers can be attached to the lab notebook. Everything has to be cut and glued to the lab notebook. c) Missed Lab / Late Policy: Labs are due exactly one week from the start of class. Labs can be handed in early, but must be turned into one of the 210 GSI's or Professor's which should ...
TRANSMISSION LINES
... Typical examples of such structures are transmission lines and waveguides. Waveguides are discussed in the next chapter; transmission lines are considered in this chapter. Transmission lines are commonly used in power distribution (at low frequencies) and in communications (at high frequencies). Var ...
... Typical examples of such structures are transmission lines and waveguides. Waveguides are discussed in the next chapter; transmission lines are considered in this chapter. Transmission lines are commonly used in power distribution (at low frequencies) and in communications (at high frequencies). Var ...
4 Series Circuits
... Air Washington Electronics – Direct Current The fact that the same current flows through each component of a series circuit can be verified by inserting meters into the circuit at various points, as shown in Circuit 1. If this were done, each meter would be found to indicate the same value of curre ...
... Air Washington Electronics – Direct Current The fact that the same current flows through each component of a series circuit can be verified by inserting meters into the circuit at various points, as shown in Circuit 1. If this were done, each meter would be found to indicate the same value of curre ...
Exercises on Static Circuits
... the resistor. A component that can safely dissipate a large power (e.g., 1W) will cost more and be larger than one that handles a smaller power (say, 1/8W), so it’s desirable to find the smallest safe power-rating for a component. (b) Now we consider the conditions under which vL = vz (which you ass ...
... the resistor. A component that can safely dissipate a large power (e.g., 1W) will cost more and be larger than one that handles a smaller power (say, 1/8W), so it’s desirable to find the smallest safe power-rating for a component. (b) Now we consider the conditions under which vL = vz (which you ass ...
using the acom2 adapter with motorola microcontrollers in
... LOGIC LEVELS AND PIN VOLTAGES - HOW THE MICROCONTROLLER PERFORMS THE MODE TEST A logic level is simply a voltage which represents a logic 1 or a logic 0. These voltages are the same as the power supply of the microcontroller where a logic 0 is 0 volts or ground (GND) and a logic 1 is between 3 and 5 ...
... LOGIC LEVELS AND PIN VOLTAGES - HOW THE MICROCONTROLLER PERFORMS THE MODE TEST A logic level is simply a voltage which represents a logic 1 or a logic 0. These voltages are the same as the power supply of the microcontroller where a logic 0 is 0 volts or ground (GND) and a logic 1 is between 3 and 5 ...
a treatment of differential signaling and its design
... logic levels is compromised. This ability to “ignore” ground offsets has been the backbone of the wired Internet from the onset. In the case of Ethernet, the two ends of these links are transformer coupled. (I have seen examples of Ethernet links where the ground offset voltage was more than 6.5VAC ...
... logic levels is compromised. This ability to “ignore” ground offsets has been the backbone of the wired Internet from the onset. In the case of Ethernet, the two ends of these links are transformer coupled. (I have seen examples of Ethernet links where the ground offset voltage was more than 6.5VAC ...
Test probe
A test probe (test lead, test prod, or scope probe) is a physical device used to connect electronic test equipment to a device under test (DUT). They range from very simple, robust devices to complex probes that are sophisticated, expensive, and fragile.