P S C
... 8. Purpose: Analyze a commercial AC adapter by reverse engineering. Output Observations: Obtain a cheap AC adapter – not a PC power supply, a really cheap one such as those used to run an inexpensive tape recorder or similar. a) Observe its output voltage using an oscilloscope. b) As a load, connect ...
... 8. Purpose: Analyze a commercial AC adapter by reverse engineering. Output Observations: Obtain a cheap AC adapter – not a PC power supply, a really cheap one such as those used to run an inexpensive tape recorder or similar. a) Observe its output voltage using an oscilloscope. b) As a load, connect ...
AC/Synchro/Resolver/Phase Definitions
... measurement. To insure accurate measurement, the noise must be attenuated such that an acceptable Signal-to-Noise ratio can be maintained. Null Spacing Error: Expressed in minutes, it is a measure of departure from predefined intervals where the electrical null should mechanically appear. For exampl ...
... measurement. To insure accurate measurement, the noise must be attenuated such that an acceptable Signal-to-Noise ratio can be maintained. Null Spacing Error: Expressed in minutes, it is a measure of departure from predefined intervals where the electrical null should mechanically appear. For exampl ...
Equivalent Circuit Modeling in EIS
... incorporating the elements mentioned above. The behavior of each element is then described in terms of “classical” electrical components (resistors, capacitors, ...
... incorporating the elements mentioned above. The behavior of each element is then described in terms of “classical” electrical components (resistors, capacitors, ...
For Full Text Click Here
... multiple discontinuity points in a circuit (which means different time delays) with different coefficients. These discontinuity points and corresponding reflection coefficients can be identified from the reflected voltage waveform by taking the correlation of the reflected voltage with the incident ...
... multiple discontinuity points in a circuit (which means different time delays) with different coefficients. These discontinuity points and corresponding reflection coefficients can be identified from the reflected voltage waveform by taking the correlation of the reflected voltage with the incident ...
TETRA-POLAR BIOELECTRICAL IMPEDANCE ANALYZER
... and V equals AL. Although the body is not a uniform cylinder and its conductivity is not constant, an empirical relationship can be established between the impedance quotient (length2/R) and the volume of water, which contains electrolytes that conduct the electrical current through the body. In pra ...
... and V equals AL. Although the body is not a uniform cylinder and its conductivity is not constant, an empirical relationship can be established between the impedance quotient (length2/R) and the volume of water, which contains electrolytes that conduct the electrical current through the body. In pra ...
PDF
... Wavelet Transform (WT) is an efficient means of analyzing transient currents and voltages. Unlike DFT, WT not only analyzes the signal in frequency bands but also provides non-uniform division of frequency domain, i.e. WT uses short window at high frequencies and long window at low frequencies. This ...
... Wavelet Transform (WT) is an efficient means of analyzing transient currents and voltages. Unlike DFT, WT not only analyzes the signal in frequency bands but also provides non-uniform division of frequency domain, i.e. WT uses short window at high frequencies and long window at low frequencies. This ...
RevF_088e
... Note: 25 ohms (50 ohm in parallel with 50 ohms) and 1 uF gives a 6.37 kHz - 3dB point if we bandwidth limit the current probe. Airbus does not want to bandwidth limit the current probe. Jean-Paul needs the first msec to be controlled for SSPCs. Note: Mario suggests a different standardization of the ...
... Note: 25 ohms (50 ohm in parallel with 50 ohms) and 1 uF gives a 6.37 kHz - 3dB point if we bandwidth limit the current probe. Airbus does not want to bandwidth limit the current probe. Jean-Paul needs the first msec to be controlled for SSPCs. Note: Mario suggests a different standardization of the ...
Electrochemical Impedance Spectroscopy Primer
... are separated from ions charges. The separation is very small, often on the order of angstroms. Charges separated by an insulator form a capacitor. On a bare metal immersed in an electrolyte, you can estimate that there will be 20 to 60 µF of capacitance for every cm2 of electrode area. The value of ...
... are separated from ions charges. The separation is very small, often on the order of angstroms. Charges separated by an insulator form a capacitor. On a bare metal immersed in an electrolyte, you can estimate that there will be 20 to 60 µF of capacitance for every cm2 of electrode area. The value of ...
Standing wave ratio
In radio engineering and telecommunications, standing wave ratio (SWR) is a measure of impedance matching of loads to the characteristic impedance of a transmission line or waveguide. Impedance mismatches result in standing waves along the transmission line, and SWR is defined as the ratio of the partial standing wave's amplitude at an antinode (maximum) to the amplitude at a node (minimum) along the line.The SWR is usually thought of in terms of the maximum and minimum AC voltages along the transmission line, thus called the voltage standing wave ratio or VSWR (sometimes pronounced ""viswar""). For example, the VSWR value 1.2:1 denotes an AC voltage due to standing waves along the transmission line reaching a peak value 1.2 times that of the minimum AC voltage along that line. The SWR can as well be defined as the ratio of the maximum amplitude to minimum amplitude of the transmission line's currents, electric field strength, or the magnetic field strength. Neglecting transmission line loss, these ratios are identical.The power standing wave ratio (PSWR) is defined as the square of the VSWR, however this terminology has no physical relation to actual powers involved in transmission.The SWR can be measured with an instrument called an SWR meter. Since SWR is defined relative to the transmission line's characteristic impedance, the SWR meter must be constructed for that impedance; in practice most transmission lines used in these applications are coaxial cables with an impedance of either 50 or 75 ohms. Checking the SWR is a standard procedure in a radio station, for instance, to verify impedance matching of the antenna to the transmission line (and transmitter). Unlike connecting an impedance analyzer (or ""impedance bridge"") directly to the antenna (or other load), the SWR does not measure the actual impedance of the load, but quantifies the magnitude of the impedance mismatch just performing a measurement on the transmitter side of the transmission line.