simplified block diagram
... The TS8388BFS is an 8 bit 1GSPS ADC based on an advanced high speed bipolar technology featuring a cutoff frequency of 25 GHz. The TS8388BFS includes a front-end master/slave Track and Hold stage (S/H), followed by an analog encoding stage and interpolation circuitry. Successive banks of ...
... The TS8388BFS is an 8 bit 1GSPS ADC based on an advanced high speed bipolar technology featuring a cutoff frequency of 25 GHz. The TS8388BFS includes a front-end master/slave Track and Hold stage (S/H), followed by an analog encoding stage and interpolation circuitry. Successive banks of ...
EFFICIENT FPGA IMPLEMENTATION OF PWM CORE
... • The VHDL model was implemented on XC4003E and optimized for area. • The data value is loaded by the user using switches connected to the input pins of the XC4003E. • The optimized implementation was found to consume 33 flip-flops on the CLBs, i.e., 16% of the total available flip-flops. • Impleme ...
... • The VHDL model was implemented on XC4003E and optimized for area. • The data value is loaded by the user using switches connected to the input pins of the XC4003E. • The optimized implementation was found to consume 33 flip-flops on the CLBs, i.e., 16% of the total available flip-flops. • Impleme ...
AD13280 Dual-Channel, 12-Bit, 80 MSPS ADC with Analog Input Signal
... All ac specifications tested by driving ENCODE and ENCODE differentially. Single-ended input: AMP-IN-x-1 = 1 V p-p, AMP-IN-x-2 = GND. Gain tests are performed on the AMP-IN-x-1 input voltage range. ...
... All ac specifications tested by driving ENCODE and ENCODE differentially. Single-ended input: AMP-IN-x-1 = 1 V p-p, AMP-IN-x-2 = GND. Gain tests are performed on the AMP-IN-x-1 input voltage range. ...
500 MHz Four-Quadrant Multiplier AD834 Data Sheet FEATURES
... a transconductance bandwidth (RL = 50 Ω) in excess of 500 MHz from either of the differential voltage inputs. In multiplier modes, the typical total full-scale error is 0.5%, dependent on the application mode and the external circuitry. Performance is relatively insensitive to temperature and supply ...
... a transconductance bandwidth (RL = 50 Ω) in excess of 500 MHz from either of the differential voltage inputs. In multiplier modes, the typical total full-scale error is 0.5%, dependent on the application mode and the external circuitry. Performance is relatively insensitive to temperature and supply ...
C) Votage controll oscillator
... input signals, and generates a pulse whose width is a time difference of rising edges of input signals. The pulse width of PFD output should be short from a view point of output noise, because output pulse contains a voltage or current noise. In other words rising edges of two input signals of each ...
... input signals, and generates a pulse whose width is a time difference of rising edges of input signals. The pulse width of PFD output should be short from a view point of output noise, because output pulse contains a voltage or current noise. In other words rising edges of two input signals of each ...
The Zeeman and Hyperfine Splittings of Mercury Emission
... so that its FSR matches that of the low field interferogram. However, increasing the FSR means decreasing D, which would in fact cause the high field points in the linear fit to take on even higher y-values, yielding even less linearity. Furthermore, in all these fits, it has been assumed that if on ...
... so that its FSR matches that of the low field interferogram. However, increasing the FSR means decreasing D, which would in fact cause the high field points in the linear fit to take on even higher y-values, yielding even less linearity. Furthermore, in all these fits, it has been assumed that if on ...
Continuous Phase Shift of Sinusoidal Signals Using Injection
... shifters have been reported in the literature. For fixed amounts of phase shift (i.e., multiples of 90 ), poly-phase networks are the preferred solutions [1]. When a digitally controlled phase shift is required, phase shifters based on PIN or varactor diodes and FET transistors are commonly used [2] ...
... shifters have been reported in the literature. For fixed amounts of phase shift (i.e., multiples of 90 ), poly-phase networks are the preferred solutions [1]. When a digitally controlled phase shift is required, phase shifters based on PIN or varactor diodes and FET transistors are commonly used [2] ...
Signal detector circuit
... is at a given level which is more positive than the Field of the invention 30 potential at the source, the resistance of the transistor The present invention is related to the signal de is very high and no signal passes from the source 14 to the drain 22, the input signal being conducted to ground t ...
... is at a given level which is more positive than the Field of the invention 30 potential at the source, the resistance of the transistor The present invention is related to the signal de is very high and no signal passes from the source 14 to the drain 22, the input signal being conducted to ground t ...
High Gain Bandwidth Product, Precision Fast FET™ Op Amp AD8067
... High common-mode rejection ratio: −106 dB Low power: 6.5 mA typical supply current Low cost Small packaging: SOT-23-5 ...
... High common-mode rejection ratio: −106 dB Low power: 6.5 mA typical supply current Low cost Small packaging: SOT-23-5 ...
LMH6609 900MHz Voltage Feedback Op Amp
... A proper printed circuit layout is essential for achieving high frequency performance. TI provides evaluation boards for the LMH6609 as shown above. These boards were laid out for optimum, high-speed performance. The ground plane was removed near the input and output pins to reduce parasitic capacit ...
... A proper printed circuit layout is essential for achieving high frequency performance. TI provides evaluation boards for the LMH6609 as shown above. These boards were laid out for optimum, high-speed performance. The ground plane was removed near the input and output pins to reduce parasitic capacit ...
