AD9762 Data Sheet
... Differential current outputs are provided to support singleended or differential applications. Matching between the two current outputs ensures enhanced dynamic performance in a differential output configuration. The current outputs may be tied directly to an output resistor to provide two complemen ...
... Differential current outputs are provided to support singleended or differential applications. Matching between the two current outputs ensures enhanced dynamic performance in a differential output configuration. The current outputs may be tied directly to an output resistor to provide two complemen ...
Lecture material
... However, third-order products often fall within the system bandwidth and produce a distortion called third-order intercept distortion. Third-order intercept distortion is a special case of intermodulation distortion and the predominant form of frequency distortion. Third-order intermodulation compon ...
... However, third-order products often fall within the system bandwidth and produce a distortion called third-order intercept distortion. Third-order intercept distortion is a special case of intermodulation distortion and the predominant form of frequency distortion. Third-order intermodulation compon ...
![arXiv:1010.2685v1 [physics.optics] 13 Oct 2010](http://s1.studyres.com/store/data/020802655_1-4639143493fc4ed9838d2a5c6779e83a-300x300.png)
arXiv:1010.2685v1 [physics.optics] 13 Oct 2010
... suspension positions of the mounting points were optimized by finite element (FEM) calculations. In previous measurements large frequency changes of the resonator mode were observed under accelerations. It was assumed that mechanical contact of the spacer to the housing was the source of this effect ...
... suspension positions of the mounting points were optimized by finite element (FEM) calculations. In previous measurements large frequency changes of the resonator mode were observed under accelerations. It was assumed that mechanical contact of the spacer to the housing was the source of this effect ...
Analysis of Conventional and Novel Delay Lines: A Numerical Study
... cause a timing imbalance at the receiver end. ...
... cause a timing imbalance at the receiver end. ...
CC2541-Q1 - Texas Instruments
... The CC2541-Q1 is a power-optimized true Wireless MCU solution for both Bluetooth low energy and proprietary 2.4-GHz applications. This device enables the building of robust nework nodes with low total bill-of-material costs. The CC2541-Q1 combines the excellent performance of a leading RF transceive ...
... The CC2541-Q1 is a power-optimized true Wireless MCU solution for both Bluetooth low energy and proprietary 2.4-GHz applications. This device enables the building of robust nework nodes with low total bill-of-material costs. The CC2541-Q1 combines the excellent performance of a leading RF transceive ...
An 868 MHz Low Power, Low Phase Noise LC VCO in 0
... synthesizers. With the introduction of new applications, designers have been focusing on different architectures and different trade-offs in PLL designs to satisfy the requirements of the emerging applications with low cost and low power [3]-[10]. The goal of this work is to generate quadrature LO s ...
... synthesizers. With the introduction of new applications, designers have been focusing on different architectures and different trade-offs in PLL designs to satisfy the requirements of the emerging applications with low cost and low power [3]-[10]. The goal of this work is to generate quadrature LO s ...
Programmable 27-Bit Parallel-to-Serial Receiver
... SubLVDS interface from the transmitting device. Once the SN65LVDS308 detects the presence of the clock and the PLL has locked onto PCLK, then the parity is checked. Parity-error detection ensures detection of all single-bit errors in one pixel and 50% of all multibit errors. The parity bit covers th ...
... SubLVDS interface from the transmitting device. Once the SN65LVDS308 detects the presence of the clock and the PLL has locked onto PCLK, then the parity is checked. Parity-error detection ensures detection of all single-bit errors in one pixel and 50% of all multibit errors. The parity bit covers th ...
71M6513 Neutral Current Measurement
... Firmware Procedure for Measuring Neutral Current 1. The Neutral Current measurement is performed by acquiring the auxiliary input data from the V3 pin (pin 86). 2. The analog data measured is referenced to the VBIAS pin (pin 81). 3. Analog input V3 data can be read using the MUX_ALT mode bit in the ...
... Firmware Procedure for Measuring Neutral Current 1. The Neutral Current measurement is performed by acquiring the auxiliary input data from the V3 pin (pin 86). 2. The analog data measured is referenced to the VBIAS pin (pin 81). 3. Analog input V3 data can be read using the MUX_ALT mode bit in the ...
2946A Avionics Communications Service Monitor Communication
... Duplex - provided as standard Full duplex operation is provided by the 2946A. This allows testing of duplex radios as well as simultaneous testing of repeater transmit and receive paths. There are no restrictions to the duplex offset. Cellular and Trunking - built in AMPS, TACS and NMT analog cellul ...
... Duplex - provided as standard Full duplex operation is provided by the 2946A. This allows testing of duplex radios as well as simultaneous testing of repeater transmit and receive paths. There are no restrictions to the duplex offset. Cellular and Trunking - built in AMPS, TACS and NMT analog cellul ...
RADPAL POWER-ON-RESET VDD RAMP RATE REQUIREMENTS
... analysis of the problem was performed. The analysis found that the RADPAL only failed if a residual voltage of about 400mV was on the VDD pin before power ramped to 5 volts. If VDD started at zero volts, the RADPAL always powered up correctly under all conditions of temperature, process parameters a ...
... analysis of the problem was performed. The analysis found that the RADPAL only failed if a residual voltage of about 400mV was on the VDD pin before power ramped to 5 volts. If VDD started at zero volts, the RADPAL always powered up correctly under all conditions of temperature, process parameters a ...
extracting musically-relevant rhythmic information from dance
... Figure 1. Several representations in the time domain of frame-differencing graphs of movement of waving hand. Figures 1a) and b), same frequency, with two different amplitudes; 1c), faster frequency with amplitude variation. ...
... Figure 1. Several representations in the time domain of frame-differencing graphs of movement of waving hand. Figures 1a) and b), same frequency, with two different amplitudes; 1c), faster frequency with amplitude variation. ...
9. Capacitor and Resistor Circuits
... should have measured first before connecting the capacitor and resistor in the circuit. PART B: With channel 1 of the oscilloscope, measure the voltage across the signal generator and with channel 2 measure the voltage across the resistor. Compare with the graphs of the second example above. Make th ...
... should have measured first before connecting the capacitor and resistor in the circuit. PART B: With channel 1 of the oscilloscope, measure the voltage across the signal generator and with channel 2 measure the voltage across the resistor. Compare with the graphs of the second example above. Make th ...