• Study Resource
  • Explore
    • Arts & Humanities
    • Business
    • Engineering & Technology
    • Foreign Language
    • History
    • Math
    • Science
    • Social Science

    Top subcategories

    • Advanced Math
    • Algebra
    • Basic Math
    • Calculus
    • Geometry
    • Linear Algebra
    • Pre-Algebra
    • Pre-Calculus
    • Statistics And Probability
    • Trigonometry
    • other →

    Top subcategories

    • Astronomy
    • Astrophysics
    • Biology
    • Chemistry
    • Earth Science
    • Environmental Science
    • Health Science
    • Physics
    • other →

    Top subcategories

    • Anthropology
    • Law
    • Political Science
    • Psychology
    • Sociology
    • other →

    Top subcategories

    • Accounting
    • Economics
    • Finance
    • Management
    • other →

    Top subcategories

    • Aerospace Engineering
    • Bioengineering
    • Chemical Engineering
    • Civil Engineering
    • Computer Science
    • Electrical Engineering
    • Industrial Engineering
    • Mechanical Engineering
    • Web Design
    • other →

    Top subcategories

    • Architecture
    • Communications
    • English
    • Gender Studies
    • Music
    • Performing Arts
    • Philosophy
    • Religious Studies
    • Writing
    • other →

    Top subcategories

    • Ancient History
    • European History
    • US History
    • World History
    • other →

    Top subcategories

    • Croatian
    • Czech
    • Finnish
    • Greek
    • Hindi
    • Japanese
    • Korean
    • Persian
    • Swedish
    • Turkish
    • other →
 
Profile Documents Logout
Upload
sesdu5v0wb
sesdu5v0wb

LM2937 - Solarbotics.net
LM2937 - Solarbotics.net

... It is important to note that for most capacitors, ESR is specified only at room temperature. However, the designer must ensure that the ESR will stay inside the limits shown over the entire operating temperature range for the design. For aluminum electrolytic capacitors, ESR will increase by about 3 ...
HOW TO PREVENT ELECTRICAL FIRES
HOW TO PREVENT ELECTRICAL FIRES

Anomalies in mid-high-temperature linear thermal expansion
Anomalies in mid-high-temperature linear thermal expansion

AN3964
AN3964

... This application note describes a method of implementing a simple application for temperature measurement using the STM32L-DISCOVERY. The solution described in this document uses the integrated temperature sensor of the STM32L1 microcontroller. The factory or user calibration method is described to ...
Ch25 - MrsCDsAPPhysics
Ch25 - MrsCDsAPPhysics

ST-100, ST-110, ST-200, and ST-300
ST-100, ST-110, ST-200, and ST-300

... options available. The main advantages of thermistors over other electronic thermometers (thermocouples, platinum resistance thermometers) are high signal-to-noise ratio, requirement of only a single-ended channel for measurement, and low cost, while still maintaining comparable accuracy. Apogee Ins ...
11b.2 Balancing Electrical and Thermal Device Characteristics
11b.2 Balancing Electrical and Thermal Device Characteristics

... collector-up HBTs with emitter connected directly to a heatsink through a thru-wafer via[3], or use of partial vias[4,5]. Metal heat shunts [1] can reduce the device thermal resistance by more than half without degrading the RF characteristics, but this method is mostly applicable to high power GaAs ...
CLU701-1002C4 - citizen electronics co.,ltd.
CLU701-1002C4 - citizen electronics co.,ltd.

H3 ECO REGRANULATED MATERIAL FOR HIGH ECONOMIC
H3 ECO REGRANULATED MATERIAL FOR HIGH ECONOMIC

Informal Logic
Informal Logic

... It can have three leads called the gate, source, and drain, but often has only a source and drain A FETs is basically a solid-state resistor with most of its resistance being controlled by the amount of reverse bias applied to the gate FETs are useful for building certain types of sensors since the ...
Fundamentals of Thermal Resistance Measurement
Fundamentals of Thermal Resistance Measurement

... The selection of the sense current is the first step for device calibration. The selection of this current is limited by a number of factors although within a fairly wide range, the precise selection is not critical. Generally, the best sense current is the smallest one which does not encroach on an ...
DC CIRCUITS UNIT 3 POWER POINT HONORS
DC CIRCUITS UNIT 3 POWER POINT HONORS

... AND R2 ARE IN PARALLEL, SO THAT THE TOTAL CIRCUIT RESISTANCE IS SMALLER THAN WHEN THE ...
Ground Source Closed-Loop Heat Pumps
Ground Source Closed-Loop Heat Pumps

... closed-loop heat pump consists of one or more factory-made assemblies which normally include an indoor conditioning coil with air moving means, compressor(s) and refrigerant-tofluid heat exchanger(s), including means to provide both cooling and heating, cooling only or heating only functions. When s ...
Electrical conduction
Electrical conduction

... 2.11 Electromigration and Black’s equations ...
File
File

Lab7 Temperature Measurement
Lab7 Temperature Measurement

ppt
ppt

Temperature and its Effect on Electro
Temperature and its Effect on Electro

Archive: Circuits Free Response
Archive: Circuits Free Response

ZD20CF Series - Teledyne Relays
ZD20CF Series - Teledyne Relays

SQF – thermal protected power resistor from Ty
SQF – thermal protected power resistor from Ty

Circuits - Mansfield Public Schools
Circuits - Mansfield Public Schools

... The voltmeter must be placed in parallel with the element being measured. The resistance of the voltmeter must be very high so that very little current will pass through the meter. An RC circuit is one that contains a resistor, a capacitor and an ideal battery. One can write an equation for the pote ...
8/4/99 - IRIS - Lake Land College
8/4/99 - IRIS - Lake Land College

Spring Learning Targets
Spring Learning Targets

< 1 ... 78 79 80 81 82 83 84 85 86 ... 194 >

Lumped element model



The lumped element model (also called lumped parameter model, or lumped component model) simplifies the description of the behaviour of spatially distributed physical systems into a topology consisting of discrete entities that approximate the behaviour of the distributed system under certain assumptions. It is useful in electrical systems (including electronics), mechanical multibody systems, heat transfer, acoustics, etc.Mathematically speaking, the simplification reduces the state space of the system to a finite dimension, and the partial differential equations (PDEs) of the continuous (infinite-dimensional) time and space model of the physical system into ordinary differential equations (ODEs) with a finite number of parameters.
  • studyres.com © 2025
  • DMCA
  • Privacy
  • Terms
  • Report