ADF4360-7 - Analog Devices
... VCO Output. The output level is programmable from −5 dBm to −14 dBm. See the Output Matching section for a description of the various output stages. VCO Complementary Output. The output level is programmable from −5 dBm to −14 dBm. See the Output Matching section for a description of the various out ...
... VCO Output. The output level is programmable from −5 dBm to −14 dBm. See the Output Matching section for a description of the various output stages. VCO Complementary Output. The output level is programmable from −5 dBm to −14 dBm. See the Output Matching section for a description of the various out ...
PDF
... The external trigger is derived from a 12-120 VAC source. For example, the laboratory benches include a 25 VAC line-to-neutral single- or three-phase source, which can be fed into the external trigger. For more sophisticated experiments, if line-to-neutral voltages are less than 120, they can be use ...
... The external trigger is derived from a 12-120 VAC source. For example, the laboratory benches include a 25 VAC line-to-neutral single- or three-phase source, which can be fed into the external trigger. For more sophisticated experiments, if line-to-neutral voltages are less than 120, they can be use ...
ppt - Electrical Engineering & Computer Sciences
... ° The worst case scenario for hold time consideration: • The input register sees CLK2 • The output register sees CLK1 • fast FF2 output must not change input to FF1 for same clock edge ...
... ° The worst case scenario for hold time consideration: • The input register sees CLK2 • The output register sees CLK1 • fast FF2 output must not change input to FF1 for same clock edge ...
Solderless (well, almost) homebrew electronic projects by Lyle
... circuits to keep leads as short as practical (not necessarily as short as possible). Keeping them short also reduces the chances of two bare component leads touching each other. For most small components and short jumper wires, I try to bend the leads to fit the desired hole spacing, and then insert ...
... circuits to keep leads as short as practical (not necessarily as short as possible). Keeping them short also reduces the chances of two bare component leads touching each other. For most small components and short jumper wires, I try to bend the leads to fit the desired hole spacing, and then insert ...
mae511
... counter and, of course, the ADC. The output of the first flip-flop, denoted Q1 , is sent to the CLR input of the counter, to ensure that the counter is synchronized with Q1 . This means that the counter only counts for the first 24 ADC clock pulses, and the outputs are set to logical low (ground) fo ...
... counter and, of course, the ADC. The output of the first flip-flop, denoted Q1 , is sent to the CLR input of the counter, to ensure that the counter is synchronized with Q1 . This means that the counter only counts for the first 24 ADC clock pulses, and the outputs are set to logical low (ground) fo ...
ADS5203 数据资料 dataSheet 下载
... (1) Integral nonlinearity refers to the deviation of each individual code from a line drawn from zero to full-scale. The point used as zero occurs ½LSB before the first code transition. The full-scale point is defined as a level ½LSB beyond the last code transition. The deviation is measured from th ...
... (1) Integral nonlinearity refers to the deviation of each individual code from a line drawn from zero to full-scale. The point used as zero occurs ½LSB before the first code transition. The full-scale point is defined as a level ½LSB beyond the last code transition. The deviation is measured from th ...
Lesson Objectives
... Break down a known measurement system and show how the components correlate to generic measurement system blocks. ...
... Break down a known measurement system and show how the components correlate to generic measurement system blocks. ...
10-Bit, 210 MSPS TxDAC D/A Converter AD9740
... on performance, resolution, and cost. The AD9740 offers exceptional ac and dc performance while supporting update rates up to 210 MSPS. The AD9740’s low power dissipation makes it well suited for portable and low power applications. Its power dissipation can be further reduced to 60 mW with a slight ...
... on performance, resolution, and cost. The AD9740 offers exceptional ac and dc performance while supporting update rates up to 210 MSPS. The AD9740’s low power dissipation makes it well suited for portable and low power applications. Its power dissipation can be further reduced to 60 mW with a slight ...
XIO1100 Data Manual (Rev. C)
... Specification). P1 is used for the Disabled state, all Detect states, and L1.Idle state of the Link Training and Status State Machine (LTSSM). While in P1 state, the optional P1_SLEEP input signal can be used to reduce even more power consumption by disabling the RX_CLK signal. However, the P1_SLEEP ...
... Specification). P1 is used for the Disabled state, all Detect states, and L1.Idle state of the Link Training and Status State Machine (LTSSM). While in P1 state, the optional P1_SLEEP input signal can be used to reduce even more power consumption by disabling the RX_CLK signal. However, the P1_SLEEP ...
AD723 数据手册DataSheet下载
... After the luma prefilter, the bandlimited luma signal is sampled onto a set of capacitors at twice the master reference clock rate. After an appropriate delay, the data is read from the delay line, reconstructing the luma signal. The 8FSC oversampling of this delay line limits the amount of jitter i ...
... After the luma prefilter, the bandlimited luma signal is sampled onto a set of capacitors at twice the master reference clock rate. After an appropriate delay, the data is read from the delay line, reconstructing the luma signal. The 8FSC oversampling of this delay line limits the amount of jitter i ...
Ultrafast polarization switching in thin-film ferroelectrics
... step-function-like electrical pulses. Quantitative measurements yield a polarization switching time, t s , of ⬃220 ps when measured with a 5 V, 68 ps rise time input electrical pulse. Modeling of the switching transients using the Merz–Ishibashi model and Merz–Shur model of switching kinetics yields ...
... step-function-like electrical pulses. Quantitative measurements yield a polarization switching time, t s , of ⬃220 ps when measured with a 5 V, 68 ps rise time input electrical pulse. Modeling of the switching transients using the Merz–Ishibashi model and Merz–Shur model of switching kinetics yields ...
Time-to-digital converter
In electronic instrumentation and signal processing, a time to digital converter (abbreviated TDC) is a device for recognizing events and providing a digital representation of the time they occurred. For example, a TDC might output the time of arrival for each incoming pulse. Some applications wish to measure the time interval between two events rather than some notion of an absolute time.In electronics time-to-digital converters (TDCs) or time digitizers are devices commonly used to measure a time interval and convert it into digital (binary) output. In some cases interpolating TDCs are also called time counters (TCs).TDCs are used in many different applications, where the time interval between two signal pulses (start and stop pulse) should be determined. Measurement is started and stopped, when either the rising or the falling edge of a signal pulse crosses a set threshold. These requirements are fulfilled in many physical experiments, like time-of-flight and lifetime measurements in atomic and high energy physics, experiments that involve laser ranging and electronic research involving the testing of integrated circuits and high-speed data transfer.