![Atlas Level 1 Calorimeter Trigger Common Merger eXtended module (CMX) Hardware Description](http://s1.studyres.com/store/data/008861285_1-bc6901676773a88dbadf16c647ba0162-300x300.png)
Atlas Level 1 Calorimeter Trigger Common Merger eXtended module (CMX) Hardware Description
... http://www.pa.msu.edu/hep/atlas/l1calo/cmx/specification/2_design_study/ ...
... http://www.pa.msu.edu/hep/atlas/l1calo/cmx/specification/2_design_study/ ...
Indoor HID - Acuity Brands
... lamp on if there is a power interruption or brownout significant enough to cause the primary HID lamp to drop out. The 120V quartz lamp stays on until the HID fixture restrikes. QRS does not energize during cold start of HID luminaires. Wiring for the quartz lamp is internal to the ballast assembly; ...
... lamp on if there is a power interruption or brownout significant enough to cause the primary HID lamp to drop out. The 120V quartz lamp stays on until the HID fixture restrikes. QRS does not energize during cold start of HID luminaires. Wiring for the quartz lamp is internal to the ballast assembly; ...
Atlas Level 1 Calorimeter Trigger Common Merger eXtended module (CMX) Prototype Review
... of the Card Layout and finally (7) a table of the number of CMX cards to be built. This document also contains appendices which include circuit diagrams and engineering notes used to design the card. The use of large FPGAs with well over a thousand pins per device does not make the standard schemati ...
... of the Card Layout and finally (7) a table of the number of CMX cards to be built. This document also contains appendices which include circuit diagrams and engineering notes used to design the card. The use of large FPGAs with well over a thousand pins per device does not make the standard schemati ...
Pipelined ADC Enhancement Techniques
... by more than 20dB within only 104 clock cycles in an 11-bit 45MS/s pipelined ADC - more than two orders of magnitude faster than previously published reports. The second technique develops a new MDAC topology which enables a pipelined ADC to be designed without a front-end sample-and-hold, and thus ...
... by more than 20dB within only 104 clock cycles in an 11-bit 45MS/s pipelined ADC - more than two orders of magnitude faster than previously published reports. The second technique develops a new MDAC topology which enables a pipelined ADC to be designed without a front-end sample-and-hold, and thus ...
SBC BL2600 User’s Manual C-Programmable Single-Board Computer with Ethernet 019–0142_M
... All other trademarks are the property of their respective owners. Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International. Digi provides this document "as is," without warranty of any kind, expressed or implied, including ...
... All other trademarks are the property of their respective owners. Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International. Digi provides this document "as is," without warranty of any kind, expressed or implied, including ...
HP 4155A/4156A Semiconductor Parameter Analyzer User`s Task
... HP 4155A/4156A can perform stress testing. That is, can force a speci ed dc voltage or current for the speci ed duration. Also, you can force ac stress by using pulse generator units (PGUs), which are installed in HP 41501A SMU/Pulse Generator Expander. The HP 41501A is attached to HP 4155A or HP 41 ...
... HP 4155A/4156A can perform stress testing. That is, can force a speci ed dc voltage or current for the speci ed duration. Also, you can force ac stress by using pulse generator units (PGUs), which are installed in HP 41501A SMU/Pulse Generator Expander. The HP 41501A is attached to HP 4155A or HP 41 ...
Installation, Operation and Maintenance Manual
... coupling parts. Even when the motor is stopped, it should be considered “alive” as long as its controller is energized. Automatic circuits may start the motor at any time. Keep hands away from the output shaft until the motor has completely stopped and power is disconnected from the controller. Moto ...
... coupling parts. Even when the motor is stopped, it should be considered “alive” as long as its controller is energized. Automatic circuits may start the motor at any time. Keep hands away from the output shaft until the motor has completely stopped and power is disconnected from the controller. Moto ...
single photon counting for ultra-weak fluorescence
... application of large-area SPAD for highly sensitive detection of DNA-sequences is demonstrated. Recently solid-state alternative to the traditional photomultiplier tube (PMT) called silicon photomultiplier (SiPM) became commercially available. SiPMs are analog detectors (output signal proportional t ...
... application of large-area SPAD for highly sensitive detection of DNA-sequences is demonstrated. Recently solid-state alternative to the traditional photomultiplier tube (PMT) called silicon photomultiplier (SiPM) became commercially available. SiPMs are analog detectors (output signal proportional t ...
74HC4040; 74HCT4040 1. General description 12-stage binary ripple counter
... Product data sheet ...
... Product data sheet ...
Time-to-digital converter
![](https://commons.wikimedia.org/wiki/Special:FilePath/CMOS_TW_OSC_000.png?width=300)
In electronic instrumentation and signal processing, a time to digital converter (abbreviated TDC) is a device for recognizing events and providing a digital representation of the time they occurred. For example, a TDC might output the time of arrival for each incoming pulse. Some applications wish to measure the time interval between two events rather than some notion of an absolute time.In electronics time-to-digital converters (TDCs) or time digitizers are devices commonly used to measure a time interval and convert it into digital (binary) output. In some cases interpolating TDCs are also called time counters (TCs).TDCs are used in many different applications, where the time interval between two signal pulses (start and stop pulse) should be determined. Measurement is started and stopped, when either the rising or the falling edge of a signal pulse crosses a set threshold. These requirements are fulfilled in many physical experiments, like time-of-flight and lifetime measurements in atomic and high energy physics, experiments that involve laser ranging and electronic research involving the testing of integrated circuits and high-speed data transfer.