Download Voltage Transducer LV 100-600 VPN = 600 V

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Ground loop (electricity) wikipedia , lookup

Transistor wikipedia , lookup

Mercury-arc valve wikipedia , lookup

Brushed DC electric motor wikipedia , lookup

Transformer wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

Decibel wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Power inverter wikipedia , lookup

Power engineering wikipedia , lookup

Ground (electricity) wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Stepper motor wikipedia , lookup

Islanding wikipedia , lookup

Electrical ballast wikipedia , lookup

Resonant inductive coupling wikipedia , lookup

Three-phase electric power wikipedia , lookup

Current source wikipedia , lookup

Schmitt trigger wikipedia , lookup

Ohm's law wikipedia , lookup

Electrical substation wikipedia , lookup

Triode wikipedia , lookup

History of electric power transmission wikipedia , lookup

Rectifier wikipedia , lookup

Metadyne wikipedia , lookup

Distribution management system wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Power electronics wikipedia , lookup

Power MOSFET wikipedia , lookup

Voltage regulator wikipedia , lookup

Buck converter wikipedia , lookup

Surge protector wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Opto-isolator wikipedia , lookup

Alternating current wikipedia , lookup

Stray voltage wikipedia , lookup

Voltage optimisation wikipedia , lookup

Mains electricity wikipedia , lookup

Transcript
Voltage Transducer LV 100-600
For the electronic measurement of voltages: DC, AC, pulsed...,
with galvanic isolation between the primary circuit (high voltage)
and the secondary circuit (electronic circuit).
VPN = 600 V
Electrical data
VPN
Primary nominal voltage rms
VPM
Primary voltage, measuring range
IPN
Primary nominal current rms
R
Measuring resistance
M
600
0 .. ± 900
16.66
RM min RM max
with ± 15 V
0210 Ω
0120 Ω
ISN
K N
VC
IC
@ ± 600 V max
@ ± 900 V max
Secondary nominal current rms
Conversion ratio
Supply voltage (± 5 %)
Current consumption
50
600 V : 50 mA
± 15
< 32 + IS
V
V
mA
mA
V
mA
Accuracy - Dynamic performance data
XG
εL
IO
IOT
Overall accuracy @ VPN, TA = 25°C
± 0.9
Linearity error
< 0.1
Typ Max
Offset current @ IP = 0, TA = 25°C
± 0.2
Temperature variation of IO 0°C .. + 70°C
± 0.2 ± 0.3
tr
Response time to 90 % of VPN step
90
%
%
mA
mA
µs
●● Closed loop (compensated)
voltage transducer using Hall
effect
●● Isolated plastic case recognized
according to UL 94-V0
●● Primary resistor R1 incorporated
within the housing.
Advantages
●●
●●
●●
●●
●●
●●
●●
Excellent accuracy
Very good linearity
Low temperature drift
Optimized response time
Wide frequency bandwidth
No insertion losses
High immunity to external
interference.
Applications
General data
TA
TS
NP
P
R 1
RS
m
Features
Ambient operating temperature 0 .. + 70
Ambient storage temperature
- 25 .. + 85
Turns ratio
6000 : 2000
Total primary power loss
10
Primary resistance @ TA = 25°C
36
Secondary coil resistance @ TA = 70°C
55
Mass
790
Standards
EN 50178: 1997
°C
°C
W
kΩ
Ω
g
●● AC variable speed drives and
servo motor drives
●● Static converters for DC motor
drives
●● Uninterruptible Power Supplies
(UPS)
●● Power supplies for welding
applications.
Application domain
●● Industrial.
Page 1/3
110413/5
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice
www.lem.com
Voltage Transducer LV 100-600
Isolation characteristic
Vd
Vw
Rms voltage for AC isolation test, 50 Hz, 1 min
Impulse withstand voltage 1.2/50 µs
6
8
kV
kV
dCp
dCI
CTI
Creepage distance
Clearance distance
Comparative Tracking Index (group I)
Min
55.12
27.9
600
mm
mm
Applications examples
According to EN 50178 and IEC 61010-1 standards and following conditions:
●● Over voltage category OV 3
●● Pollution degree PD2
●● Non-uniform field
dCp, dCI, Vw
EN 50178
IEC 61010-1
Rated insulation voltage
Nominal voltage
Single insulation
600 V
600 V
Reinforced insulation
600 V
600 V
Safety
This transducer must be used in electric/electronic equipment with respect
to applicable standards and safety requirements in accordance with the
manufacturer’s operating instructions.
Caution, risk of electrical shock
When operating the transducer, certain parts of the module can carry hazardous
voltage (eg. primary busbar, power supply).
Ignoring this warning can lead to injury and/or cause serious damage.
This transducer is a build-in device, whose conducting parts must be inaccessible
after installation.
A protective housing or additional shield could be used.
Main supply must be able to be disconnected.
Page 2/3
110413/5
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice
www.lem.com
Dimensions LV 100-600 (in mm)
Connection
Remarks
Mechanical characteristics
●● General tolerance
●● Transducer fastening
Recommended fastening torque
●● Connection of primary
●● Connection of secondary
●● Connection of ground
Recommended fastening torque
± 0.3 mm
2 holes Ø 6.5 mm,
2 M6 steel screws
5 Nm
M5 threaded studs
Faston 6.3 x 0.8 mm
M5 threaded stud
2.2 Nm
●● IS is positive when VP is applied on terminal +HT.
●● The primary circuit of the transducer must be linked to the
connections where the voltage has to be measured.
●● This is a standard model. For different versions (supply
voltages, turns ratios, unidirectional measurements...),
please contact us.
Page 3/3
110413/5
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice
www.lem.com