Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
SAMI BRUSHES for Street Sweepers Manual for Operation OPERATIONAL INSTRUCTION Technical Specification: MODEL Width, mm Dia of brush Chain, mm Turning Angle +/- Weight, kg Tractor (kW) 2200H 2200 700 25o 350 30 to 75 2700H 2700 700 25o 390 30 to 75 SAMI Brush for sweeping streets (hereinafter 'the brush') may be used either as attached to the standard three-point rear linkage system, or as attached to front loader linkage. The support wheels (two pcs.) can be mounted either in front of the brush, or behind it, depending on requirement. The support legs (two pcs.) are to be mounted depending on position of the support wheels, i.e. on the other side of the brush. Minimum requirement in oil to start travel of the brush: 65 litre/min Additional Equipment: - Support wheels 15/6.00 Supplies: SAMI brushes are supplied in complete sets as ready-to-use items, or in complete sets specially packed for delivery. Hydraulic cylinders are supplied without oil. Mounting the Brush: 1. Attach the brush to the standard three-point rear linkage system of the tractor. Adjust the front frame into the vertical position making use the longitudinal long tie-rod. Connect the hydraulic hoses to the tractor hydraulic system. Check the working of the hydraulic system prior to the start of works. If the brush rotates in the same direction as the wheels rotate, change the ends of the hoses connected to the hydraulic engine. If the hydraulic system does not work, check, first of all, compatibility / fixation of the ends of the gear connections, and further, working the hydraulic system of the tractor. 2. Fasten the brush to the linkage system of the front loader, and connect the hydraulic hoses. SAFETY PRECAUTIONS NB! Be careful while attaching the brush to the tractor. NB! Make sure nobody is standing near the tractor to avoid an accident. NB! When driving, be careful at making turns so that the brush would not hit external obstacles. NB! Lower the brush to the ground before leaving the tractor. NB! Check the connections of the hydraulic hoses and make sure oil does not leak. NB! Before starting works, make sure the support legs are raised. Purpose: The brush is intended for sweeping streets/ roads with hard road surface. The brush position can be adjusted by the long tie-rod or by lateral tie-rods of the tractor. The height of bristle above the working surface can be adjusted by changing the height of the support wheels. For this purpose, the appropriate handle is to be turned and the suitable height is to be fixed by the locking nut. The brush turning is adjusted by means of the hydraulic cylinder. The extreme limits of the hydraulic cylinder give maximum and minimum angle of turning. Maintenance: Daily check shall be done in regard of the following: fastening the support legs, air pressure in tyres, hydraulic connections, free rotation of the bristle. Monthly check includes the chain tension, condition of the bearings and journal, and also, additional greasing the greasing points. Storing: Before placing the SAMI brush for long-term storing, cover the piston rod of its hydraulic cylinder with preservative agent to protect it against corrosion. Warranty: SAMI Limited issues the warranty for the brush for six (6) month since the date of its purchase. - Under the warranty, failures of materials and manufacturing revealed within the warranty time will be rectified. - Working hours of such repairs are to be paid for only provided the manufacturer does not execute the repairs. - The manufacturer either rectifies defective parts or replaces defective parts by new ones. - The manufacturer only based on the agreement between the manufacturer and customer may effect reimbursement of costs incurred by a customer for purchase of the machine parts. - As to parts made by sub-contractors, warranties of particular makers of such parts shall be valid. - Repairs under the warranty do not extend the warranty time. The Warranty does not cover the following: - Wearing parts (e.g. brushes, and so forth) Shutdown time and other external costs and losses Transport costs Overtime and daily salary The Warranty does not recover losses due to: - Negligent and incorrect use of the brushes Failure to meet the Manufacturer's requirements in regard of operation and maintenance of the brush - Natural wear and tear - Abnormal conditions for the brush using - Overloads or the brush use which differs from its purpose - Lack of up-keep and monitoring condition of the brushes - Poor quality of repairs executed - Using equipment and spare parts from other manufacturers instead of original parts made by SAMI Ltd. - Lengthy shelf life in intermediary's warehouses, due to, for example: corrosive effects and painting drawbacks. All the said terms of the Warranty are valid only for new brushes purchased from the dealers authorised by the Manufacturer. The Warranty does not cover any re-sold brushes. Should any failures occur, contacts should be made with the Manufacturer or the authorised dealer. Prior to contacting, write down reference data: the year of manufacture / number of brush series. Refer the data on the appropriate nameplate. Manufacturer: AS SAMI Tule 20, Saue, 76501 ESTONIA Tel : +372 6709 621 Fax : + 372 6709 039 e-mail: [email protected] www.sami.ee