* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download MR. SURRETTE VAN NUYS HIGH SCHOOL CHAPTER 13
Survey
Document related concepts
Index of electronics articles wikipedia , lookup
Surge protector wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Galvanometer wikipedia , lookup
Thermal runaway wikipedia , lookup
Superconductivity wikipedia , lookup
Power MOSFET wikipedia , lookup
Rectiverter wikipedia , lookup
Negative resistance wikipedia , lookup
Current mirror wikipedia , lookup
Current source wikipedia , lookup
RLC circuit wikipedia , lookup
Lumped element model wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Transcript
MR. SURRETTE VAN NUYS HIGH SCHOOL CHAPTER 13: ELECTRIC DC CURRENT AND RESISTANCE WORKSHEET SOLUTIONS 1. The heating coil of a hot water heater has a resistance of 50.0 ohm and operates at 120 V. What is its power rating? 1A. (1) P = V2 / R (2) P = (120 V)2 / 50.0 (3) P = 288 W 2. If a certain resistor obeys Ohm’s law, its resistance will change: (A) as voltage only across the resistor changes (B) as current only through the resistor changes (C) as both voltage and current change (D) as energy given off by the electrons in their collisions changes (E) none of the above 2A. (E) none of the above 3. A certain material is in a room at 27.0oC. If the absolute temperature K of the material is tripled, its resistance also triples. What is the value for , the temperature coefficient of resistivity? 3A. (1) R = Ro(1 + (T – To)) (2) (T – To) = (R/Ro) – 1 (3) R = 3Ro (4) (T – To) = (3Ro/Ro) – 1 (5) (T – To) = 2 (6) = 2 / (T – To) (7) = 2 / (900 K – 300 K) (8) = 2 / 600 K (9) = 0.0033 / oC 4. A platinum wire is utilized to determine the melting point of indium. The resistance of the platinum wire is 2.00 at 20.0oC and increases to 3.072 as the indium starts to melt. platinum = 3.92 x 10-3/oC. What is the melting temperature of indium (in oC)? 4A. (1) R = Ro(1 + (T – To)) (2) T = [(R – Ro) / (Ro)] + To (3) T = [(3.072 – 2.00 ) / (3.92x10-3/oC)(2.00 )] + 293.15 K (4) T = 136.7 K + 293.15 K (5) T = 429.9 K (6) Tc = T – 273.15 (7) Tc = 156.7oC 1|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 5. A color television set draws 3.15 A when connected to 220 V. What is the cost (with electrical energy at 7 cents/kWh) of running the color TV for 8 hours? 5A. (1) Determine joules used: P = IV (2) P = (3.15 A)(220 V) (3) P = 693 W = 693 J/s (4) (8 hours) (3600 sec / 1 hour) (693 J / 1 sec) = 2.00 x 107 J (5) 2.00 x 107 J (1 kWh) = 5.54 kWh -------------3.6 x 106 J (6) Determine cost: (5.54 kWh) (7 cents) (7) Cost = 38.8 cents 6. An electric car runs off a bank of 18.0 V batteries with total energy storage of 4.55 x 109 J. If the electric motor draws 6000 W in moving the car at a steady speed of 20 m/s, how far will the car go (in km) before it runs out of fuel? 6A. (1) Determine time car can move: Time = (4.55 x 107 J) (6000 W) (2) Time = (4.55 x 107 J) (1 sec / 6000 J) (3) Time = 7583 s (4) Determine distance car can move: (7583 s) (20 m/s) = 1.52 x 105 m (5) 1.52 x 105 m (1 km / 1000 m) = 152 km 7. How long does it take for 0.2 C to pass through a frictionless wire in a 9 amp circuit? 7A. (1) I = Q / t (2) t = Q / I (3) t = 0.2 C / 9A (4) t = 2.22 x 10-2 s 8. A metal wire has a radius of 0.45 mm, is 0.85 m long, and has a resistance of 15.0 ohms. What must be the length of a second wire made of the same type of metal if its radius is 0.10 mm and also has a resistance of 15.0 ohms? 8A. (1) R1 = L1 / A (2) = R1A / L1 (3) A = r2 (4) = R1r2 / L1 (5) = (15 ) (4.5 x 10-4 m)2 / 0.85 m (6) = 1.123 x 10-5 .m (7) R2 = L2 / A 2|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 8A. (continued…) (8) L2 = R2A / (9) L2 = R2(r2) / (10) L2 = (15 ) (1 x 10-4 m)2 / 1.123 x 10-5 .m (11) L2 = 4.20 x 10-2 m (12) L2 = 4.20 cm 3|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL CHAPTER 13: ELECTRIC DC DIRECT CURRENT WORKSHEET SOLUTIONS 1. The following three appliances are connected to a 120 volt house circuit: (i) toaster, 1350 W (ii) coffee pot, 750 W (iii) microwave, 600 W If all were operated at the same time, what total current would they draw? 1A. (1) P = IV (2) I = P / V (3) I = 2850 W / 120 V (4) I = (2850 J/s) / (120 C/J) (5) I = 23.8 C/s = 23.8 A 2. A circuit contains a 3.00 volt battery, a 2.00 ohm resistor, a 0.30 microfarad capacitor, an ammeter, and a switch, all in series. What will be the current reading 10 min after the switch is closed? 2A. zero 3. Three resistors, with values of 3.00, 6.00, and 12.0 ohms, respectively, are connected in parallel. What is the equivalent resistance of this combination? 3A. (1) 1/Rp = (1/Ri) (2) 1/Rp = 1 / 3 + 1 / 6 + 1 / 12 (3) 1/Rp = 7 / 12 (4) Rp = 12 / 7 (5) Rp = 1.7 4. Which resistor above is in series with resistor R? 4A. (d) R4 (a) R1 (b) R2 (c ) R3 (d) R4 4|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 5. What is the equivalent resistance for these resistors? 5A. (1) Req (top part): Req = R1 + R2 (2) Req = 6 + 10 = 16 (3) Req (top + bottom): 1 / Req = 1 / R1 + 1 / R2 (4) 1 / Req = 1 / 16 + 1 / 4 (5) 1 / Req = 5 / 16 (6) Req = 16/5 (7) Req (total): Req = R1 + R2 (8) Req = 2 + 16/5 = 26/5 (9) Req = 5.2 6. Consider the circuit below. 6a. Only two resistors in this circuit can be combined into one equivalent resistance. Which two are they? A. 2 and 1 6b. What is the value of the unspecified resistance on top? A. (1) Req = R1 + R2 (2) Req = 2 + 1 (3) Req = 3 5|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 6c. The next step in the circuit reduction is as shown below. What is the value of the unspecified resistance? A. (1) (2) (3) (4) (5) 6d. A. (1) (2) (3) 6e. A. (1) (2) (3) (4) (5) 6f. A. (1) (2) (3) 1 / Req = 1 / R1 + 1 / R2 1 / Req = 1 / 3 + 1 / 6 1 / Req = 2 / 6 + 1 / 6 1 / Req = 3 / 6 = 1 / 2 Req = 2 How much is the single resistance representing all four of the original resistors? Req = R1 + R2 Req = 3 + 2 Req = 5 The current through the battery (and the 3 resistor) is thus: V=IR V = I Req I = V / Req I = 20V / 5 I=4A The total power dissipated by the circuit is: P = IV P = (4A)(20V) P = 80 W 7. A 20 volt battery is connected across a 5 ohm resistor, as shown. 6|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 7a. Which end of the resistor is at the higher potential, A or B? A. Point A 7b. The 5 ohm resistor consists of a block of material with terminals at A and B. The electric field inside this material must either be directed from A to B or from B to A. Which is it? A. From A to B. Electric field flows out of the positive end of the battery and into the negative end of the battery. 7c. The direction of conventional current (electrons) through R must be: A. It is directed from B to A through the resistor. 7d. The voltage across the 5 ohm resistor is: A. 20V. The battery supplies the voltage. 7e. A. (1) (2) (3) (4) The current through the 5 ohm resistor is given by Ohm’s law and is: V = IR I=V/R I = 20V / 5 I=4A 7f. Electrons scatter off atoms in the resistor and transfer energy (heat) to them. The rate of heat production, or the power dissipated in the 5 ohm resistor, is: A. (1) P = IV (2) P = (4A)(20V) (3) P = 80 W 7|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL CHAPTER 13: ELECTRIC DC QUIZ SOLUTIONS 1. A color television set draws about 3.25 A when connected to 120 V. What is the cost (with electrical energy at 8 cents/kWh) of running the color TV for 14 hours? 1A. (1) Determine joules used: P = IV (2) P = (3.25 A)(120 V) (3) P = 390 W = 390 J/s (4) (14 hours) (3600 sec / 1 hour) (390 J / 1 sec) = 1.97 x 107 J (5) 8.64 x 107 J (1 kWh) = 5.47 kWh -------------3.6 x 106 J (6) Determine cost: (5.47 kWh) (8 cents) (7) Cost = 43.7 cents 2. A wire is utilized to determine the melting point of a metal. The resistance of the wire is 4.00 at 20.0oC and increases to 7.034 as the metal starts to melt. = 4.78 x 10-3/oC. What is the melting temperature (in oC)? 2A. (1) R = Ro(1 + (T – To)) (2) T = [(R – Ro) / (Ro)] + To (3) T = [(7.034 – 4.00 ) / (4.78 x 10-3/oC)(4.00 )] + 293 K (4) T = 158.7 K + 293 K (5) T = 451.7 K (6) T = Tc + 273.15 (7) Tc = T – 273.15 (8) Tc = 451.7 – 273.15 = 178.6oC 3. An electric car is designed to run off a bank of 18.0 V batteries with total energy storage of 3.15 x 107 J. If the electric motor draws 9200 W in moving the car at a steady speed of 22 m/s, how far will the car go (in km) before it runs out of fuel? 3A. (1) Determine time car can move: Time = (3.15 x 107 J) (9200 W) (2) Time = (3.15 x 107 J) (1 sec / 9200 J) (3) Time = 3424 s (4) Determine distance car can move: (3424 s) (22 m/s) = 7.53 x 104 m (5) 7.53 x 104 m (1 km / 1000 m) = 75.3 km 4. The heating coil of a hot water heater has a resistance of 27.0 ohm and operates at 180 V. What is its power rating? 4A. (1) P = V2 / R (2) P = (180 V)2 / 27.0 (3) P = 1200 W 8|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 5. A certain material is in a room at 42.0oC. If the absolute temperature K of the material is doubled, its resistance also doubles. What is the value for , the temperature coefficient of resistivity? 5A. (1) R = Ro(1 + (T – To)) (2) (T – To) = (R/Ro) – 1 (3) R = 2Ro (4) (T – To) = (2Ro/Ro) – 1 (5) (T – To) = 1 (6) = 1 / (T – To) (7) = 1 / (630 K – 315 K) (8) = 1 / 315 K (9) = 3.17 x 10-3 / oC 6. Three resistors, with values of 4.00, 6.00, and 18.0 ohms, respectively, are connected in parallel. What is the overall resistance of this combination? 6A. (1) 1 / Req = 1 / R1 + 1 / R2 + 1 / R3 (2) 1 / Req = 1 / 4 + 1 / 6 + 1 / 18 (3) 1 / Req = 9 / 36 (4) 1 / Req = 17 / 36 (5) Req = (36/ 17) Questions 7 - 8. A circuit obeys Ohm’s law. It contains a 12 volt battery and a 4 resistor. 7. The current in this circuit is: 7A. (1) V = IR (2) V = IReq (3) I = V / Req (4) I = 12V / 4 (5) I = 3.0 A 8. The total power dissipated by the circuit is: 8A. (1) P = IV (2) P = (3A)(12V) (3) P = 36 W 9|Page PHYSICS MR. SURRETTE VAN NUYS HIGH SCHOOL 9. Consider the circuit below: 1. 10 2. 5 3. 6 4. 3 9a. Only two resistors in this circuit can be combined into one equivalent series resistance. Which two are they? A. (1.) and (2.) 9b. What is the value of the unspecified resistance on top? A. (1) Req = R1 + R2 (2) Req = 10 + 5 (3) Req = 15 9c. The next step in the circuit reduction is as shown below. What is the value of the unspecified resistance? A. (1) (2) (3) (4) (5) 1 / Req = 1 / R1 + 1 / R2 1 / Req = 1 / 15 + 1 / 6 1 / Req = 2 / 30 + 5 / 30 1 / Req = 7 / 30 Req = 30/7 10 | P a g e PHYSICS MR. SURRETTE 9d. A. (1) (2) (3) VAN NUYS HIGH SCHOOL How much is the single resistance representing all four of the original resistors? Req = R1 + R2 Req = 4.29 + 3 Req = 7.3 10. The following three appliances are connected to a 120 volt house circuit: (i) toaster, 1325 W (ii) coffee pot, 950 W; and (iii) microwave, 675 W. If all were operated at the same time, what total current would they draw? 10A. (1) P = IV (2) I = P / V (3) I = 2950 W / 120 V (4) I = (2950 J/s) / (120 C/J) (5) I = 24.58 C/s = 24.6 A 11. How long does it take for 1.5 C to pass through a frictionless wire in a 12 amp circuit? 11A. (1) I = Q / t (2) t = Q / I (3) t = 1.5 C / 12 A (4) t = 0.125 s 12. A metal wire has a radius of 1.45 mm, is 1.85 m long, and has a resistance of 15.0 ohms. What must be the length of a second wire made of the same type of metal if its radius is 0.10 mm and also has a resistance of 15.0 ohms? 12A. (1) R1 = L1 / A (2) = R1A / L1 (3) A = r2 (4) = R1r2 / L1 (5) = (15 ) (1.45 x 10-3 m)2 / 1.85 m (6) = 5.356 x 10-5 .m (7) R2 = L2 / A (8) L2 = R2A / (9) L2 = R2(r2) / (10) L2 = (15 ) (1 x 10-4 m)2 / 5.356 x 10-5 .m (11) L2 = 8.80 x 10-3 m (12) L2 = 0.9 cm 11 | P a g e PHYSICS