Download Test Procedure for the NCV8853GEVB Evaluation Board

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Standing wave ratio wikipedia , lookup

Oscilloscope types wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

Oscilloscope wikipedia , lookup

Audio power wikipedia , lookup

Flip-flop (electronics) wikipedia , lookup

Index of electronics articles wikipedia , lookup

Analog television wikipedia , lookup

Test probe wikipedia , lookup

Multimeter wikipedia , lookup

Superheterodyne receiver wikipedia , lookup

Ohm's law wikipedia , lookup

Josephson voltage standard wikipedia , lookup

Amplifier wikipedia , lookup

Phase-locked loop wikipedia , lookup

Oscilloscope history wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

CMOS wikipedia , lookup

Integrating ADC wikipedia , lookup

Current source wikipedia , lookup

Wilson current mirror wikipedia , lookup

Radio transmitter design wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Valve audio amplifier technical specification wikipedia , lookup

Surge protector wikipedia , lookup

Power MOSFET wikipedia , lookup

Operational amplifier wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

Schmitt trigger wikipedia , lookup

Voltage regulator wikipedia , lookup

Power electronics wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Opto-isolator wikipedia , lookup

Rectiverter wikipedia , lookup

Transcript
Test Procedure for the NCV8853GEVB Evaluation Board
Table 1. DEMONSTRATION BOARD TERMINALS
Pin Name
VIN
VOUT
GND
EN/SYNC
PG
PG+
Function
Positive dc input voltage
Regulated dc output voltage
Common dc return
Enable input and external clock synchronization input
Digital power good output
Power good pull-up. Use this pin only when pulling-up PG to an
external voltage source.
Table 2. ABSOLUTE MAXIMUM RATINGS
(Voltages are with respect to GND)
Rating
Value
Units
Dc supply voltage (VIN)
-0.3 to 36
V
Dc supply voltage (EN/SYNC, PG, PG+)
-0.3 to 6.0
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only.
Functional operation above the Recommended Operating Conditions is not implied. Extended exposure
to stresses above the Recommended Operating Conditions may affect device reliability.
Table 3. ELECTRICAL CHARACTERISTICS
(TA = 25°C, 6.0 V ≤ VIN ≤ 36 V, VEN/SYNC = 5.0 V, 0 ≤ IOUT ≤ 2.0 A, unless otherwise specified)
Characteristics
Output Voltage
Voltage Accuracy
Line Regulation
Load Regulation
Conditions
Regulation
IOUT = 1.0 A
VIN = 13.2 V
Switching
Switching Frequency
Soft-start Time
SYNC Input Frequency Range
Typical Value
Units
5.0
2
0.04
0.12
V
%
%
%
340
2.0
270 to 500
kHz
ms
kHz
3.33
5.0
A
A
3.1
170
V
°C
Current Limit
Average Current Limit
Cycle-by-cycle Current Limit
Input Undervoltage Lockout (UVLO)
Thermal Shutdown
4/5/2013
Protections
VIN decreasing
TJ rising
www.BDTIC.com/ON/
-1-
www.onsemi.com
PG
PG_POS
R6
VOUT
U1
R1
GND
VIN
OPEN
PG
1
PG
VIN
R2
30m
8
C1
0.1uF
C3225X7S1H106K
C2
C3
10uF
10uF
C4
10uF
VIN
10k
EN/SY NC
2
C5
EN/SY NC 6800p
R3
COMP
C6
470p
3
FB
4
EN/SY NC ISNS
COMP
GDRV
FB
GND
ISNS
7
6
GDRV
VSW
5
R5
8.06k
VOUT
15 uH
XAL5050-153MEB
GND
D1
MBRA340T3
885300
R4
8.06k
GND
NTTFS5116PL
Q1
L1
C8 VOUT
C7
100 uF 0.1uF
B45197A2107K409
GND
42.2k
Figure 1: NCV885300EVB Board Schematic
Operational Guidelines
1. Connect a dc input voltage, within the 6.0 V to 36 V range, between VIN and GND
2. Connect a load between VOUT and GND
3. Connect a dc enable voltage, within the 2.0 V to 5.5 V range, between EN/SYNC and GND
4. Optionally, for external clock synchronization, connect a pulse source between EN/SYNC and
GND. The high state level should be within the 2.0 V to 5.5 V range, and the low state level
within the 0.0 V to 0.8 V range, with a frequency within the 170 kHz to 500 kHz range.
5. Make sure that the output maintains 1 A at 5 volts.
6. Using an oscilloscope, test the switching frequency of the GDRV pin (pin 6) of U1. It should be
≈340 kHz when internally synchronized.
7. If using the optional external clock synchronization from step 4 the switching frequency should
match the input source frequency.
8. To check the Input Undervoltage Lockout (UVLO) slowly decrease the input down towards 0 V.
The board should turn off at around 3.1 V.
4/5/2013
www.BDTIC.com/ON/
-2-
www.onsemi.com
VIN
IOUT
ZOUT
VEN
VSY
NC
VEN Figure 2: NCV885300EVB Board Connections
Power Good Operation
1. The Power Good pin (PG) allows you to digitally monitor the output voltage. When above 90% of
the expected value, the PG signal is in a high state. By default, it is pulled high to VOUT through
a 10kΩ resistor.
2. Optional: To pull the PG pin high using a signal other than VOUT, please make the following
board modifications:
a. Remove R1 from the board.
b. Populate R6 with a 10 kΩ resistor.
c. Connect the a voltage source between PG+ and GND (please see the Absolute
Maximum Ratings table for more information).
d. PG is now ready to digitally monitor VOUT using an external pull-up.
4/5/2013
www.BDTIC.com/ON/
-3-
www.onsemi.com
Typical Performance
Regulation
Figure 3: Line Regulation for 340 kHz and a 5.0 V output
Figure 4: Load Regulation for 340 kHz and a 5.0 V output
4/5/2013
www.BDTIC.com/ON/
-4-
www.onsemi.com