Download FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch FSU S

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Power inverter wikipedia , lookup

Electrical ballast wikipedia , lookup

Electrical substation wikipedia , lookup

Ohm's law wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Transistor wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Current source wikipedia , lookup

Alternating current wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Switch wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Stray voltage wikipedia , lookup

Crossbar switch wikipedia , lookup

Light switch wikipedia , lookup

Rectifier wikipedia , lookup

Surge protector wikipedia , lookup

Voltage regulator wikipedia , lookup

Voltage optimisation wikipedia , lookup

Power electronics wikipedia , lookup

Semiconductor device wikipedia , lookup

Schmitt trigger wikipedia , lookup

Mains electricity wikipedia , lookup

P–n diode wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Buck converter wikipedia , lookup

Opto-isolator wikipedia , lookup

Two-port network wikipedia , lookup

Transcript
FSUSB104 — Low-Power, Two-Port, Hi-Speed,
USB2.0 (480Mbps) Switch
Features
Description
ƒ
ƒ
ƒ
The FSUSB104 is a bi-directional, low-power, two-port,
Hi-Speed, USB2.0 switch. Configured as a double-pole,
double-throw switch (DPDT) switch, it is optimized for
switching between two Hi-Speed (480Mbps) sources or
a Hi-Speed and Full-Speed (12Mbps) source.
Low On Capacitance: 3.7pF Typical
Low On Resistance: 3.9Ω Typical
Low Power Consumption: 1μA Maximum
- 15μA Maximum ICCT over an Expanded Voltage
The FSUSB104 is compatible with the requirements of
USB2.0 and features an extremely low on capacitance
(CON) of 3.7pF. The wide bandwidth of this device
(720MHz) exceeds the bandwidth needed to pass the
third harmonic, resulting in signals with minimum edge
and phase distortion. Superior channel-to-channel
crosstalk also minimizes interference.
Range (VIN=1.8V, VCC=4.3V)
ƒ
ƒ
ƒ
ƒ
Wide -3db Bandwidth: > 720MHz
Packaged in Pb-free 10-Lead UMLP (1.4 x 1.8mm)
8kV ESD Rating, >16kV Power/GND ESD Rating
Power-Off Protection on All Ports When VCC=0V
- D+/D- Pins Tolerate up to 5.25V
Applications
ƒ
ƒ
Cell phone, PDA, Digital Camera, and Notebook
LCD Monitor, TV, and Set-Top Box
IMPORTANT NOTE:
For additional performance information, please contact
[email protected].
The FSUSB104 contains special circuitry on the switch
I/O pins for applications where the VCC supply is
powered-off (VCC=0), which allows the device to
withstand an over-voltage condition. This device is
designed to minimize current consumption even when
the control voltage applied to the SEL pin is lower than
the supply voltage (VCC). This feature is especially
valuable to ultra-portable applications, such as cell
phones, allowing for direct interface with the generalpurpose I/Os of the baseband processor. Other
applications include switching and connector sharing in
portable cell phones, PDAs, digital cameras, printers,
and notebook computers.
Ordering Information
Part Number
Top
Mark
Operating
Temperature
Range
FSUSB104UMX
JF
-40 to +85°C
Package
Eco Status
Green
10-Lead, Quad, Ultrathin Molded Leadless
Package (UMLP), 1.4 x 1.8mm
MicroPak™ is a trademark of Fairchild Semiconductor Corporation.
For Fairchild’s definition of Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html.
HSD1+
D+
HSD2+
HSD1-
D-
HSD2Sel
Control
/OE
Figure 1. Analog Symbol
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
www.fairchildsemi.com
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
December 2009
GN D
3
HSD2-
4
HSD2+
5
D- D+
2
1
6
10
Sel
9
VCC
8 /OE
7
HSD1- HSD1+
Figure 2. FSUSB104 Pin Assignment 10L UMLP
(Top Through View)
Pin Definitions
Pin #
Name
Description
1
D+
USB Data Bus
2
D-
USB Data Bus
3
GND
Ground
4
HSD2-
Multiplexed Source inputs
5
HSD2+
Multiplexed Source inputs
6
HSD1-
Multiplexed Source inputs
7
HSD1+
Multiplexed Source inputs
8
/OE
Switch Enable
9
VCC
Supply Voltage
10
Sel
Switch Select
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
Pin Assignments
Truth Table
Sel
/OE
Function
X
HIGH
Disconnect
LOW
LOW
D+, D-=HSD1+, HSD1-
HIGH
LOW
D+, D-=HSD2+, HSD2-
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
www.fairchildsemi.com
2
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device
reliability. The absolute maximum ratings are stress ratings only.
Symbol
VCC
VCNTRL
Parameter
Supply Voltage
DC Input Voltage (S, /OE)
(1)
VSW
DC Switch I/O Voltage
IIK
DC Input Diode Current
IOUT
DC Output Current
TSTG
Storage Temperature
ESD
(1)
Min.
Max.
Unit
-0.5
+5.5
V
-0.5
VCC
V
-0.5
VCC + 0.3
V
-50
-65
Human Body Model, JEDEC: JESD22-A114
mA
50
mA
+150
°C
All Pins
7
I/O to GND
8
Power to GND
16
Charged Device Model, JEDEC: JESD22-C101
kV
2
Note:
1. The input and output negative ratings may be exceeded if the input and output diode current ratings are
observed.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
VCC
VCNTRL
VSW
TA
Parameter
Min.
Max.
Unit
3.0
4.3
V
0
VCC
V
Switch I/O Voltage
-0.5
4.5
V
Operating Temperature
-40
+85
°C
Supply Voltage
Control Input Voltage (S, /OE)
(2)
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
Absolute Maximum Ratings
Note:
2. The control input must be held HIGH or LOW and it must not float.
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
www.fairchildsemi.com
3
All typical value are at 25°C unless otherwise specified.
Symbol
Parameter
Conditions
VIK
Clamp Diode Voltage
VIH
Input Voltage High
VIL
Input Voltage Low
IIN
Control Input Leakage
VSW =0 to VCC
4.3
IOZ
Off State Leakage
0 ≤ Dn, HSD1n, HSD2n
≤ 3.6V
IOFF
Power-Off Leakage Current
(All I/O Ports)
VSW =0V to 4.3V, VCC=0V
Figure 4
RON
HS Switch On Resistance
∆RON
HS Delta Ron
IIN=-18mA
VCC (V)
(3)
(4)
TA=- 40ºC to +85ºC
Min.
Typ.
3.0
Units
Max.
-1.2
V
3.0 to 3.6
1.3
V
4.3
1.7
V
3.0 to 3.6
0.5
V
4.3
0.7
V
-1
1
µA
4.3
-2
2
µA
0
-2
2
µA
6.5
Ω
VSW =0.4V, ION=-8mA
Figure 3,
3.0
3.9
VSW =0.4V, ION=-8mA
3.0
0.65
Ω
ICC
Quiescent Supply Current
VCNTRL=0 or VCC, IOUT=0
4.3
1.0
µA
ICCT
Increase in ICC Current per
Control Voltage and VCC
VCNTRL =2.6V, VCC=4.3V
4.3
10.0
µA
VCNTRL =1.8V, VCC=4.3V
4.3
15.0
µA
Notes:
3. Measured by the voltage drop between HSDn and Dn pins at the indicated current through the switch.
On resistance is determined by the lower of the voltage on the two (HSDn or Dn ports).
4. Guaranteed by characterization.
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
DC Electrical Characteristics
www.fairchildsemi.com
4
All typical value are for VCC=3.3V at 25°C unless otherwise specified.
Symbol
Parameter
Conditions
VCC (V)
TA=- 40ºC to +85ºC
Min.
Typ.
Max.
Units
tON
Turn-On Time
S, /OE to Output
RL=50Ω, CL=5pF
VSW =0.8V
Figure 5, Figure 6
3.0 to 3.6
13
30
ns
tOFF
Turn-Off Time
S, /OE to Output
RL=50Ω, CL=5pF
VSW =0.8V
Figure 5, Figure 6
3.0 to 3.6
12
25
ns
tPD
Propagation Delay
CL=5 pF, RL=50Ω
Figure 5, Figure 7
3.3
0.25
tBBM
Break-Before-Make
RL=50Ω, CL=5pF
VSW1=VSW2=0.8V
Figure 9
3.0 to 3.6
OIRR
Off Isolation
RL=50Ω, f=240MHz
Figure 11
3.0 to 3.6
-30
dB
Xtalk
Non-Adjacent Channel
Crosstalk
RL=50Ω, f=240MHz
Figure 12
3.0 to 3.6
-45
dB
720
MHz
550
MHz
BW
(5)
-3db Bandwidth
RL=50Ω, CL=0pF
Figure 10
2.0
ns
6.5
ns
3.0 to 3.6
RL=50Ω, CL=5pF
Figure 10
Note:
5. Guaranteed by characterization.
USB Hi-Speed-Related AC Electrical Characteristics
Symbol
Parameter
Conditions
Vcc (V)
TA=- 40ºC to +85ºC
Min.
tSK(P)
tJ
Skew of Opposite Transitions
(6)
of the Same Output
(6)
Total Jitter
Typ.
Units
Max.
CL=5pF, RL=50Ω
Figure 8
3.0 to 3.6
20
ps
RL=50Ω, CL=5pf,
tR=tF=500ps (10-90%) at
480Mbps
15
(PRBS=2 – 1)
3.0 to 3.6
200
ps
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
AC Electrical Characteristics
Note:
6. Guaranteed by characterization.
Capacitance
Symbol
Parameter
Conditions
TA=- 40ºC to +85ºC
Min.
Typ.
CIN
Control Pin Input Capacitance
VCC=0V
1.5
CON
D+/D- On Capacitance
VCC=3.3V, /OE=0V, f=240MHz
Figure 14
3.7
COFF
D1n, D2n Off Capacitance
VCC and /OE=3.3V
See Figure 13
2.0
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
Units
Max.
pF
www.fairchildsemi.com
5
VON
I Dn(OFF)
NC
HSDn
A
VSW
Dn
VSW
Select
GND
I ON
Select
R ON =
VON / ION
V Sel =
V Sel =
GND
Figure 4. Off Leakage
tRISE = 2.5ns
Dn
VSW
CL
GND RS
0 orV
V cc
**Each switch port is tested separately
0 orV cc
Figure 3. On Resistance
HSDn
GND
RL
tFALL = 2.5ns
VCC
V OUT
Input – V/OE , VSel
GND
10%
GND
V Sel
VOH
GND
Output- VOUT
RL , RS , and C L are functions of the application
environment (see AC Tables for specific values)
CL includes test fixture and stray capacitance.
VOL
Figure 5. AC Test Circuit Load
90%
90%
VCC /2
VCC /2
90%
tON
90%
tOFF
Figure 6. Turn-On / Turn-Off Waveforms
tFALL = 500ps
tRISE = 500ps
50%
Input
0V
400mV
+400mV
tPHL
- 400mV
90%
0V
50%
tPLH
10%
10%
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
Test Diagrams
90%
10%
VOH
Output
50%
50%
Output
VOL
t PHL
Figure 7. Propagation Delay (tRtF – 500ps)
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
t PLH
Figure 8. Intra-Pair Skew Test tSK(P)
www.fairchildsemi.com
6
tRISE = 2.5ns
Vcc
HSDn
Dn
VSW1
GND
CL
VSW2
RL
10%
0V
VOUT
VOUT
GND
GND
90%
Vcc/2
Input - VSel
0.9*Vout
0.9*Vout
RS
tBBM
VSel
RL , RS , and C L are functions of the application
environment (see AC Tables for specific values)
CL includes test fixture and stray capacitance.
GND
Figure 9. Break-Before-Make Interval Timing
Network Analyzer
Network Analyzer
RS
GND
RS
V IN
VS
GND
VSel
GND
VSel
VOUT
GND
VS
GND
V OUT
GND
RS and RT are functions of the application
environment (see AC Tables for specific values).
GND
V IN
GND
GND
RT
RS and RT are functions of the application
environment (see AC Tables for specific values).
GND
RT
RT
GND
Off isolation = 20 Log (V OUT / VIN)
Figure 10. Bandwidth
Figure 11. Channel Off Isolation
Network Analyzer
NC
RS
V IN
GND
VS
VSel
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
Test Diagrams (Continued)
GND
GND
RT
GND
GND
RS and RT are functions of the application environment
(see AC Tables for specific values).
V OUT
RT
GND
Crosstalk = 20 Log (VOUT / VIN)
Figure 12. Non-Adjacent Channel-to-Channel Crosstalk
HSDn
Capacitance
Meter
S
Capacitance
Meter
S
VSel = 0 or Vcc
V Sel = 0 or Vcc
HSDn
HSDn
Figure 13. Channel Off Capacitance
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
HSDn
Figure 14.
Channel On Capacitance
www.fairchildsemi.com
7
0.15 C
A
1.40
2X
1.700
B
9X
0.563
0.663
1
1.80
PIN #1 QUADRANT
2.100
0.400
0.15 C
2X
10X
0.225
TOP VIEW
RECOMMENDED LAND PATTERN
0.55 MAX.
1.450
0.10 C
0.550
0.152
9X
0.450
SEATING
PLANE
0.08 C
0.050
C
0.400
SIDE VIEW
1.850
10X
0.225
3
9X
0.35
0.45
0.45
0.55
OPTIONAL MINIMIAL TOE LAND PATTERN
0.40
6
1
10
0.500
0.15
10X
0.25
0.100
0.10 C A B
0.05 C
0.100
0.100
BOTTOM VIEW
DETAIL A
PIN #1 TERMINAL
SCALE: 2X
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
Physical Dimensions
A. DIMENSIONS ARE IN MILLIMETERS.
B. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994
C. DRAWING FILENAME: UMLP10Arev2
Figure 15. 10-Lead, Ultrathin Molded Leadless Package (UMLP)
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify
or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions,
specifically the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
www.fairchildsemi.com
8
FSUSB104 — Low-Power, Two-Port, Hi-Speed, USB2.0 (480Mbps) Switch
© 2008 Fairchild Semiconductor Corporation
FSUSB104 • Rev. 1.0.2
www.fairchildsemi.com
9