Download μ PD166021T1F Data Sheet

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Power engineering wikipedia , lookup

Transistor wikipedia , lookup

Power inverter wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Mercury-arc valve wikipedia , lookup

Three-phase electric power wikipedia , lookup

Stepper motor wikipedia , lookup

History of electric power transmission wikipedia , lookup

Electrical ballast wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Thermal runaway wikipedia , lookup

Electrical substation wikipedia , lookup

Two-port network wikipedia , lookup

Schmitt trigger wikipedia , lookup

Islanding wikipedia , lookup

P–n diode wikipedia , lookup

TRIAC wikipedia , lookup

Triode wikipedia , lookup

Voltage optimisation wikipedia , lookup

Rectifier wikipedia , lookup

Voltage regulator wikipedia , lookup

Ohm's law wikipedia , lookup

Stray voltage wikipedia , lookup

Earthing system wikipedia , lookup

Mains electricity wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Power electronics wikipedia , lookup

Surge protector wikipedia , lookup

Power MOSFET wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Current source wikipedia , lookup

Alternating current wikipedia , lookup

Opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

Buck converter wikipedia , lookup

Transcript
Preliminary Data Sheet
μPD166021T1F
R07DS0442EJ0100
Rev.1.00
Sep 07, 2011
MOS INTEGRATED CIRCUIT
1. Overview
1.1 Description
The μPD166021T1F is a single N-channel high-side switch with charge pump, diagnostic feedback with load current
sense and embedded protection functions.
1.2 Features
• Built-in charge pump
• Low on-state resistance
• Short circuit protection
- Shutdown by over current detection and over load detection
• Over temperature protection
- Shutdown by over temperature detection and keep off-state
• Built-in diagnostic function
- Proportional load current sensing
- Defined fault signal in case of abnormal load condition
• Under voltage lock out
• Reverse battery protection by self turn on of N-ch MOSFET
• Small multi-chip package: JEDEC 5-pin TO-252 (MSL: 3, profile acc. J-STD-20C)
• AEC Qualified
1.3 Applications
• Light bulb (to 65 W) switching
• Switching of all types of 14 V DC grounded loads, such as LED, inductor, resistor and capacitor
• Replacement for fuse and relay
2. Ordering Information
Part No.
μ PD166021T1F-E1-AY ∗1
Lead plating
Sn
Packing
Tape 2500 p/reel
Package
5-pin TO-252 (MP-3ZK)
Note: ∗1. Pb-free (This product does not contain Pb in the external electrode.)
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 1 of 23
μPD166021T1F
Chapter Title
3. Specification
3.1 Block Diagram
3 & Tab
ICC
VCC
VCC - VIN
Internal
power supply
Charge pump
Power supply
voltage sense
Current
detector
Dynamic
clamp
Output voltage
sense
Current sense
Output voltage
clamp
IIN
IN
2
ESD
protection
VIN
Control logic
VCC
VON
1&5
IL
OUT
Fault signal
output
Load
IIS
IS
ESD
protection
VOUT
4
Temperature
Sensor
VIS
RIS
3.2 Pin Configuration
Pin No.
1
2
3/Tab
4
5
Terminal Name
OUT
IN
VCC
IS
OUT
Tab
1
2
3
4
5
Pin Function
Terminal Name
OUT
IN
VCC
IS
Pin function
Output to load
Activates the output, if it shorted to ground
Supply Voltage; tab and pin 3 are internally
shorted
Sense output, diagnostic feedback
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Recommended connections
Pin 1 and Pin 5 must be externally shorted
If reverse battery protection feature is used, refer to
3.6.3 Power Dissipation Under Reverse Battery
Condition.
Connected to battery voltage with small 100 nF
capacitor in parallel
If current sense and diagnostic feature are not used,
connected to GND via resistor
Page 2 of 23
μPD166021T1F
Chapter Title
3.3 Absolute Maximum Ratings
TA = 25°C, unless otherwise specified
Parameter
VCC Voltage
Symbol
VCC1
VCC2
Rating
28
42
Unit
V
V
VCC voltage under Load
Dump condition
VCC Voltage at reverse
battery condition
−VCC
−16
V
Load Current
(Short circuit current)
Power dissipation (DC)
IL(SC)
Self limited
A
PD
1.2
W
Voltage of IN pin
VIN
V
Voltage of IS pin
VIS
Inductive load switch-off
energy dissipation single
pulse
EAS1
VCC − 28
VCC + 14
VCC − 28
VCC + 14
50
mJ
Maximum allowable
energy dissipation at
shutdown operation
EAS2
105
mJ
Channel Temperature
Tch
Dynamic temperature
increase while switching
Storage Temperature
ESD susceptibility
ΔTch
−40 to +150
60
°C
°C
Tstg
VESD
−55 to +150
2000
°C
V
HBM
400
V
MM
V
Test Conditions
RI = 1 Ω, RL = 1.5 Ω, RIS = 1 kΩ, td = 400 ms
RL = 2.2 Ω, 1 min.
TA = 85°C,
Device on 50 mm x 50 mm x 1.5 mm epoxy PCB
2
FR4 with 6 cm of 70 μm copper area
DC
At reverse battery condition, t < 1 min.
DC
At reverse battery condition, t < 1 min.
VCC = 12 V, IL = 10 A, Tch,start ≤ 150°C
refer to 3.6.8 Inductive Load Switch Off Energy
Dissipation for a Single Pulse
VCC = 18 V, Tch,star ≤ 150°C,
Lsupply = 5 μH, Lshort = 15 μH
refer to 3.6.9 Maximum Allowable Switch off
Energy (Single Pulse)
AEC-Q100-002 std.
R = 1.5 kΩ, C = 100 pF
AEC-Q100-003 std.
R = 0 Ω, C = 200 pF
3.4 Thermal Characteristics
Parameter
Thermal characteristics
Symbol
Rth(ch-a)
Rth(ch-c)
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
MIN.
TYP.
45
MAX.
3.17
Unit
°C/W
Test Conditions
Device on 50 mm x 50 mm x 1.5 mm
epoxy PCB FR4 with 6 cm2 of 70 μm
copper area
°C/W
Page 3 of 23
μPD166021T1F
Chapter Title
3.5 Electrical Characteristics
Operation Function
Tch = 25°C, VCC = 12 V, unless otherwise specified
Parameter
Required current capability
of Input switch
Input current for turn-off
Standby Current
Symbol
IIH
IIL
ICC(off)
MIN.
TYP.
1.0
MAX.
2.2
Unit
mA
2.5
50
5.0
μA
μA
2.5
15.0
μA
10
18
65
Test Conditions
Tch = −40 to 150°C
RL = 2.2 Ω, Iin = 0 A, Tch = 25°C
RL = 2.2 Ω, Iin = 0 A,
Tch = −40 to 150°C
On State Resistance
Ron
Output voltage drop
limitation at small load
current
Von(NL)
8
14
30
Turn On Time
ton
120
360
μs
Turn Off Time
toff
250
500
μs
Slew rate on *1
dv/dton
0.2
0.8
V/μs
25 to 50% VOUT, RL = 2.2 Ω, Tch = −40 to
150°C, refer to 3.6.6 Measurement
Condition
−dv/dtoff
0.2
0.6
V/μs
50 to 25% VOUT, RL = 2.2 Ω, Tch = −40 to
150°C, refer to 3.6.6 Measurement
Condition
Slew rate off
*1
mΩ
mV
IL = 7.5 A, Tch = 25°C
IL = 7.5 A, Tch = 150°C
Tch = −40 to 150°C
RL = 2.2 Ω, Tch = −40 to 150°C,
refer to 3.6.6 Measurement Condition
Note: ∗1. Not tested, specified by design
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 4 of 23
μPD166021T1F
Chapter Title
Protection Function
Tch = 25°C, VCC = 12 V, unless otherwise specified
Parameter
On-state resistance at
reverse battery condition
Symbol
MIN.
Ron(rev)
*1
Short circuit detection
current
IL6,3(SC) *1
9.5
13
Unit
mΩ
16
22
mΩ
120
A
td(OC)
5
0.9
td(OC)−ton
0.65
1.6
Von(OvL)
0.65
1
3.2
2.7
20
10
IL12,3(SC)
76
50
IL12,6(SC) *1
40
IL12,12(SC) *1
10
IL18,3(SC) *1
60
IL18,6(SC) *1
50
IL18,12(SC) *1
30
IL18,18(SC) *1
Under voltage restart of
charge pump
MAX.
50
50
45
35
35
35
110
105
95
90
85
80
55
50
45
130
125
110
110
110
110
75
70
65
50
50
45
2.1
IL6,6(SC) *1
Turn-on check delay
after input current
positive slope *1
Remaining Turn-on
check delay after turn-on
time *1
Over load detection
voltage
Under voltage shutdown
TYP.
160
120
200
170
120
90
3.8
ms
VCC − VIN = 6 V,
Von = 3 V
VCC − VIN = 6 V,
Von = 6 V
VCC − VIN = 12 V,
Von = 3 V
VCC − VIN = 12 V,
Von = 6 V
VCC − VIN = 12 V,
Von = 12 V
VCC − VIN = 18 V,
Von = 3 V
VCC − VIN = 18 V,
Von = 6 V
VCC − VIN = 18 V,
Von = 12 V
VCC − VIN = 18 V,
Von = 18 V
RL = 2.2 Ω,
Tch = −40 to 150°C
1.45
V
Tch = −40 to 150°C
4.0
5.5
5.35
3.6
3.2
30
4.5
6.3
6.2
34
40
V
V
V
V
V
V
V
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
IL = 40 mA, Tch = −40 to 150°C
150
175
VCIN(CPr)
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
180
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = -40 to 150°C
ms
VCIN(Uv)
Output clamp voltage
Von(CL)
(inductive load switch
off)
Tth
Thermal shutdown
temperature *1
Note: ∗1. Not tested, specified by design
110
Test Conditions
Tch = 25°C
VCC = −12 V,
IL = −7.5 A,
Tch = 150°C
RIS = 1 kΩ
°C
Page 5 of 23
μPD166021T1F
Chapter Title
Diagnosis Function
Tch = 25°C, VCC = 12 V, unless otherwise specified
Parameter
Current sense ratio
Symbol
MIN.
TYP.
MAX.
Unit
8300
8300
8400
7500
8000
8300
7100
7700
8000
5000
5500
9200
9200
9300
9200
9300
9300
10200
10000
9800
12000
11500
11000
10600
10200
11400
10800
10400
13400
12500
12000
21000
17000
6000
11500
0.1
16000
1
μA
KILIS
Test Conditions
KILIS = IL/IIS, IIS < IIS,lim
Tch = −40°C
IL = 30A
Tch = 25°C
Tch = 150°C
IL = 7.5 A
Tch = −40°C
Tch = 25°C
Tch = 150°C
Tch = −40°C
IL = 2.5 A
Tch = 25°C
Tch = 150°C
Tch = −40°C
IL = 0.5 A
Tch = 25°C
Tch = 150°C
VIN = 0 V, IL = 0 A
Sense current offset
current
IIS,offset
Sense current under fault
condition
IIS,fault
3.5
6.0
12.0
mA
Sense current saturation
current
IIS,lim
3.5
7.0
12.0
mA
2
6
μs
Under fault conditions
8 V < VCC − VIS < 12 V,
Tch = −40 to 150°C
VIS < VOUT − 6 V,
Tch = −40 to 150°C
Tch = −40 to 150°C
0.1
0.5
μA
IIN = 0 A
700
μs
100
μs
Tch = −40 to 150°C,
IIN = 0 A IIH,
RL = 2.2 Ω
Tch = −40 to 150°C,
IL = 10A 20 A
tsdelay(fault)
Fault Sense Signal delay
*1
after short circuit detection
Sense current leakage
current
IIS(LL)
Current sense settling time
to IIS(static) after input
current positive slope *1
tson(IS)
Current sense settling time
during on condition *1
Tsic(IS)
50
Note: ∗1. Not tested, specified by design
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 6 of 23
μPD166021T1F
Chapter Title
3.6 Feature Description
3.6.1 Driving Circuit
The high-side output is turned on, if the input pin is shorted to ground. The input current is below IIH. The high-side
output is turned off, if the input pin is open or the input current is below IIL. RCC is 100 Ω TYP. ESD protection diode:
46 V TYP.
VCC
IIN
RCC
VZ,IN
0
Logic
VOUT
ZD
IN
IIN
VCC
OFF
ON
OFF
ON
0
t
Switching a resistive load
Switching lamps
IIN
IIN
0
0
IL
IL
0
0
VOUT
VOUT
VCC
0
0
IIS
IIS
0
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
t
0
IIS,lim
t
Page 7 of 23
μPD166021T1F
Chapter Title
Switching an inductive load
IIN
VCC
0
IL
0
SW1
IS
VOUT
ESD
Ris
Control
Logic
OUT
0
VON(CL)
IIS
0
t
Dynamic clamp operation at inductive load switch off
The dynamic clamp circuit works only when the inductive load is switched off. When the inductive load is switched off,
the voltage of OUT falls below 0 V. The gate voltage of SW1 is then nearly equal to GND because the IS terminal is
connected to GND via an external resister. Next, the voltage at the source of SW1 (= gate of output MOS) falls below
the GND voltage. SW1 is turned on, and the clamp diode is connected to the gate of the output MOS, activating the
dynamic clamp circuit.
When the over-voltage is applied to VCC, the gate voltage and source voltage of SW1 are both nearly equal to GND.
SW1 is not turned on, the clamp diode is not connected to the gate of the output MOS, and the dynamic clamp circuit is
not activated.
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 8 of 23
μPD166021T1F
Chapter Title
3.6.2 Short Circuit Protection
Case 1:IIN pin is shorted to ground in an overload condition, which includes a short circuit condition.
The device shuts down automatically when either or both of following conditions (a, b) is detected. The sense
current is fixed at IIS,fault. Shutdown is latched until the next reset via input.
(a) IL > IL(SC)
(b) Von > Von(OvL) after td(OC)
Case 1-(a) IL > IL(SC)
Short circuit detection
IIN
0
IL(SC)
IL
(Evaluation circuit)
0
VOUT/VCC
VCC
VCC
VBAT
IIN
Von
OUT
IN
IIS
VON
IS
VOUT
0
VBAT
VIN
VIS
VOUT
RIS IL
RL
t sdelay(fault)
IIS
: Cable impedance
IIS,fault
t
0
tsdelay(fault): Fault sense signal delay after short circuit detection
Depending on the external impedance
IL(SC): Short circuit detection current
Typical Short circuit detection current characteristics
The short circuit detection current changes according VCC voltage and Von voltage for the purpose of to be strength of
the robustness under short circuit condition.
160
150
Von = 3 V
120
IL(SC) - Load Current - A
IL(SC) - Load Current - A
140
100
VCC − VIN = 18 V
80
60
12 V
40
6V
20
120
6V
90
60
12 V
30
0
0
0
5
10
15
Von - Output Voltage - V
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
20
5
10
15
20
VCC − VIN - V
Page 9 of 23
μPD166021T1F
Chapter Title
Case 1-(b) Von > Von(OvL) after td(OC)
Short circuit detection
IIN
0
(Evaluation circuit)
IL
IL(SC)
0
VCC
IIN
VOUT/VCC
OUT
IN
IIS
IS
VCC
Von(OvL)
VBAT
0
Von
VBAT
VIN
VIS
RL
Von
VOUT
VOUT
RIS IL
: Cable impedance
td(oc)
IIS
IIS,fault
t
0
Depending on the external impedance
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
td(oc):Turn-on check delay after input current positive slope
Page 10 of 23
μPD166021T1F
Chapter Title
Case 2:Short circuit during on-condition
The device shuts down automatically when following conditions (a) is detected. The sense current is fixed at IIS,fault.
Shutdown is latched until the next reset via input. In the case of Von(NL) works such open load condition at onstate, td(OC) is expired.
(a) Von > Von(OvL) after td(OC)
Case 2-(a) Von > Von(OvL) after td(OC)
Short circuit
Short circuit detection
VIN
0
IL(SC)
(Evaluation circuit)
IL
0
VCC
VOUT
IIN
VCC
Von
OUT
IN
IIS
IS
VOUT
Von(OvL)
VBAT
VIN
VIS
RL
0
VIS
VOUT
RIS IL
: Cable impedance
td(OC)
IIS,fault
0
t
Depending on the external impedance
td(oc):Turn-on check delay after input current positive slope
IL(SC): Short circuit detection current
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 11 of 23
μPD166021T1F
Chapter Title
Over-temperature protection
The output is switched off if over-temperature is detected. Shutdown is latched until the next reset via input.
IIN
0
Tch
Tth
VOUT
0
IIS
IIS,fault
0
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
t
Page 12 of 23
μPD166021T1F
Chapter Title
3.6.3 Power Dissipation under Reverse Battery Condition
In case of reverse battery condition, internal N-ch MOSFET is turned on to reduce the power dissipation by body diode.
Additional power is dissipated by the internal resister. Following is the formula for estimation of total power dissipation
Pd(rev) in reverse battery condition.
PD(rev) = Ron(rev) x IL(rev)2
−VCC
+ (VCC − Vf − Iin(rev) x RIN) x Iin(rev)
IL(rev)
+ (VCC − Iis(rev) x RIS) x Iis(rev)
R CC
Iin(rev) = (VCC − 2 x Vf)/(RCC + RIN)
Iis(rev) = (VCC − Vf)/(RCC + Ris0 + RIS)
Ris0
IN
N-ch MOSFET
RIN
IS
The reverse current through the N-ch MOSFET has to
be limited by the connected load.
OUT
RIN < (|VCC - 8 V|)/0.08 A
RL
RIS
IIN(rev)
IIS(rev)
3.6.4 Device Behavior at Low Voltage Condition
If the supply voltage (VCC – VIN) goes down under VCIN(Uv), the device shuts down the output. If supply voltage (VCC
− VIN) increase over VCIN(CPr), the device turns on the output automatically. The device keeps off state if supply voltage
(VCC – VIN) does not increase over VCIN(CPr) after under voltage shutdown. It is assumed that VIN = 0 V when IIN is
activated.
IIN
0
IL
0
VOUT/VCC − VIN
VCC − VIN
VBAT
VOUT
VCIN(Uv)
VCIN(CPr)
0
Remark
t
It is assumed that VIN = 0 V when IIN is activated.
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 13 of 23
μPD166021T1F
Chapter Title
3.6.5 Current Sense Output
VCC
VZ,IS
RCC
RCC and Ris0 are 100 Ω (TYP.). Vz,IS = 46 V (TYP.), RIS = 1 kΩ
nominal.
ZD
IS
Iis
Ris0
Ris
IIS
Von
IIS,lim
Ron
KILIS = IL/IIS
VIS < Vout - 6 V, IIS < IIS,lim
Von(NL)
30 mV TYP.
IIS,offset
IL
IL
Current sense ratio
22000
20000
KILIS - Current Sense Ration
18000
16000
14000
Tch = −40°C
12000
10000
150°C
8000
6000
4000
0
5
10
15
20
25
30
35
IL - Load Current - A
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 14 of 23
μPD166021T1F
Chapter Title
3.6.6 Measurement Condition
Switching waveform of OUT Terminal
IIN
ton
toff
50%
dV/dton
VOUT
50%
−dV/dtoff
25%
25%
10%
Switching waveform of IS terminal
IIN
tson(IS)
tSIC(IS)
tSIC(IS)
IIS
3.6.7 Truth Table
Input Current
L
H
State
–
Normal Operation
Over-temperature or Short circuit
Open Load
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Output
OFF
ON
OFF
ON
Sense Current
IIS(LL)
IL/KILIS
IIS,fault
IIS,offset
Page 15 of 23
μPD166021T1F
Chapter Title
3.6.8 Inductive Load Switch Off Energy Dissipation for a Single Pulse
MAXIMUM ALLOWABLE LOAD INDUCTANCE for a SINGLE SWITCH OFF
IAS - Current Sense Ration - A
100
10
1
0.01
0.1
1
10
IL - Load Current - mH
The energy dissipation for an inductive load switch-off single pulse in device (EAS1) is estimated by the following
formula as RL = 0 Ω.
EAS1 = 1 I2 L
2
Von(CL)
Von(CL) − VCC
3.6.9 Maximum Allowable Switch off Energy (Single Pulse)
The harness connecting the power supply, the load and the device has a small inductance and resistance. When the
device turns off, the energy stored in the harness inductance is dissipated by the device, the harness resistance and the
internal resistance of power supply. If the current is abnormally high due to a load short, the energy stored in the
harness can be large. This energy has to be taken into consideration for the safe operation. The following figure shows
the condition for EAS2, the maximum switch-off energy (single pulse) for abnormally high current.
VCC
OUT
Lsupply
Rsupply
Lshort
IN
IS
VBAT
Rsc
RIS
RL
RSW
VBAT = 18 V,
Rsupply = 10 mΩ, Rshort = Rsc + RSW(on) = 50 mΩ,
Lsupply = 5 μH, Lshort = 15 μH,
Tch,start 150°C
: Cable resistance
: Cable inductance
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 16 of 23
μPD166021T1F
Chapter Title
3.7 Package Drawing (unit: mm)
4.0 MIN. (4.4 TYP.)
6.5±0.2
5.0 TYP.
4.3 MIN.
1.0 TYP.
5-pin TO-252 (MP-3ZK)
2.3±0.1
0.5±0.1
1.14
0.6±0.1
0 to 0.25
0.5±0.1
Note
No Plating area
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
GAUGE PLANE
SEATING PLANE
0.508
1.52±0.12
0.8
1 2 3 4 5
6.1±0.2
10.3 MAX. (9.8 TYP.)
6
Page 17 of 23
μPD166021T1F
Chapter Title
3.8 Taping Information
This is one type (E1) of direction of the device in the career tape.
Draw-out side
3.9 Marking Information
This figure indicates the marking items and arrangement. However, details of the letterform, the size and the position
aren’t indicated.
6 6 0 2 1
Pb-free plating marking
Lot code
*1
Internal administrative code
Note: *1. Composition of the lot code
Week code (2 digit number)
Year code (last 1 digit number)
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 18 of 23
μPD166021T1F
Chapter Title
REQUIRED CURRENT CAPABILITY OF INPUT
INPUT CURRENT FOR TURN OFF
SWITCH vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
500
2.5
IIL - Input current for turn-off - μA
IIH - Required current capability of Input switch - mA
4. Typical Characteristics
2
1.5
1
0.5
0
300
200
100
0
-50
0
50
100
150
200
-50
TA - Ambient Temperature - °C
0
100
150
STANDBY CURRENT
ON STATE RESISTENCE
vs. AMBIENT TEMPERATURE
vs. VCC − VIN voltage
200
14
12
12
8
4
-50
0
50
100
150
200
Ron - On-state Resistance - mΩ
16
0
10
8
6
4
2
TA = 25°C
0
0
5
TA - Ambient Temperature - °C
10
15
20
VCC − VIN - V
ON STATE RESISTANCE vs. AMBIENT
ON STATE RESISTANCE AT REVERSE BATTERY
TEMPERATURE
CONDITION vs. AMBIENT TEMPERATURE
Ron(rev) - On-state resistance at reverse
battery condition - mΩ
14
12
Ron - On-state Resistance - mΩ
50
TA - Ambient Temperature - °C
20
ICC(off) - Standby Current - μA
400
10
8
6
4
2
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
14
12
10
8
6
4
2
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
Page 19 of 23
μPD166021T1F
Chapter Title
OUTPUT CLAMP VOLTAGE (INDUCTIVE LOAD
TURN ON TIME
SWITCH OFF) vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
42
500
400
VCC − VIN = 6 V
38
ton - Turn On Time - μs
(inductive load switch off) - V
Von (CL) - Output clamp voltage
40
36
34
32
30
28
300
12 V
18 V
200
100
0
-50
0
50
100
150
200
-50
TA - Ambient Temperature - °C
50
100
150
200
TA - Ambient Temperature - °C
TURN OFF TIME
SLEW RATE ON
vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
0.6
500
VCC − VIN = 6 V
400
0.5
12 V
dV/dton - Slew rate on - V/μs
toff - Turn Off Time - μs
0
300
18 V
200
100
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
0.4
0.3
0.2
0.1
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
SLEW RATE OFF
vs. AMBIENT TEMPERATURE
0.6
−dV/dtoff - Slew rate off - V/μs
0.5
0.4
0.3
0.2
0.1
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 20 of 23
Chapter Title
SENSE CURRENT OFFSET CURRENT
SENSE CURRENT UNDER FAULT CONDITION
vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
1
0.8
0.6
0.4
0.2
0
-50
0
50
100
150
200
IIS,fault - Sense current under fault condition - mA
IIS,offset - Sense current offset current - μA
μPD166021T1F
12
10
8
6
4
2
0
-50
0
100
150
200
TA - Ambient Temperature - °C
SENSE CURRENT SATURATION CURRENT
SENSE CURRENT LEAKAGE CURRENT
vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
IIS(LL) - Sense current leakage current - μA
IIS,lim - Sense current saturation current - mA
TA - Ambient Temperature - °C
50
12
10
8
6
4
2
0
-50
0
50
100
150
0.1
0.08
0.06
0.04
0.02
0
-50
0
50
100
150
200
200
TA - Ambient Temperature - °C
TA - Ambient Temperature - °C
UNDER VOLTAGE RESTART OF CHARGE PUMP
vs. AMBIENT TEMPERATURE
vs. AMBIENT TEMPERATURE
VCIN(Uv) - Under voltage shutdown - V
6
5
4
3
2
1
0
-50
0
50
100
150
TA - Ambient Temperature - °C
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
200
VCIN(CPr) - Under voltage restart of charge pump - V
UNDER VOLTAGE SHUTDOWN
6
5
4
3
2
1
0
-50
0
50
100
150
200
TA - Ambient Temperature - °C
Page 21 of 23
μPD166021T1F
Chapter Title
5. Thermal Characteristics
TRANSIENT THERMAL RESISTANCE vs. PULSE WIDTH
rth(t) - Transient Thermal Resistance - °C/W
1000
Device on 50 mm×50 mm×1.5 mm epoxy
PCB FR4 with 6 cm2 of 70 μm copper area
Rth(ch-A) = 55°C/W
100
10
Rth(ch-C) = 3.17°C/W
1
0.1
0.001
0.01
0.1
1
10
100
1000
PW - Pulse Width - s
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 22 of 23
μPD166021T1F
Chapter Title
6. Application Example in Principle
5V
VBAT
μPD166021
Micro.
VCC
IN
OUT
*1
OUTPUT PORT
*2
R
R
OUT
IS
Load
ADC PORT
GND
RIS
Notes: *1. If output current is over the maximum allowable current for inductive load at a single switch off, or if energy at a single
switch off is over EAS1/EAS2, then a free wheeling diode must be connected in parallel the load.
*2. If current sense and diagnostic features are not used, IS terminal has to be connected to GND via resistor.
R07DS0442EJ0100 Rev.1.00
Sep 07, 2011
Page 23 of 23
μ PD166021T1F Data Sheet
Revision History
Rev.
Date
Page
1.00
Sep 07, 2011
−
Description
Summary
First Edition Issued
All trademarks and registered trademarks are the property of their respective owners.
C-1
Notice
1.
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas
Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to
be disclosed by Renesas Electronics such as that disclosed through our website.
2.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
3.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
5.
When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and
regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to
the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is
prohibited under any applicable domestic or foreign laws or regulations.
6.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
7.
Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas
Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the
use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics.
The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard":
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools;
personal electronic equipment; and industrial robots.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically
designed for life support.
"Specific":
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical
implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
9.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2011 Renesas Electronics Corporation. All rights reserved.
Colophon 1.1