Download SKY77149 数据资料DataSheet下载

DATA SHEET
SKY77149 PA Module for CDMA / PCS (1850–1910 MHz)
Applications
The SKY77149 System Smart™ Power Amplifier Module (PAM) is a fully matched 8-pin surface
mount module developed for Code Division Multiple Access (CDMA) / Personal Communications
Service (PCS) and Wireless Local Loop (WLL) applications. This small and efficient module packs full
1850–1910 MHz bandwidth coverage into a single compact package. The SKY77149 meets the
stringent spectral linearity requirements of Code Division Multiple Access (CDMA) PCS transmission,
with high power added efficiency for power output of up to 28 dBm. A low current pin (VCONT) is
provided to improve efficiency for the low RF power range of operation.
• Personal Communications
Services (PCS)
• Wireless Local Loop (WLL)
Features
• Low voltage positive bias
supply
- 3.2 V to 4.2 V
The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active
circuitry in the module. The MMIC contains on-board bias circuitry, as well as input and interstage
matching circuits. The output match is realized off-chip within the module package to optimize
efficiency and power performance into a 50-ohm load. This device is manufactured with Skyworks’
GaAs Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply
operation while maintaining high efficiency and good linearity. Primary bias to the SKY77149 is
supplied directly from a three-cell Ni-Cd, a single-cell Li-Ion, or other suitable battery with an output
in the 3.2 to 4.2 volt range. Power down is accomplished by setting the voltage on the low current
reference pin to zero volts. No external supply side switch is needed as typical “off” leakage is a few
microamperes with full primary voltage supplied from the battery.
• Low VREF
- 2.85 V, nominal
• Low IREF
- less than 1 mA
• Good linearity
• High efficiency
• Large dynamic range
• 8-pin package
- 3 x 3 x 1.2 mm
• Power down control
• Dynamic bias control
• InGaP
• IS95/CDMA2000/EVDO
• Full U.S. PCS coverage
MODULE
MMIC
VREF (1)
Skyworks offers lead
(Pb)-free "environmentally
friendly" packaging
that is RoHS compliant
(European Parliament
for the Restriction of
Hazardous Substances).
VCONT (2)
VCC2 (5)
Power
Stage Bias
Driver
Stage Bias
VCC1 (4)
RF_IN (3)
Input
Match
DA
Inter-Stage
Match
PA
Output
Match
(6) RF_OUT
GND (7, 8)
103062_001
Figure 1. Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
1
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
Electrical Specifications
The following tables list the electrical characteristics of the
SKY77149 Power Amplifier. Table 1 lists the absolute maximum
ratings, while Table 2 shows the recommended operating
conditions to achieve the performance characteristics listed in
Table 4. Table 3 presents a truth table for the power settings.
Table 1. Absolute Maximum Ratings 1
Parameter
Symbol
Minimum
Nominal
Maximum
Unit
RF Input Power
PIN
—
0
5
dBm
Supply Voltage
VCC
—
3.4
6.0
Volts
Reference Voltage
VREF
—
2.85
3.0
Volts
Control Voltage
VCONT
—
1.25
3.0
Volts
Operating TC
–30
25
+110
Storage
–55
—
+125
Case Temperature 2
TSTG
1
No damage assuming only one parameter is set at limit at a time with all other parameters set at nominal value.
2
Case Operating Temperature refers to the temperature of the GROUND PAD at the underside of the package.
°C
Table 2. Recommended Operating Conditions
Parameter
Minimum
Nominal
Maximum
Unit
PO
—
—
28.0
dBm
Operating Frequency
FO
1850.0
1880.0
1910.0
MHz
Supply Voltage
VCC
3.2
3.4
4.2
Volts
Reference Voltage
VREF
2.75
2.85
2.95
Volts
Control voltage
VCONT
1.0
1.25
2.0
Volts
Case Operating Temperature
TC
–30
+25
+85
°C
Power Output
Symbol
Table 3. Power Range Truth Table 1
VREF
VCONT
Output Power
High Power
Power Setting
2.85 V
2.0 V
28 dBm
Low Power
2.85 V
< 1.3 V
≤ 0 dBm
Shut Down
0.0 V
0.0 V
—
1
In the output power range between –10 dBm and +28 dBm, VCONT can be continuously adjusted to minimize current consumption while
meeting required linearity specification.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
2
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
DATA SHEET • SKY77149
Table 4. Electrical Specifications for CDMA Nominal Operating Conditions 1
Characteristics
Symbol
GLOW
Gain conditions
GMID
GHIGH
Gain Sensitivity
Power Added Efficiency for Optimal VCONT Setting (VCC = 3.4 V)
Total Supply current for Optimal VCONT Setting
Quiescent current
Condition
VCONT ≤ 1.3 V
PO < 0 dBm
1.3 V ≤ VCONT < 2.0 V
PO = 16 dBm
VCONT = 2.0 V
PO = 28 dBm
Minimum
Typical
Maximum
19
22
23
23
26
28
26
28
30
5
8
15
Unit
dB
GSEN
All conditions fixed, except VCONT
dB/Volt
PAELOW
PO = 0 dBm
0.5
0.7
PAEHIGH
PO = 28 dBm
37.0
40.0
ICC_LOW
PO = 0 dBm
40
60
ICC_HIGH
PO = 28 dBm
450
500
IQ_LOW
VCONT = 1.25 V
15
35
47
IQ_HIGH
VCONT = 2.0 V
65
95
130
0.5
1.5
mA
%
mA
mA
Reference Current
IREF
Control Current
ICTRL
VCONT = 2.0 V
100
250
µA
IPD
VCC = 3.4 V
VREF = 0 V
2.0
5.0
µA
ACP1_LOW
VCONT ≤ 1.3 V
PO ≤ 0 dBm
–63.0
–50.0
ACP1_HIGH PO ≤ 28 dBm
–50.0
–48.0
VCONT ≤ 1.3 V
PO ≤ 0 dBm
–80.0
–60.0
ACP2_HIGH PO ≤ 28 dBm
–55.0
–53.5
Second
FO2
–56.0
–35.0
Third
FO3
–45.0
–40.0
Total Supply current in Power-down Mode
1.25 MHz offset
Adjacent Channel Power for Optimal VCONT Setting 2,3
ACP2_LOW
1.98 MHz offset
Harmonic Suppression
dBc
PO ≤ 28 dBm
dBc
Noise Power in RX Band 1930-1990 MHz
RxBN
PO ≤ 28 dBm
–138.0
dBm/Hz
Noise Figure
NF
—
4.0
dB
Input Voltage Standing Wave Ratio (VSWR)
VSWR
—
—
2.5:1
—
Stability (Spurious output)
S
5:1 VSWR
All phases
—
–70.0
dBc
Ruggedness 4
Ru
Turn On Time 5
Turn Off Time 5
PO ≤ 28 dBm
10:1
—
PO = 29 dBm
5:1
—
DC
TONDC
40
RF
TONRF
5
DC
TOFFDC
40
RF
TOFFRF
5
VSWR
—
µs
µs
1
Per Table 2 over dynamic range up to 28 dBm output power, unless otherwise specified
2
ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.
3
For CDMA2000 test configured as [PCH @ –3.75 dB, DCCH–9600 bps @ 0 dB; SCHO–9600 bps @ 0 dB] and other test configurations that yield a peak-to-average up to 4.5 dB for CCDF = 1%,
up to 1. dB power back off from the maximum listed for IS95 may be required to meet specified maximum ACP performance under worst-case conditions.
4
All phases, time = 10 seconds; VCC = 4.2 V; Freq. = 1850 MHz, 1880 MHz, 1910 MHz; TCASE = –30 °C, +25 °C, +85 °C; PO set using 50 Ω load, PIN held constant during mismatch.
5
TONDC is time required to reach stable quiescent bias (±10%) after VREF is switched high.
TOFFDC is time required for battery to decrease to < 100 µA after VREF is switched low.
After ICQ is stable, The TONRF is time to reach final output power (±1 dB) once RF input is applied.
TOFFRF is time required for PO to drop 30 dB once RF input is removed.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
3
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
Characterization Data
The following graphs illustrate the characteristics of a typical
SKY77149 power amplifier designed for operation in the cellular
frequency band (824–849 MHz). This amplifier was selected by
characterizing a group of devices and then selecting a part with
average electrical performance for both nominal and the full
range of recommended operating conditions, including worst case
limits. Figure 2 through 8 illustrate the digital signal
characteristics of the SKY77149. Shown are power sweep
characteristics for key performance parameters, over temperature
and frequency, up to 28.5 dBm output power. The data was taken
up to and including 8 dBm output power with the bias mode
control pad setting of VCONT = 1.25 volts and from 10 dBm to
16 dBm output power with the bias mode control pad setting of
VCONT = 1.55 V. Beyond 16 dBm output power, VCONT was set
to 2.0 V.
31
29
27
Gain (dB)
25
23
VCONT = 2.0 V
21
19
VCONT = 1.55 V
VCONT = 1.25 V
17
15
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_002
Figure 2. Gain vs. Output Power
Legend
1850 MHz @ –30 ˚C
1850 MHz @ +25 ˚C
1850 MHz @ +85 ˚C
1880 MHz @ –30 ˚C
1880 MHz @ +25 ˚C
1880 MHz @ +85 ˚C
1910 MHz @ –30 ˚C
1910 MHz @ +25 ˚C
1910 MHz @ +85 ˚C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
4
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
DATA SHEET • SKY77149
800
700
600
VCONT = 2.0 V
ICC (mA)
500
VCONT = 1.55 V
400
VCONT = 1.25 V
300
200
100
0
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_003
Figure 3. Supply Current vs. Output Power
50
45
40
35
PAE (%)
30
VCONT = 2.0 V
25
20
VCONT = 1.55 V
15
VCONT = 1.25 V
10
5
0
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_004
Figure 4. Power Added Efficiency vs. Output Power
Legend
1850 MHz @ –30 ˚C
1850 MHz @ +25 ˚C
1850 MHz @ +85 ˚C
1880 MHz @ –30 ˚C
1880 MHz @ +25 ˚C
1880 MHz @ +85 ˚C
1910 MHz @ –30 ˚C
1910 MHz @ +25 ˚C
1910 MHz @ +85 ˚C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
5
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
65
VCONT = 1.25 V
VCONT = 1.55 V
VCONT = 2.0 V
60
ACPR1
55
50
45
40
35
30
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_005
Figure 5. Adjacent Channel Power Ratio 1 vs. Output Power
85
VCONT = 1.25 V
VCONT = 1.55 V
VCONT = 2.0 V
80
75
ACPR2 (dB)
70
65
60
55
50
45
40
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_006
Figure 6. Adjacent Channel Power Ratio 2 vs. Output Power
Legend
1850 MHz @ –30 ˚C
1850 MHz @ +25 ˚C
1850 MHz @ +85 ˚C
1880 MHz @ –30 ˚C
1880 MHz @ +25 ˚C
1880 MHz @ +85 ˚C
1910 MHz @ –30 ˚C
1910 MHz @ +25 ˚C
1910 MHz @ +85 ˚C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
6
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
64
DATA SHEET • SKY77149
VCONT = 1.25 V
VCONT = 1.55 V
VCONT = 2.0 V
62
60
58
2F0 (dB)
56
54
52
50
48
46
44
42
40
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_007
Figure 7. Second Harmonic vs. Output Power
65
60
VCONT = 1.25 V
VCONT = 1.55 V
VCONT = 2.0 V
3F0 (dBc)
55
50
45
40
35
30
0
2
4
6
8
10
12
14
16
18
POUT (dBm)
20
22
24
26
28
30
103062_008
Figure 8. Third Harmonic vs. Output Power
Legend
1850 MHz @ –30 ˚C
1850 MHz @ +25 ˚C
1850 MHz @ +85 ˚C
1880 MHz @ –30 ˚C
1880 MHz @ +25 ˚C
1880 MHz @ +85 ˚C
1910 MHz @ –30 ˚C
1910 MHz @ +25 ˚C
1910 MHz @ +85 ˚C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
7
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
Evaluation Board Description
The evaluation board is a platform for testing and interfacing
design circuitry. To accommodate the interface testing of the
SKY77149, the evaluation board schematic and diagrams are
1
VREF
included for preliminary analysis and design. Figure 9 shows the
basic schematic of the board for the 1850 MHz to 1910 MHz
range.
VREF
GND
VCONT
GND
8
C3
1000 pF
2
VCONT
7
C1
1000 pF
RF_IN
RF_OUT
3
4
VCC1
RF_IN
RF_OUT
VCC1
VCC2
6
5
VCC2
A C6
330 pF
C2 A
330 pF
C5
1000 pF
C4
10 µF
A Place caps at closest proximity to PA module with the capacitor grounds directly connected to the PAM grounds.
103062_009
Figure 9. Evaluation Board Schematic
P1
RF_IN
J2
SKYWORKS
SOLUTIONS, INC.
J1
C1
GND
GND
C2
VCC1
1
U1
VCONT
C3
GND
C5
VCC2
C6
VREF
GND
C4
EN17 - D435 - 001
REV. 00
06/11/03
RF_OUT
P2
COMPONENTS
C1 1000 pF
C2
330 pF
C3 1000 pF
C4
10 µF
C5 1000 pF
C6
330 pF
103062_010
Figure 10. Evaluation Board Assembly Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
8
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
DATA SHEET • SKY77149
Package Dimensions and Pin Descriptions
The SKY77149 is a multi-layer laminate base, overmold
encapsulated modular package designed for surface mount solder
attachment to a printed circuit board. Figure 11 is a mechanical
drawing of the pad layout for this package and Figure 12 is a PCB
Symbol diagram of the 3x3 mm SKY77149. Figure 13 shows the
pin names and the pin numbering convention, which starts with
pin 1 in the upper left and increments counter-clockwise around
the package. Figure 14 illustrates typical case markings.
METAL PAD EDGES
0.05 A B C
B
3
C
2X 0.4
PIN 1 INDICATOR
SOLDER MASK EDGES
0.1 A B C
METAL PAD EDGES
0.05 A B C
0.1
DETAIL A
PAD
SCALE: 2X
2X THIS ROTATION
2X ROTATED 180˚
0.1
0.1
3
SOLDER MASK EDGES
0.1 A B C
2X 0.4
1X
1X
1X
1X
DETAIL B
PAD
SCALE: 2X
THIS ROTATION
ROTATED 90˚ CCW
ROTATED 90˚ CW
ROTATED 180˚
0.1 A B C
TOP VIEW
(1.35)
2X 1.325
2X 0.7
METAL PAD
PIN 1
4X 0.4
(1.35)
A
B
4X 1.2
A
1.15 ±0.1
SOLDER MASK OPENING
0.1
4X R0.2
SIDE VIEW
0.15 A B C
BOTTOM VIEW
103062_011
ALL DIMENSIONS ARE IN MILLIMETERS.
Figure 11. SKY77149 Package Drawing
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
9
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
PCB SYMBOL FOR 3.0 x 3.0 mm PACKAGE CX77149 & CX77154 SPECIFIC
1.2
0.6
0.6
0.4
1.3
0.4
0.7
2.3
0.8 TYP
0.15
0.8 TYP
3.2
3.2
STENCIL APERTURE
TOP VIEW
APPROACH 1
COMMON GROUND
PAD
0.6
COMPONENT
OUTLINE
COMPONENT
OUTLINE
COMPONENT
OUTLINE
COMPONENT
OUTLINE
STENCIL APERTURE
TOP VIEW
APPROACH 2
0.7
4 X R0.5
0.4
0.5
0.05 ALL AROUND
2.55
0.25
0.8 TYP
0.8 TYP
0.25
3.2
METALLIZATION
Thermal Via Array
Ø0.3 mm on 0.5 mm Pitch
Additional Vias will improve
thermal performance.
NOTE: Thermal Vias Should be
Tented and Filled with Solder Mask
30-35 µm Cu Plating Recommended.
1.3
3.3
SOLDER MASK OPENING
TOP VIEW
TOP VIEW
All dimensions are in millimeters.
Figure 12. Phone PCB Layout Footprint Diagram for 3 x 3 mm, 8-Pin Package – SKY77149
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
10
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
103062_012
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
DATA SHEET • SKY77149
VREF
1
8
GND
VCONT
2
7
GND
RF_IN
3
VCC1
4
GROUND PAD
6
RF_OUT
5
VCC2
Pad layout as seen from top view looking through the package.
GROUND PAD is package underside.
103062_013
Figure 13. SKY77149 Pin Names and Configuration (Top View)
Part
Number
Pin 1
Identifier
Lot
Number
Year of
Manufacture
Week
Package
Sealed
77149-N
XXXXX.X
YYWW MX
Revision
Number
Country
Code
103062_014
details on attachment techniques, precautions, and handling
procedures recommended by Skyworks, please refer to Skyworks
Application Note: PCB Design and SMT Assembly/Rework,
Document Number 101752. Additional information on standard
SMT reflow profiles can also be found in the JEDEC Standard
J-STD–020.
Production quantities of this product are shipped in the standard
tape-and-reel format. For packaging details, refer to Skyworks
Application Note: Tape and Reel Information – RF Modules,
Document Number 101568.
Electrostatic Discharge Sensitivity
The SKY77149 is a Class 2 device. Figure 15 lists the Electrostatic
Discharge (ESD) immunity level for each non-ground pin of the
SKY77149 product. The numbers in Figure 15 specify the ESD
threshold level for each pin where the I-V curve between the pin
and ground starts to show degradation.
The ESD testing was performed in compliance with
MIL-STD-883E Method 3015.7 using the Human Body Model. If
ESD damage threshold magnitude is found to consistently exceed
2000 volts on a given pin, this so is indicated. If ESD damage
threshold below 2000 volts is measured for either polarity,
numbers are indicated that represent worst case values observed
in product characterization.
Various failure criteria can be utilized when performing ESD
testing. Many vendors employ relaxed ESD failure standards,
which fail devices only after “the pin fails the electrical
specification limits” or “the pin becomes completely nonfunctional”. Skyworks employs most stringent criteria and fails
devices as soon as the pin begins to show any degradation on a
curve tracer.
Figure 14. Typical Case Markings
Package and Handling Information
Because of its sensitivity to moisture absorption, this device
package is baked and vacuum-packed prior to shipment.
Instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken,
otherwise, problems related to moisture absorption may occur
when the part is subjected to high temperature during solder
assembly.
The SKY77149 is capable of withstanding an MSL3/250 °C solder
reflow. Care must be taken when attaching this product, whether
it is done manually or in a production solder reflow environment.
If the part is attached in a reflow oven, the temperature ramp rate
should not exceed 3 °C per second; maximum temperature
should not exceed 250 °C. If the part is manually attached,
precaution should be taken to insure that the part is not subjected
to temperatures exceeding 250 °C for more than 10 seconds. For
VREF
> + 2 kV
< – 2 kV
VCONT
> + 2 kV
< – 2 kV
RF_IN
> + 2 kV
< – 2 kV
VCC1
> + 2 kV
< – 2 kV
1
8
GND
2
7
GND
3
6
4
GROUND PAD
5
RF_OUT
> + 2 kV
< – 2 kV
VCC2
> + 2 kV
< – 2 kV
Pad layout as seen from top view looking through the package.
103062_015
Figure 15. ESD Sensitivity Areas (Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
www.BDTIC.com/Skyworks
103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006
11
DATA SHEET • SKY77149
PA MODULE FOR CDMA / PCS (1850–1910 MHz)
To avoid ESD damage, both latent and visible, it is very important
that the product assembly and test areas follow the Class-1 ESD
• Personnel Grounding
- Wrist Straps
- Conductive Smocks, Gloves and Finger Cots
- Antistatic ID Badges
• Protective Workstation
- Dissipative Table Top
- Protective Test Equipment (Properly Grounded)
- Grounded Tip Soldering Irons
- Solder Conductive Suckers
- Static Sensors
handling precautions listed below.
• Facility
- Relative Humidity Control and Air Ionizers
- Dissipative Floors (less than 109 Ω to GND)
• Protective Packaging and Transportation
- Bags and Pouches (Faraday Shield)
- Protective Tote Boxes (Conductive Static Shielding)
- Protective Trays
- Grounded Carts
- Protective Work Order Holders
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
12
www.BDTIC.com/Skyworks
November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B
Ordering Information
Model Number
Manufacturing Part
Number
SKY77149
SKY77149
Product Revision
Package
Operating Temperature
3x3LM–10
–30 °C to +85 °C
Revision History
Revision
Level
Date
Description
A
May 8, 2006
Initial Release
B
November 6, 2006
Revise: Table 4
References
Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752.
Application Note: Tape and Reel Information – RF Modules, Document Number 101568
Standard SMT Reflow Profiles: JEDEC Standard J–STD–020
Copyright © 2003–2006, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be
used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products,
specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts,
incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of
Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions.
THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS
INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER
INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST
REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their
own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
The following are trademarks of Skyworks Solutions, Inc.: Skyworks®, the Skyworks logo, and Breakthrough Simplicity®. Product names or services listed in this publication are for identification
purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at
www.skyworksinc.com, is incorporated by reference.
www.BDTIC.com/Skyworks