Download Hardware Graduation Project (2) Seminar

Hardware Graduation Project (2)
Seminar
Prepared by :
Belal Mazen Qaddara
Mohammed Wajeeh Abu Aisha
Outline
Project abstract view and features .
Mechanical Part of “iLock “system.
Electrical and Electronic Part in “iLock” system.
“iLock” system more and more.
Demo and Show.
What is iLock ?!
 iLock is Keyless entry using Phone or PC .
 iLock is Keyless entry by typing password to built in
keypad and LCD on the door.
 iLock is Key entry using traditional methods.
 iLock lets you Lock or unlock your door from any where in
the world.
 iLock lets you to see if your door is locked or not and
opened or not when you’re gone.
Cont.
 iLock will send a notification when anyone lock or unlock
the door using phone or Pc or Keypad.
 iLock send SMS messages and notification when
someone knocks on your door.
 iLock connect to the internet via Wi-Fy module.
 iLock connect to any smartphone via Bluetooth as well
as via wifi wireless network.
 iLock connect to GSM network thanks to GSM Module.
iLock System’s blocks
Mechanical View for iLock system
 Because iLock is keyless or key entry. We
need the deadbolt support this feature .
 This is the first challenge in our Project.
 Now we must find the deadbolt that easily
interface with motor without change of the
normal behavior for normal deadbolts.
The Normal Deadbolt
The customized deadbolt
Cont.
The Prototype Door
The door that we designed for the iLock Project is
a prototype door to apply the required features .
 The Door has following characteristics:
1. Dimensions of the iLock System are 70*50 cm
2. The door was designed using iron metal
3. Door Cover made from Aluminum
The Door’s Design
The Electronics and Electrical Part
Microcontroller
 ilock’s system use Arduino Mega 2560 which is based on
the ATmega2560 AVR microcontroller.
 The main feature for this which is support multi hardware
serial pins and of course multi software serial .
Cont.
The Arduino Mega 2560 has
1. 54 digital input/output pins (of which 14 can be
used as PWM outputs).
2. 16 analog inputs.
3. 4 UARTs (hardware serial ports).
4. a 16 MHz crystal oscillator, a USB connection, a
power jack, an ICSP header, and a reset button.
Wireless Module
iLock connect to the internet via wireless wifi
module.
We use RN-XV Wi-Fly module .
The RN-XV module is based upon Roving
Networks' robust RN-171 Wi-Fi module.
1. Incorporates 802.11 b/g radio .
2. 32 bit processor, TCP/IP stack, real-time clock,
crypto accelerator, power management unit and
analog sensor interface.
In the simplest configuration, the hardware only
requires four connections (PWR, TX, RX and
GND) to create a wireless data connection.
How we configure Wi-Fly Module ?!
 At first stage , this module operates on 3.3
voltage and so we use regulated breakout that
support 3.3 voltage for all input (Pwr,TX,RX) of
Wifly module .
But it was nightmare , we found this breakout
isn’t compatible with RN-171 wifly.
 Now we must configure wifly module in order
to connect local wireless network.
 We built the following circuit that interface
our computer serially and entering command
mode for this module .
We configure the wifly module using specific
commands from it datasheet .
 We make it able to associate wireless Access
point, after that it take an ip address , DNS ,
GW.
Interface Wifly module to MCU
 The interface circuit for MCU is the same for
interfacing PC .
MCU send data serially to wifly module by hiring
software serial pins .
Wifly module now can post or get data to the
webserver on the internet and vice versa passing
received data to MCU.
How iLock operate in the internet
Bluetooth Module
 iLock uses Bluetooth communication to
connect any smartphone to lock or unlock
your door.
We use RN-41 Bluetooth model from Roving
Network.
Cont.
 We interface Bluetooth module to MCU so it
receive and send data serially to MCU using
Hardware serial .
How iLock operate via Bluetooth
GSM Module
GSM in iLock:
+
ATmega328 MCU
=
GSM Sm5100B
GSM arduino shield
Cont.
LCD and Keypad
 iLock built in LCD and Keypad interfaced to
MCU allows user to type specific password
then posted to webserver via HTTP protocol to
lock or unlock your door.
Webserver application do the validation.
 LCD also print the status of the door.
The Motor
 The main and first consideration of iLock system .
We used Central Door Locking that available in cars
and vehicles doors.
It comes with five wires:
1.
2.
3.
4.
5.
Power wire (12 volt).
Ground.
Normally open with ground.
Normally close with ground .
The common between NO and NC.
 the output signal is on/off switching
State.
How we interface the motor to MCU ?
Shock Sensor
 iLock system detect if someone knocking on the
door or not .
To implement this feature we use shock sensor
that available for car alarm system.
This sensor operates on 12 volt. And the signal
given is analog signal that interfaced to voltage
divider to transform it to range (0-5 volt).
The output signal inserted to ADC that available
in MCU .
The main advantage for this sensor we can tune
the sensitivity .
MCU detect via given threshold to determine if
someone knocking or not .
Dry contact switch sensor
This sensor is used to know if you’re door is
open or close .
It based on magnetic field between two
pieces . If the are adjacent the Dry sensor will
close it circuit and give the MCU input signal
(Switching on/off) signal .
Demo And Show