Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Pointing and Stabilization of Lightweight Balloon Borne Telescopes presented at the SwRI LCANS 09 Balloon Workshop on Bridging the Gap To Space Lightweight Science Payloads on High-Altitude Long-Duration Balloons and Airships 26 October 2009 Larry Germann Left Hand Design Corporation 1 The Purpose of a Precision Pointing System • • • • • Perform line-of-sight stabilization – Correct atmospheric turbulence – Correct vehicle base motion – Correct vibration of optical elements – Correct force or torque disturbances – Correct friction-induced pointing errors Perform scanning function to extend the Field of Regard beyond the telescope’s Field of View Perform chopping function Perform dither function Quickly slew and stare among a field of targets 2 When a Precision Pointing System is Needed • When the required pointing stability cannot be achieved by the platform attitude control system • When the field-of-regard requirement is larger than the instrument’s achievable field-of-view • When chopping is required to calibrate the optical sensor 3 Precision Pointing Systems Cover Large Ranges of Precision and Field-of-Regard • • Fields-of-Regard from 100 microradian to continuous rotation are considered. Precision is defined as positioning resolution, stability and following accuracy. Friction Limit Fine-Steering Mechanism (FSM) with a Coarse Steering Mechanism 1000 100 10 1 0.001 Mass-Stabilized Telescope Satellite, like HST FSM Sensor Noise Limit with 10x Optical Gain Field of Regard (+- milliradians) 10000 0.01 Coarse-Steering Mechanism Single Full-Aperture Flexure-Mounted Steering Mirror Full-Aperture FSM Sensor Noise Limit 0.1 Single Full- or Reduced-Aperture Flexure-Mounted Steering Mirror 1 10 100 System Precision (micro-radians) 4 Line-Of-Sight Stabilization, Stability Correction Ratio Pointing System Cost is Related to the Correction Ratio Spectrum 60 Pointing 40 Correction Ratio Amplitude (dB) 20 0 10 Readily Available Currently Achievable In Development Not Possible 20 50 100 200 500 1000 Frequency (Hz) Correction Ratio Amplitude (f) = Base Motion (f) / Residual LOS Jitter Requirement (f) 5 Dominant Sources of Vehicle Base Motion • LEO Spacecraft – Thermal Shock from Transitions into & from Umbra – Attitude Control System (ACS) exciting vehicle bending modes – Solar Array Drives • High-Altitude Lighter-Than-Air – ACS exciting pendulum & suspension cable bending modes – Payload Mechanisms – Station-Keeping Propulsion, if applicable • High-Altitude Heavier-Than-Air – Air Turbulence exciting vehicle bending modes – Propulsion 6 Typical Precision Pointing System Components • • • • The components of a typical precision pointing system include: – Beam-expander telescope – Fine-steering mechanism or fast-steering mechanism: two-axis reducedaperture, full-aperture steering mirror or isolation system – Coarse-pointing mechanism: vehicle attitude control system, two-axis gimbaled telescope or full-aperture steering mirror Payload motion sensor suite: inertially or optically referenced In general, both fine-and course-pointing mechanisms are required when system dynamic range >10^5 @1kHz or >10^6 @10Hz is required, exceptions include a mass-stabilized satellite ACS for the single pointing stage Flexure-mounted fine-steering mechanism is required when system following accuracy requirement exceeds friction- or hysteresis-induced limits 7 Fine- and CoarsePointing Mechanisms • • Coarse-Pointing Mechanism – Performs large-angle motions – Can be vehicle ACS or a bearing-mounted mechanism – Keeps FPM near the center of its travel range Fine-Pointing Mechanism – Performs high-frequency portions of pointing motions – Performs high-acceleration motions – Accurately follows commands – Corrects or rejects base motion and force and torque disturbances – Can be reaction-compensated (a.k.a. momentum compensated) 8 2-Axis Fast-Steering Mechanism Technology is Mature • • • • Apertures for beam sizes from 15mm to 300mm are available, 116 x 87mm for a 75mm beam shown -3dB closed-loop servo control bandwidth up to 5,000 Hz Range of travel up to +-175mrad (+-10degrees) is available A variety of mirror substrate materials are proven – Aluminum – Beryllium (shown here) – Silicon Carbide – Silicon Carbide Foam – Zerodur – BK-7 9 CE50-35-CV-RC2 FSM Is Simple, Robust and Mature •The CE75-35-BK SN140 •BK-7 mirror •76.2mm diameter aperture •+-35mRad travel •120 Rad/Sec2/rootW efficiency •2,300 Rad/Sec2 acceleration •wave PV @633nm surface figure error •450 Hz -3dB closed-loop servo control bandwidth 10 CE75-35-ZD Represents LHDC’s line of Cost-Effective FSM •CE75-35-ZD SN147, Zerodur mirror •76.2mm diameter aperture •+-26mRad travel •A custom abbreviated frame •9,000 Rad/Sec2 acceleration •120 Rad/Sec2/rootW efficiency •0.165 wave PV @633nm surface figure error •250 Hz -3dB closed-loop servo control bandwidth •Coating is highly reflective at 1.5um 11 FO50-175-AL Has Space-Flight Experience •FO50-175-AL SN106 •Aluminum mirror •80.7 x 60mm polished aperture •+-175mrad travel •380 Hz -3dB closed-loop servo control bandwidth •7,000 Rad/Sec2 acceleration •Proven in low-earth orbit 12 FO50-35-SC-RT7 Achieves Record Servo Control Bandwidth •FO50-35-SC-RT7 SN133 •Silicon carbide mirror •80.7 x 60mm polished aperture •+-5mrad travel with the reduced-travel option •5,000 Hz -3dB closed-loop servo control bandwidth when base-referenced •6,000 Hz -3dB closed-loop servo control bandwidth when optically referenced •3,300 Rad/Sec2 acceleration 13 The Fine-Steering Mechanism Can Be An Active Isolation System Non-Contacting 6-DOF Active Isolation System • Non-Contacting electromagnetic actuators • Non-Contacting sensors • Highly flexible umbilical transfers signals with <0.1 Hz suspension resonant frequency – minimal transfer of base motion forces • Accelerometer- and position-referenced stabilization servos • IS2-10 Isolation System – Occupies a 25mm thick disk – ±2mm travel in 3 axes • IS5-40 Isolation System used here as a base-motion simulator – ±5mm travel in 3 axes 14 Servo Functional Block Diagram Pointing/Tracking Error (2) Tra cking Position Command (2) Tra cking Position Error (2) 1st Base Referenced Position Command (2) 2nd Base Referenced Position Command (2) Feed-Forward Acceleration Command (2) + + + + - Tra ck Point Position Servo Compensation + + Current Driver Electronics Fine-Steering Mirror Mechanism Thermal Sensor (2) Base Referenced Position Sensor Output (2) Tra cking Optical Sum Tra ck Enable Position Sensor Demodulation Point/Track Switching Logic 15 Flight-Format Servo Control Electronics is Available • • • • • SC03-BD 2 Channels Servo Control – Position-Referenced Loops – Current-Referenced Drivers – Optical Tracking Reference – Position Sensor Reference Light Weight – 150 Grams Full Military Temperature Up to +-45V, 10A Driver Capability 16 Servo Control Electronics Available in a VME-6U Single-Card Format SC02-BD Single-Card VME-6U Format Contains All Servo Functions - Pointing and Tracking Modes - Current-Referenced Driver - High-Temperature Driver Shutdown 17 Components of Pointing Accuracy • Fine- and course-steering mechanism pointing accuracy is defined in several ways: – Positioning resolution and position reporting resolution – Line-of-sight jitter and position reporting noise – Short-term positioning drift and position reporting drift – Long-term positioning drift and position reporting drift – Positioning thermal sensitivity and position reporting thermal sensitivity – Positioning linearity and position reporting linearity 18 Imaging Resolution Limit is Related to Altitude and Aperture • • Imaging resolution is constrained by the optical diffraction limit, which is a function of altitude and telescope aperture Image resolution is defined as a distance on the ground from 30km altitude Diffraction-Limited Resolution as a Function of Aperture and Wavelength 100 10 DiffractionLimited 1 Resolution (m on ground at 30km altitude) 0.1 50 0.01 100 100 200 30 10 3 Wavelength (micron) 400 1 0.3 0.1 Aperture (mm) 19 Positioning and Reporting Linearity • Positioning linearity is defined as the difference between commanded and achieved position over the operating ranges of travel and temperature – Dominated by friction, disturbances and position sensor error – Position sensor error is dominated by thermal sensitivity – Typically not much better than 0.04% of travel • Reporting linearity is the difference between reported and achieved position over the operating ranges of travel and temperature – Dominated by position sensor error 20 Fast Beam Steering is Defined as Servo Control Bandwidth Fast beam steering is defined as the ability to follow a small-amplitude sine wave at various frequencies 10000 Servo Control Bandwidth (Hz) • Servo Control Bandwidth vs. Aperture and Travel for Fine-Steering Mirrors 1000 100 224 153 Major Axis Aperture (mm) +-10 mR +-35mR +-175mR 116 80 56 Travel 10 Alternately defined as the 0dB open-loop frequency +-10 mR Extended +-35mR Extended +-175mR Extended 40 • Generally defined as the frequency at which the closed-loop servo response falls by 3dB 24 • 21 Fast Beam Steering is also Defined as Acceleration Capability • • Fast Beam Steering is sometimes defined as the highest frequency at which the mechanism can perform a full travel sine wave This is limited by the mechanism’s acceleration capability Acceleration is shown here in terms of peak and continuous capability 100000 Acceleration (Rad/Sec2) • Peak and Continuous Acceleration Capability vs. Aperture and Substrate Material for Fine-Steering Mirrors 10000 SiC Peak Be Peak Al & Zd Peak Substrate Material 1000 24 40 56 80 116 153 Major Axis Aperture (mm) 224 SiC Continuous Be Continuous Al & Zd Continuous 22 Non-Linear Characteristics Limit Positioning Accuracy • Friction-induced pointing error – Typically associated with ball or sleeve bearings – Peaks at turn-around condition (stick-slip) – Friction-induced error amplitude can be readily estimated • Peak Pointing Error ~ 2 * Friction Torque / Inertia / Bandwidth2 • Hysteresis-induced pointing error – Typically associated with ceramic actuators – Typically quantified in terms of % of travel range – Effect are similar to friction effects 23 Precision Pointing Systems Offer Many Benefits • • • • Extended Dynamic Range, – Up to 9 orders of magnitude – Up to +-180 degree Field of Regard – As low as nanoradian line-of-sight stability High servo control bandwidth, up to 5,000 Hz – Correct disturbances up to 1,000 Hz Stable Line-of-Sight – Correct for platform vibrations – Correct for aero turbulence Agile Beam-Steering for scanning, chopping, dither, etc. – Up to 15,000 rad/sec2 acceleration – Up to 30 rad/sec rate 24 Many Precision Pointing Instruments are Suitable for Near-Space Platforms • • • • • • LIDAR measurements of forest canopy LIDAR measurements of foliage, carbon stock under canopy LIDAR measurements of targets under foliage or camouflage LIDAR topology measurements under foliage 0.1m resolution over a 20km circle on ground from 100km altitude 0.03m resolution over a 6km circle on ground from 30km altitude 25