Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Light Light n2 Light Light n2 n1 > n 2 A planar dielectric waveguide has a central rectangular region of higher refractive index n 1 than the surrounding region which has a refractive index n2 . It is assumed that the waveguide is infinitely wide and the central region is of thickness 2 a. It is illuminated at one end by a monochromatic light source. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) n2 B E Light A k1 n 1 d = 2a C y x z n2 A light ray travelling in the guide must interfere constructively with itself to propagate successfully. Otherwise destructive interference will destroy the wave. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) n2 A B 1 E k1 2 A C y n1 n2 2a x 1 z B Two arbitrary waves 1 and 2 that are initially in phase must remain in phase after reflections. Otherwise the two will interfere destructively and cancel each other. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) n2 A 1 E Guide center C a y k A 2 a y y z x Interference of waves such as 1 and 2 leads to a standing wave pattern along the ydirection which propagates along z. © 1999 S.O. Kasap,Optoelectronics (Prentice Hall) Fie ld of evanescent wave (exponential decay) y n2 Field of guided wave E(y,z,t) = E(y)cos(t – 0z) E(y) Light m=0 n1 n2 The electric field pattern of the lowest mode traveling wave along the guide. This mode has m = 0 and the lowest . It is often referred to as the glazing incidence ray. It has the highest phase velocity along the guide. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) y n2 E(y) Cl addi ng m= 1 m= 0 Core n1 n2 m= 2 2a Cl addi ng The electric field patterns of the first three modes (m = 0, 1, 2) traveling wave along the guide. Notice different extents of field penetration into the cladding. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) High order mode Light pulse Low order mode Broadened light pulse Cladding Core Intensity Intensity Axial 0 Spread, t Schematic illustration of light propagation in a slab dielectric waveguide. Light pulse entering the waveguide breaks up into various modes which then propagate at different group velocities down the guide. At the end of the guide, the modes combine to constitute the output light pulse which is broader than the input light pulse. © 1999 S.O. Kasap,Optoelectronics (Prentice Hall) t (a) TE mode B // By (b) TM mode E // Ey y Bz O E Ez B z x (into paper) Possible modes can be classified in terms of (a) transelectric field (TE) and (b) transmagnetic field (TM). Plane of incidence is the paper. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) tan(ak1cosm m/2) m = 1, odd m = 0, even f(m) 10 89.17 5 88.34 c 87.52 86.68 m 0 82 84 86 88 90 Modes in a planar dielectric waveguide can be determined by plotting the LHS and the RHS of eq. (11). © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Slope = c/n 2 Slope = c/n 1 TE2 TE1 cut-off TE0 m Schematic dispersion diagram, vs. for the slab waveguide for various TEm. modes. cut–off corresponds to V = /2. The group velocity vg at any is the slope of the vs. curve at that frequency. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) y y Cladding 2 > 1 1 > c v g1 1 < cut-off E(y) Core v g2 > v g1 2 < 1 Cladding The electric field of TE 0 mode extends more into the cladding as the wavelength increases. As more of the field is carried by the cladding, the group velocity increases. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) y y Cl addi ng Core n2 n1 r z Fiber axis n The step index optical fiber. The central region, the core, has greater refractive index than the outer region, the cladding. The fiber has cylindrical symmetry. We use the coordinates r, , z to represent any point in the fiber. Cladding is normally much thicker than shown. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Along the fiber 1 1, 3 3 (a) A meridional ray always crosses the fiber axis. Meridional ray Fiber axis 2 2 1 2 1 Skew ray Fiber axis 5 3 5 4 Ray path along the fiber 4 2 3 (b) A skew ray does not have to cross the fiber axis. It zigzags around the fiber axis. Ray path projected on to a plane normal to fiber axis Illustration of the difference between a meridional ray and a skew ray. Numbers represent reflections of the ray. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) (a) The electric field (b) The intensity in of the fundamental the fundamental mode mode LP01 (c) The intensity (d) The intensity in LP 11 in LP 21 Core E Cladding E01 r The electric field distribution of the fundamental mode in the transverse plane to the fiber axis z. The light intensity is greatest at the center of the fiber. Intensity patterns in LP 01, LP11 and LP21 modes. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) b 1 LP 01 0.8 LP 11 0.6 LP 21 0.4 LP 02 0.2 0 V 0 1 2 3 2.405 4 5 6 Normalized propagation constant b vs. V-number for a step index fiber for various LP modes. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Lost n2 n0 n1 < c B Cladding Propagates > c A Fiber axis max Core A B max © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Maximum acceptance angle max is that which just gives total internal reflection at the core-cladding interface, i.e. when = max then = c. Rays with > max (e.g. ray B) become refracted and penetrate the cladding and are eventually lost. Cladding Input v g ( 1 ) Emitter Very short light pulse v g ( 2 ) Intensity Intensity Core Output Intensity Spectrum, ² Spread, ² 1 o 2 0 t All excitation sources are inherently non-monochromatic and emit within a spectrum, ² , of wavelengths. Waves in the guide with different free space wavelengths travel at different group velocities due to the wavelength dependence of n1. The waves arrive at the end of the fiber at different times and hence result in a broadened output pulse. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) t Dispersion coefficient (ps km -1 nm -1 ) 30 Dm 20 10 Dm + Dw 0 0 -10 Dw -20 -30 1.1 1.2 1.3 1.4 (m) 1.5 1.6 Material dispersion coefficient (Dm) for the core material (taken as SiO2 ), waveguide dispersion coefficient (Dw ) (a = 4.2 m) and the total or chromatic dispersion coefficient Dch (= Dm + Dw ) as a function of free space wavelength, © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Intensity t Output light pulse n1 y // y n1 x // x Ey Ex Core Ex z Ey = Pulse spread t E Input light pulse Suppose that the core refractive index has different values along two orthogonal directions corresponding to electric field oscillation direction (polarizations). We can take x and y axes along these directions. An input light will travel along the fiber with Ex and Ey polarizations having different group velocities and hence arrive at the output at different times © 1999 S.O. Kasap,Optoelectronics (Prentice Hall) -1 Dispe rsion coefficient (ps km nm -1) n 30 20 r Dm 10 0 2 1 Dch = Dm + Dw -10 Dw -20 Thin laye r of c ladding with a de pressed index -30 1.1 1.2 1.3 1.4 (m) 1.5 1.6 1.7 Dispersion flattened fiber example. The material dispersion coefficient ( Dm) for the core material and waveguide dispersion coefficient ( Dw) for the doubly clad fiber result in a flattened small chromatic dispersion between 1 and 2. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Dispersion coefficient (ps km-1 nm-1) 20 Dm 10 SiO2-13.5%GeO2 0 a (m) Dw 4.0 3.5 3.0 –10 2.5 –20 1.2 1.3 1.4 1.5 1.6 (m) Material and waveguide dispersion coefficients in an optical fiber with a core SiO 2-13.5%GeO2 for a = 2.5 to 4 m. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Fiber Digital signal Information Emitter t Photodetector Information Input Output Input Intensity Output Intensity ² Very short light pulses 0 T t t 0 ~2² An optical fiber link for transmitting digital information and the effect of dispersion in the fiber on the output pulses. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Output optical power T = 4 1 0.61 0.5 t A Gaussian output light pulse and some tolerable intersymbol interference between two consecutive output light pulses (y-axis in relative units). At time t = from the pulse center, the relative magnitude is e -1/2 = 0.607 and full width root mean square (rms) spread isrms = 2. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Electrical signal (photocurrent) 1 0.707 Fiber Sinusoidal signal Photodetector Emitter t Optical Input f = Modulation frequency Pi = Input light power Optical Output Po = Output light power 1 kHz 1 MHz 1 GHz 1 MHz 1 GHz f fel Sinusoidal electrical signal Po / Pi 0.1 0.05 0 t 0 t 1 kHz fop f An optical fiber link for transmitting analog signals and the effect of dispersion in the fiber on the bandwidth, fop. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) n2 n1 3 2 1 O n (a) Multimode step index fiber. Ray paths are different so that rays arrive at different times. n2 O O' O'' 3 2 1 2 3 n1 n2 © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) n (b) Graded index fiber. Ray paths are different but so are the velocities along the paths so that all the rays arrive at the same time. (a) TIR n decreases step by step from one layer to next upper layer; very thin layers. (b) TIR Continuous decrease in n gives a ray path changing continuously. (a) A ray in thinly stratifed medium becomes refracted as it passes from one layer to the next upper layer with lower n and eventually its angle satisfies TIR. (b) In a medium where n decreases continuously the path of the ray bends continuously. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) nc B' B 2 O 1 B B' c/nb c/na B' Ray 2 A B'' nb na A Ray 1 M © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) We can visualize a graded index fiber by imagining a stratified medium with the layers of refractive b indices na > nb > nc ... Consider two close rays 1 and 2 launched from O at the same time but with slightly a different launching angles. Ray 1 just suffers total internal reflection. O' Ray 2 becomes refracted at B and reflected at B'. c A solid with ions Ex Light direction k z Lattice absorption through a crystal. The field in the wave oscillates the ions which consequently generate "mechanical" waves in the crystal; energy is thereby transferred from the wave to lattice vibrations. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) A dielectric particle smaller than wavelength Incident wave Through wave Scattered waves Rayleigh scattering involves the polarization of a small dielectric particle or a region that is much smaller than the light wavelength. The field forces dipole oscillations in the particle (by polarizing it) which leads to the emission of EM waves in "many" directions so that a portion of the light energy is directed away from the incident beam. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Field distribution Microbending Escaping wave Cladding Core c R Sharp bends change the local waveguide geometry that can lead to waves escaping. The zigzagging ray suddenly finds itself with an incidence angle that gives rise to either a transmitted wave, or to a greater cladding penetration; the field reaches the outside medium and some light energy is lost. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) B (m-1) for 10 cm of bend = 633 nm V 2.08 = 790 nm V 1.67 0 2 4 6 8 10 12 14 16 18 Radius of curvature (mm) Measured microbending loss for a 10 cm fiber bent by different amounts of radius of curvature R. Single mode fiber with a core diameter of 3.9 m, cladding radius 48 m, = 0.00275, NA = 0.10, V 1.67 and 2.08 (Data extracted and replotted from A.J. Harris and P.F. Castle, IEEE J. Light Wave Technology, Vol. LT14, pp. 34-40, 1986; see original article for discussion of peaks in B vs. R at 790 nm). From S.O. Kasap, Optoelectronics and Photonics: Principles and Practices (Prentice Hall) r Buffer tube: d = 1mm Protective polymerinc coating Cladding: d = 125 - 150 m n Core: d = 8 - 10 m n1 n2 The cross section of a typical single-mode fiber with a tight buffer tube. (d = diameter) © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) Drying gas es Porous soot preform wit h hole Vapors: SiCl 4 + GeCl 4 + O 2 Fuel: H 2 Furnace Preform Burner Furnace Depos it ed s oot Target rod Depos it ed Ge doped SiO 2 Rotate mandrel (a) (b) Clear s olid glas s preform (c) Drawn fiber Schematic illustration of OVD and the preform preparation for fiber drawing. (a) Reaction of gases in the burner flame produces glass soot that deposits on to the outside surface of the mandrel. (b) The mandrel is removed and the hollow porous soot preform is consolidated; the soot particles are sintered, fused, together to form a clear glass rod. (c) T he consolidated glass rod is used as a preform in fiber drawing. © 1999 S.O . Kasap,Optoelectronics (Prentice Hall) vg (m/s) c/n2 TE 0 TE 4 TE 1 c/n1 (1/s) cut-off Group velocity vs. angular frequency for three modes for a planar dielectric waveguide which has n1 = 1.455, n2 = 1.44, a = 10 m (Results from Mathview, Waterloo Maple math-software application). T E0 is for m = 0 etc. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) 1.5 1 V[d2(Vb)/dV2] 0.5 0 0 1 2 3 V - number [d2(Vb)/dV2] vs. V-number for a step index fiber (after W.A. Gambling et al., The Radio and Electronics Engineer, 51, 313, 1981) © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) y = 5/2 n3 Medium 3 B' B' B' n2 B Ray B O n1 y = 3/2 B' Medium 2 A B Ray A A A Medium 1 B ' B'' B O' y = /2 /2 y=0 Step-graded-index dielectric waveguide. Two rays are launched from the center of the waveguide at O at angles A and B such that ray A suffers TIR at A and ray B suffers TIR at B'. Both TIRs are at critical angles. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall) 0.25P 0.5P O' O O O (a) 0.23P (b) (c) Graded index (GRIN) rod lenses of different pitches. (a) Point O is on the rod face center and the lens focuses the rays onto O' on to the center of the opposite face. (b) The rays from O on the rod face center are collimated out. (c) O is slightly away from the rod face and the rays are collimated out. © 1999 S.O. Kasap, Optoelectronics (Prentice Hall)