Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Digital Radiography Or Things they never tell you when the equipment is installed REV 11/2008 Computed Radiography Fundamentals of Computerized Radiography Imaging Plates Latitude and Contrast – Independent functions – Contrast is dependent on look-up table (LUT) and final image processing Image appearance not as closely related to exposure factor selection as F/S was – Except when extremely out of range IMAGE READING EDR Exposure Data Recognition When laser scans it is looking for area of plate that has exposure Some read from center out and look for two sides of collimation Works best when image centered Histogram Identifies all densities on plate A graph that displays signal value x-axis related to amount of exposure y-axis displays number of pixels for each exposure Series of peaks and valleys Pattern varies for each body part Histogram Location Example of a chest histogram X-ray energy and absorption effects – Low kVp, large differences (high contrast) – High kVp, small differences (low contrast) Different energies superimposed Different doses (mAs), same kVp Darker Lighter Histogram showing pixel values in an image. The pixel values in gray are on the horizontal with the total number for each on the vertical. Histogram Analysis Collimation is very important If plate reader cannot find collimated edges then all the exposure on plate will be included in the histogram Histogram from plate is compared to body part histogram stored in computer Characteristic curve & histogram Underexposed Overexposed Just right! LUT Look Up Table (LUT) Each anatomic area has a LUT Used to adjust contrast and density Other terms that may be used for this – Contrast rescaling – Contrast processing – Gradation processing – Tone scaling LUT The image data from the histogram is rescaled for application of the LUT The LUT maps the adjusted data through a “S” curve that is similar to an H & D curve The result is an image that has the correct contrast and brightness (density) 1. is unprocessed, 2. algorithm finds anatomy, 3. finished LOOK UP TABLE (LUT) Linear LUT Black Saturation White Saturation Black Shirt Facial Tones * No Detail in Black Areas * High Contrast * Only Detail in White Areas can be seen * No Detail in White Areas * Low Contrast * Only Detail in Black Areas can be seen Exposure Indicators Imaging plates get a signal from the exposure they receive The value of the signal is calculated from the region identified as the anatomy of interest The signal for the plate is an average of all signals given to the plate The total signal is not a measure of the dose to the patient but indicates how much radiation was absorbed by the plate A 1 mR exposure will give – Fuji S# 200 – Kodak EI 2,000 – Agfa 200 speed lgm reference value for site EXPOSURE VALUES Exposure indicator – Plates sensitive to 0.1 mR – 100 mR – “S” number for Fuji S number inverse to exposure – S=2 (100 mR), S=200 (1 mR) Kodak uses exposure index – 2000 (1 mR), 3000 (10 mR) Exposure Values Agfa has ADC dose monitoring Stored reference dose for each exam – Based on range Compares image obtained to reference Indicates significant deviation Notes lgM, not patient dose, plate dose – Doubling dose increases lgM by 0.3 (log) Exposure Values Agfa – lgM, log gradient mean Double dose is 0.3 since it is log Have stored reference dose for exams – Set for hospital, each image compared to it – Speed class, 200 or 400 Tells relative amount of light to be read from plate Allows electronics to be optimized to this range for better image data set Agfa Agfa uses a speed system Here is a hand taken at 50, 200 and 400 speeds The mAs was changed for each one Lgm is the same for all Using Exposure Numbers Fuji, if appropriate # is 200 then – At 400, too light, double mAs for 200 – At 100, too dark, half mAs for 200 Agfa, if appropriate # is Lgm 2.2 – At 1.9, too light, double mAs for 2.2 – At 2.5, to dark, half mAs for 2.2 Kodak, if appropriate # is 1800 – At 1500, too light, double mAs for 1800 – At 2100, to dark, half mAs for 1800 S# 47 S# 86 S# 16 S# 8,357 S# 12,361 lat CXR Exposure Numbers The exposure numbers can only be used if all other parameters are correct – Centering to plate – Collimation Position over AEC, look at mAs readout to determine if poor positioning caused light or dark image Same technique, different centering and collimation S# 592 S# 664 Exposure Values Each system has range of values for appropriate exposure for part The range used by vendor is very broad Each facility should develop its own exposure range taking into account – Radiologist preference – ALARA Comparison of DR & CR IMAGE CAPTURE CR – PSP – photostimulable phosphor plate – REPLACES FILM IN THE CASSETTE DR – NO CASSETTE – PHOTONS – CAPTURED DIRECTLY – ONTO A TRANSISTOR – SENT DIRECTLY TO A MONITOR DR TFT, thin film transistor Used under silicon or selenium Collects charge then sends out as signal to computer Releases e- line by line TFT CR – PSP plate Stimulated by a RED LIGHT Energy is RELEASED in a form of BLUE light LIGHT captured by PMT – changed to a digiial signal Reference detector f-theta lens Cylindrical mirror Beam splitter Light channeling guide Laser Output Signal Source Beam deflector ADC Laser beam: Scan direction Plate translation: Sub-scan direction PMT Amplifier To image processor How CR works Released light is captured by a PMT (photo multiplier tube) This light is sent as a digital signal to the computer The intensity (brightness) of the light – correlates to the density on the image 1. X-ray Exposure Patient 5. Computed Radiograph une xposed 2. PSP 4. Image Image Image Reader Scaling Recorder detector X-ray system 3. exposed re-usable phosphor plate Densities of the IMAGE The light is proportional to amount of light received digital values are then equivalent (not exactly the same) to a value of optical density (OD) from a film, at that location of the image ADVANTAGE OF CR/DR CHANGES MADE TO IMAGE AFTER THE EXPOSURE CAN ELIMINATE THE NEED TO REPEAT THE EXPOSURE ADVANTAGE OF CR/DR vs FS Rapid storage retrieval of images NO LOST FILMS! PAC (storage management) Teleradiology - long distance transmission of image information Economic advantage - at least in the long run? CR/DR VS FILM/SCREEN FILM these can not be modified once processed If copied – lose quality DR/CR – print from file – no loss of quality “no fault” TECHNIQUES F/S: RT must choose technical factors (mAs & kvp) to optimally visualize anatomic detail CR: the selection of processing algorithms and anatomical regions controls how the acquired latent image is presented for display HOW THE IMAGE LOOKS CAN BE ALTERED BY THE COMPUTER – EVEN WHEN “BAD” TECHNIQUES ARE SET DR Initial expense high very low dose to pt – image quality of 100s using a 400s technique Therfore ¼ the dose needed to make the image Histogram Analysis A histogram is a plot of gray scale value vs. the frequency of occurrence (# pixels) of the gray value in the image HISTOGRAM – a bar graph depicting the density distribution (in numerical values) of the imaging plate ALGORITHM – a set of mathematical values used to solve a problem or find an average Histogram Low attenuation (e.g., lungs) High attenuation (e.g., mediastinum) 12,000 Frequency 10,000 8,000 6,000 4,000 2,000 0 0 200 400 600 800 1,000 Digital number Adapted from AAPM TG10 The algorithm attempts to distinguish among the parts of the histogram which represent the range of densities from bone to soft tissue Histograms set for specific exams (body parts) should produce digital images that are consistant (regardless of kVp or mAs used Correct Algorithm (body part) must be selected prior to processing imaging plate Methods to Digitize an Image 1. Film Digitizer - Teleradiography system (PACS, DICOM) 2. Video Camera (vidicon or plumbicon) 3. Computed Radiography 4. Direct Radiography FILM DIGITIZER ANALOG TO DIGITAL IMAGE Conversion of conventional analog films to digital format for PACs and teleradiology applications with scanning laser digitizers CONTRAST & DENSITY Most digital systems are capable of 1024 shades of gray - but the human eye can see only about 30 shades of gray The Optical Density and Contrast can be adjusted after the exposure by the Radiographer. This is POST - PROCESSING High displayed contrast – narrow window width Low displayed contrast (stretched) – wide window width Basics of Digital Images Pixel values can be any bit depth (values from 0 to 1023) Image contrast can be manipulated to stretched or contracted to alter the displayed contrast. Typically use “window width” and “window level” to alter displayed contrast standard image edge sharpening REPROCESSED NO GRID HAND ALGO POSITIONING & PROPER COLLIMATION ARE CRITICAL TO GOOD IMAGING OUTCOMES Just like Phototiming, it can magnify your mistakes COLLIMATION CRITICAL AS THE COMPUTER READS THE DENSITY VALUE OF EACH PIXEL – IT IS AVERAGED INTO THE TOTAL CLOSE COLLIMATION = BETTER CONTRAST BAD COLLIMATION = MORE GRAYS AND LESS DETAIL A B Digital imaging is not the end all, cure all for imaging problems. It is still technologist dependent.