Download lec6-elec

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Transistor–transistor logic wikipedia , lookup

CMOS wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Josephson voltage standard wikipedia , lookup

Schmitt trigger wikipedia , lookup

TRIAC wikipedia , lookup

Ohm's law wikipedia , lookup

Power electronics wikipedia , lookup

Voltage regulator wikipedia , lookup

Operational amplifier wikipedia , lookup

Surge protector wikipedia , lookup

Wilson current mirror wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Current source wikipedia , lookup

Two-port network wikipedia , lookup

Power MOSFET wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Opto-isolator wikipedia , lookup

Rectiverter wikipedia , lookup

Current mirror wikipedia , lookup

Transcript
BJT (cont’d)
OUTLINE
–Transconductance
–Small-signal model
–The Early effect
–BJT operation in saturation
mode
Reading: Chapter 4.4.3-4.5
Notes on PN Junctions
Typically, pn junctions in IC devices are formed by
counter-doping. The equations provided in class (and
in the textbook) can be readily applied to such diodes
if


NA  net acceptor doping on p-side (NA-ND)p-side
ND  net donor doping on n-side (ND-NA)n-side
I D  I S (e qVD
kT
 1)
 Dn
Dp 

I S  Aqni 

L N

L
N
n
A
p
D


2
ID (A)

VD (V)
Transconductance, gm


The transconductance (gm) of a transistor is a
measure of how well it converts a voltage signal
into a current signal.
It will be shown later that gm is one of the most
important parameters in integrated circuit design.
dI C
d 
VBE 
 I S exp

gm 

dVBE dVBE 
VT 
1
VBE
g m  I S exp
VT
VT
IC
gm 
VT
Visualization of Transconductance


gm can be visualized as the slope of the IC vs. VBE
curve.
The slope (hence gm) increases with IC.
Transconductance and IC

For a given VBE swing (DV), the resulting current
swing about IC2 is larger than it is about IC1.

This is because gm is larger when VBE = VB2.
Transconductance and Emitter Area
When the BJT emitter area is increased by a factor
n, IS increases by the factor n.
 For a fixed value of VBE, IC and hence gm increase
by a factor of n.

Derivation of Small-Signal Model

The BJT small-signal model is derived by perturbing
the voltage difference between two terminals while
fixing the voltage on the third terminal, and analyzing
the resultant changes in terminal currents.


This is done for each of the three terminals as the one with
fixed voltage.
We model the current change by a controlled source or
resistor.
Small-Signal Model: VBE Change
Small-Signal Model: VCE Change


Ideally, VCE has no effect on the collector current.
Thus, it will not contribute to the small-signal model.
It can be shown that VCB ideally has no effect on the
small-signal model, either.
Small-Signal Model: Example 1

The small-signal model parameters are calculated
for the DC operating point, and are used to
determine the change in IC due to a change in VBE.
IC
1
gm 

VT 3.75
r 

gm
 375
Small-Signal Model: Example 2


In this example, a resistor is placed between the power
supply and collector, to obtain an output voltage signal.
Since the power supply voltage does not vary with time,
it is regarded as ground (reference potential) in smallsignal analysis.
The Early Effect

In reality, the collector current depends on VCE:

For a fixed value of VBE, as VCE increases, the reverse bias
on the collector-base junction increases, hence the width of
the depletion region increases. Therefore, the quasineutral base width decreases, so that collector current
increases.
Early Effect: Impact on BJT I-V

Due to the Early effect, collector current increases
with increasing VCE, for a fixed value of VBE.
Early Effect Representation
Early Effect and Large-Signal Model


The Early effect can be accounted for, by simply
multiplying the collector current by a correction factor.
The base current does not change significantly.
Early Effect and Small-Signal Model
DVCE
VA
VA
ro 


VBE I C
DI C
I S exp
VT
Summary of BJT Concepts
BJT in Saturation Mode

When the collector voltage drops below the base
voltage, the collector-base junction is forward
biased. Base current increases, so that the current
gain (IC/IB) decreases.
Large-Signal Model for Saturation Mode
BJT Output Characteristics

The operating speed of the BJT also drops in
saturation.
Example: Acceptable VCC Range

In order to prevent the BJT from entering very
deeply into saturation, the collector voltage must not
fall below the base voltage by more than 400 mV.
VCC  I C RC  (VBE  400mV )
Deep Saturation


In deep saturation, the BJT does not behave as a
voltage-controlled current source.
VCE is ~constant.