Download Chapter 9 – Network Theorems

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Josephson voltage standard wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Multimeter wikipedia , lookup

Operational amplifier wikipedia , lookup

CMOS wikipedia , lookup

Schmitt trigger wikipedia , lookup

TRIAC wikipedia , lookup

Voltage regulator wikipedia , lookup

Power electronics wikipedia , lookup

Ohm's law wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Surge protector wikipedia , lookup

Opto-isolator wikipedia , lookup

Two-port network wikipedia , lookup

Power MOSFET wikipedia , lookup

Current mirror wikipedia , lookup

Current source wikipedia , lookup

Rectiverter wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

Transcript
Chapter 9 – Network Theorems
Introductory Circuit Analysis
Robert L. Boylestad
9.1 – Introduction
 This chapter introduces important fundamental
theorems of network analysis. They are the
Superposition theorem
Thévenin’s theorem
Norton’s theorem
Maximum power transfer theorem
Substitution Theorem
Millman’s theorem
Reciprocity theorem
9.2 – Superposition Theorem
 Used to find the solution to networks with two or more
sources that are not in series or parallel.
 The current through, or voltage across, an element in a
network is equal to the algebraic sum of the currents or
voltages produced independently by each source.
 Since the effect of each source will be determined
independently, the number of networks to be analyzed will
equal the number of sources.
Superposition Theorem
The total power delivered to a resistive element must
be determined using the total current through or the
total voltage across the element and cannot be
determined by a simple sum of the power levels
established by each source.
9.3 – Thévenin’s Theorem
Any two-terminal dc network can be replaced by an
equivalent circuit consisting of a voltage source and a
series resistor.
Thévenin’s Theorem
 Thévenin’s theorem can be used to:
Analyze networks with sources that are not in series or
parallel.
Reduce the number of components required to establish
the same characteristics at the output terminals.
Investigate the effect of changing a particular component
on the behavior of a network without having to analyze the
entire network after each change.
Thévenin’s Theorem
 Procedure to determine the proper values of RTh and ETh
 Preliminary
1. Remove that portion of the network across which the Thévenin
equation circuit is to be found. In the figure below, this requires that
the load resistor RL be temporarily removed from the network.
Thévenin’s Theorem
2. Mark the terminals of the remaining two-terminal network. (The
importance of this step will become obvious as we progress
through some complex networks.)
RTh:
3. Calculate RTh by first setting all sources to zero (voltage
sources are replaced by short circuits, and current sources by
open circuits) and then finding the resultant resistance between
the two marked terminals. (If the internal resistance of the
voltage and/or current sources is included in the original
network, it must remain when the sources are set to zero.)
Thévenin’s Theorem
ETh:
4. Calculate ETh by first returning all sources to their original
position and finding the open-circuit voltage between the
marked terminals. (This step is invariably the one that will lead
to the most confusion and errors. In all cases, keep in mind
that it is the open-circuit potential between the two terminals
marked in step 2.)
Thévenin’s Theorem
 Conclusion:
5. Draw the Thévenin
equivalent circuit with the
portion of the circuit
previously removed
replaced between the
terminals of the equivalent
circuit. This step is
indicated by the placement
of the resistor RL between
the terminals of the
Thévenin equivalent circuit.
Insert Figure 9.26(b)
Thévenin’s Theorem
Experimental Procedures
 Two popular experimental procedures for
determining the parameters of the Thévenin
equivalent network:
 Direct Measurement of ETh and RTh
 For any physical network, the value of ETh can be determined
experimentally by measuring the open-circuit voltage across the
load terminals.
 The value of RTh can then be determined by completing the
network with a variable resistance RL.
Thévenin’s Theorem
 Measuring VOC and ISC
 The Thévenin voltage is again determined by measuring
the open-circuit voltage across the terminals of interest; that
is, ETh = VOC. To determine RTh, a short-circuit condition is
established across the terminals of interest and the current
through the short circuit (Isc) is measured with an ammeter.
Using Ohm’s law:
RTh = Voc / Isc
9.4 – Norton’s Theorem
 Norton’s theorem states the following:
 Any two-terminal linear bilateral dc network can be
replaced by an equivalent circuit consisting of a current
and a parallel resistor.
 The steps leading to the proper values of IN and RN.
 Preliminary steps:
1. Remove that portion of the network across which the
Norton equivalent circuit is found.
2. Mark the terminals of the remaining two-terminal
network.
Norton’s Theorem
 Finding RN:
3. Calculate RN by first setting all sources to zero (voltage
sources are replaced with short circuits, and current
sources with open circuits) and then finding the resultant
resistance between the two marked terminals. (If the
internal resistance of the voltage and/or current sources is
included in the original network, it must remain when the
sources are set to zero.) Since RN = RTh the procedure
and value obtained using the approach described for
Thévenin’s theorem will determine the proper value of RN.
Norton’s Theorem
 Finding IN :
4. Calculate IN by first returning all the sources to their
original position and then finding the short-circuit current
between the marked terminals. It is the same current
that would be measured by an ammeter placed between
the marked terminals.
 Conclusion:
5. Draw the Norton equivalent circuit with the portion of the
circuit previously removed replaced between the
terminals of the equivalent circuit.
9.5 – Maximum Power Transfer
Theorem
 The maximum power transfer theorem states
the following:
A load will receive maximum power from a network
when its total resistive value is exactly equal to the
Thévenin resistance of the network applied to the
load. That is,
RL = RTh
Maximum Power Transfer Theorem
 For loads connected directly to a dc voltage
supply, maximum power will be delivered to the
load when the load resistance is equal to the
internal resistance of the source; that is, when:
RL = Rint
9.6 – Millman’s Theorem
 Any number of parallel voltage sources can be
reduced to one.
 This permits finding the current through or voltage
across RL without having to apply a method such as
mesh analysis, nodal analysis, superposition and so on.
1. Convert all voltage sources to current sources.
2. Combine parallel current sources.
3. Convert the resulting current source to a voltage source and
the desired single-source network is obtained.
9.7 – Substitution Theorem
 The substitution theorem states:
 If the voltage across and the current through any branch
of a dc bilateral network is known, this branch can be
replaced by any combination of elements that will maintain
the same voltage across and current through the chosen
branch.
 Simply, for a branch equivalence, the terminal voltage
and current must be the same.
9.8 – Reciprocity Theorem
 The reciprocity theorem is applicable only to singlesource networks and states the following:
 The current I in any branch of a network, due to a single
voltage source E anywhere in the network, will equal the
current through the branch in which the source was
originally located if the source is placed in the branch in
which the current I was originally measured.
 The location of the voltage source and the resulting current
may be interchanged without a change in current