* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download COST 286 Wroclaw - Applied Electromagnetics Lab
Survey
Document related concepts
Spectrum analyzer wikipedia , lookup
Time-to-digital converter wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Opto-isolator wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Sound level meter wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Alternating current wikipedia , lookup
History of electric power transmission wikipedia , lookup
Transcript
Research activities in Liège Ir. V. Beauvois, Ir. S. Coets, Ir. M. Renard and Ir. Ph. Camus [email protected] ULg - EMC Lab Cost 286 Wroclaw 1 st 1 Research interest: conducted and radiated emissions measurements on large systems Ir. V. Beauvois, Ir. S. Coets and Ir. M. Renard (Sorrento 2002 and Zurich 2003) in coll. With Johan Catrysse (KHBO, Oostende, Belgium) [email protected] ULg - EMC Lab Cost 286 Wroclaw 2 Conducted Emission – Introduction In the low frequency range [150kHz - 30MHz] , conducted emission measurements are performed with: a LISN (Line Impedance Stabilized Network) which prevents the EUT from the noise coming from the mains provides a defined impedance at the point of measurement a passive voltage probe if LISN unavailable (i.e. if currents too large) ULg - EMC Lab Cost 286 Wroclaw 3 Conducted Emission - Measurement Setup ULg - EMC Lab Cost 286 Wroclaw 4 Conducted Emission - Problems encountered With the LISN, the measurement is always performed at point 1b The point of measurement is ‘‘standardized’’ (fixed) Oppositely, the voltage probe (point 2) can be placed anywhere between points 1b and 3, depending on the ‘‘accessibility’’ of the EUT Which signal voltage is measured (distributed impedance between 1b and 3 not negligible) ?? Solution: introduction of a new concept: the six-pole ULg - EMC Lab Cost 286 Wroclaw 5 Conducted Emission - Six-pole Concept In this research, only single-phased situations are considered concept of the six-pole If three-phased situations without neutral (3P + PE) eight-pole If three-phased situations with neutral (3P + N + PE) ten-pole ULg - EMC Lab Cost 286 Wroclaw 6 Cond. Emission - More accurate model EUT emission signal voltage H1 : six-pole between mains and point of measurement (1b or 2) H2 : six-pole between point of measurement and EUT ULg - EMC Lab Cost 286 Wroclaw 7 Cond. Emission - Actual and Future Works As the tests performed without LISN may not be compared with those performed with LISN, the next steps of the study are: create a ‘‘virtual’’ power mains network similar to the LISN ’s one and perform measurements with the help of this ‘‘LISN-equivalent network’’ for instance by the use of an EMI filter instead of the LISN an alternating method to the LISN could then be reached ULg - EMC Lab Cost 286 Wroclaw 8 Cond. Emission - Actual and Future Works (contd) • time domain and frequency domain measurements are done. • alternate measurement methods : - classical passive voltage probe (one or two with differential method) - alternate probes and clamps (capacitive clamp, EM clamp, current probe) improve the sensitivity of the measurements and the signal -processing to get more accurate results ULg - EMC Lab Cost 286 Wroclaw 9 Radiated emission - Introduction Theoretical test configuration: ULg - EMC Lab Cost 286 Wroclaw 10 Radiated emission - Problems encountered Noise coming from the environment. Multiple reflexions « against » the environment which leads to an over-estimation or an under-estimation of the emission of the EUT. The measurement cannot necessarily be performed at a 10 meters distance from the EUT. How many measurements are to be done? And where? ULg - EMC Lab Cost 286 Wroclaw 11 Radiated emission - Solutions to consider Retrieve the right signal from noise by using a differential method. As the measurements cannot be performed at a 10 meters (or 3 meters) distance, perform near-field measurements in addition with a near-field far-field transformation. Take into account the reflecting characteristics of the global environment ULg - EMC Lab Cost 286 Wroclaw 12 nd 2 Research interest: Characterization and modelling of embedded systems emissions Ir. V. Beauvois, Ir. Ph. Camus [email protected] ULg - EMC Lab Cost 286 Wroclaw 13 Architecture of embedded systems Main clock Data Transmission Lines µcontroller I/O Controller Level shifters Analog and Power Section Sensors and Actuators Memory Power Supply ULg - EMC Lab Cost 286 Wroclaw 14 Fast switching occurs on the bus and transmission lines which leads to current pulses. Current pulses produce electromagnetic emissions radiated through the P.C.B. traces, integrated circuits pads and connected cables. For a given architecture and software, the current waveforms on the board connections can be evaluated - they are related to electromagnetic emission. By mean of Fourier transform the spectrum can be computed and compared with EMC limits. ULg - EMC Lab Cost 286 Wroclaw 15 Typical waveforms – Data bus Boucle while(1); durée =100 µs 7 6 5 4 3 2 1 0 0 50 100 150 200 t (µs) 250 300 350 400 Data bus, address bus and control signal are combined (summation) in time domain. 5000 4000 3000 2000 1000 0 0 20 40 60 80 f (kHz) 100 120 140 160 One simple loop on 80C320 Dallas ULg - EMC Lab Cost 286 Wroclaw As signals are synchronous (one main clock) phase is the same for each signal at a given frequency -> spectrum can be easily computed. 16 Typical waveforms – Power supply • White filtered noise for analog parts • Simple pulse noise for switched circuits 7805 linear regulator (white noise with cut off frequency near 1 MHz) and MAX232 level shifter (245 kHz and harmonics) ULg - EMC Lab Cost 286 Wroclaw 17 Typical waveforms – Analog and Power section • Classification into families of circuits with same noise signatures • White filtered noise and switching noise. ULg - EMC Lab Cost 286 Wroclaw 18 First results and actual works Conducted and radiated emission of a 80C320 board were measured for different codes and compared with computed spectrum : • computed spectrum components occur • at the same frequency as in the measurement on a real circuit ; • variation of amplitude follows a similar envelope. ULg - EMC Lab Cost 286 Wroclaw 19 Actual and Future Works • Characterization of a great number of boards : same CPU with different clocks and different peripherals, … • Better modelling of switching process and relationship with conducted and radiated noise. • VHDL modelling of CPU to gain a better comprehension of processor noise sources, synthesis into an FPGA and measurements in anechoic chamber. • Development of software tools to predict noise behaviour of embedded systems. ULg - EMC Lab Cost 286 Wroclaw 20