Download Slide 1

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts
Transcript
Channel Length Modulation
•
•
•
The inversion layer charge QI
represents the total mobile electron
charge on the surface and its
expression at the source end of the
channel is:
QI at x=0=-Cox(VGS-VT0) and the
inversion layer charge at the drain end
of the channel is expressed as: QI at
x=L=-Cox(VGS-VT0-VDS)
At the edge of saturation when the
drain-to-source voltage reaches
saturation (VDS=VDSAT=VGS-VT0) the
inversion layer charge at the drain end
becomes zero.
•
•
•
•
•
We can approximate the inversion
layer charge at the drain end by QI at
x=L=0 (even though this is not quite
true)
When VDS=VDSAT, the channel is
pinched off at the drain end.
Further increase of the drain-tosource voltage (VDS>VDSAT) results in
even a larger pinched-off portion of
the channel.
The effective channel length is
reduced to: L’=L-DL where DL is the
length of the channel where QI=0.
The pinch-off point moves from the
drain end of the channel towards the
source end with increasing VDS.
Channel Length Modulation
• For L’<x<L the channel voltage is
Vc at x=L’=VDSAT.
• The electrons traveling from
source to drain traverse the
inverted channel segment of
length L’ and then they are
injected into the depletion region
of length DL that separates the
pinch-off point from the drain
edge.
• The gradual channel
approximation is valid in this
region and is given by:
IDSAT=(mnCox)/2(W/L’)[VGS-VT0]2
• The effective channel length for
the MOSFET operating in
saturation is now L’ and the above
equation accounts for the actual
shortening of the channel.
• Shortening of the channel is also
known as channel length
modulation.
• If L’ is replaced by L in the
equation we can show that the
computed saturation current using
L’ is greater than the new IDSAT
computed using L.
Channel Length Modulation
• We must modify the equation for
saturation current so that it
reflects the dependency on VDS.
Note that the saturation current
will increase with increasing VDS
since L’ decreases with increasing
VDS.
I DSAT


 1 m C W
 n ox VGS  VT 0 2

 1  DL  2 L
L 

• The first term of the equation
accounts for the channel length
modulation effect.
DL 
VDS  VDSAT
• Let 1-DL1-lVDS, with l being
an empirical model parameter
called the channel length
modulation coefficient.
• Assume that lVDS<<1 then the
saturation current becomes:
I DSAT 
mnCox W
2
L
VGS  VT 0 2 1  lVDS 
• The above equation can be used
with sufficient confidence for
most first order hand calculations
MOS Capcitances
• So far the analysis has been on the
steady state behavior of the MOS
transistor.
• In order to examine the transient
(AC) response of MOSFETs the
digital circuits consisting of
MOSFETs we have to determine
the nature and amount of parasitic
capacitances associated with the
MOS transistor.
• On chip capacitances found on
MOS circuits are in general
complicated functions of the
layout geometries and the
manufacturing processes.
• Most of these capacitances are not
lumped but distributed and their
exact calculations would usually
require complex three
dimensional nonlinear chargevoltage models.
• A lumped representation of the
capacitance can be used to
analyze the dynamic transient
behavior of the device.
• The capacitances can be classified
as oxide related or junction
capacitances and we will start the
analysis with the oxide related
capacitances.
The MOS Transistor
MOS Capacitances
Cgb
D
Cdb
Cgd
G
B
Csb
Cgs
S
• Masks result in some
regions having overlaps,
for example the gate
electrode overlaps both the
source and drain regions at
the edges.
• Two overlap capacitances
arise as a result.
• These are Cgs and Cgd
respectively.
• If both the source and drain
regions have the same width (W),
the overlap capacitance becomes:
Cgs=CoxWLD and Cgd=CoxWLD.
• These overlap capacitances are
voltage dependent.
• Cgs, Cgd and Cgb are voltage
dependent and distributed
• They result from the interaction
between the gate voltage and the
channel charge.
MOS Oxide Capacitances
• The gate-to-source capacitance is
actually the gate-to-channel
capacitance seen between the gate
and the source terminals.
• The gate-to-drain capacitance is
actually the gate-to-channel
capacitance seen between the gate
and the drain terminals.
• In Cut-off mode the surface is not
inverted and there is no
conducting channel linking the
surface to the source and to the
drain.
• The gate-to-source and gate-todrain capacitances are both equal
to zero (Cgs=Cgd=0).
• The gate-to-substrate capacitance
can be approximated by:
Cgb=CoxWL
• In linear mode the inverted
channel extends across the
MOSFET between the source and
drain. This conducting inversion
layer on the surface effectively
shields the substrate from the gate
electric field making it Cgb=0.
MOSFET Oxide Capacitance
• In linear mode the distributed
gate-to-channel capacitance
maybe viewed as being shared
equally between the source and
the drain leading to:
Cgs=Cgd=0.5CoxWL
• If the MOSFET is operating in
saturation mode the inversion
layer on the surface does not
extend to the drain, but is pinched
off.
• The gate-to-drain capacitance in
therefore zero (Cgd=0).
• The source is however still linked
to the conducting channel. It
shields the gate from the channel
leading to Cgb of zero.
• The distributed gate-to-channel
capacitance as seen between the
gate and the source is
approximated by: Cgs2/3CoxWL.