Download Logic Families - Dr Ali El-Mousa

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Immunity-aware programming wikipedia , lookup

Stray voltage wikipedia , lookup

Power inverter wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Transistor wikipedia , lookup

Current source wikipedia , lookup

Voltage optimisation wikipedia , lookup

Alternating current wikipedia , lookup

Mains electricity wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Rectifier wikipedia , lookup

Flip-flop (electronics) wikipedia , lookup

Two-port network wikipedia , lookup

Power electronics wikipedia , lookup

Buck converter wikipedia , lookup

Schmitt trigger wikipedia , lookup

Curry–Howard correspondence wikipedia , lookup

Control system wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Current mirror wikipedia , lookup

Digital electronics wikipedia , lookup

Opto-isolator wikipedia , lookup

CMOS wikipedia , lookup

Transcript
Logic Families
Introduction
Logic Family Definition
A circuit configuration or approach used to
produce a type of digital integrated circuit.
 Consequence: different logic functions,
when fabricated in the form of an IC with
the same approach, or in other words
belonging to the same logic family, will have
identical electrical characteristics.
 the set of digital ICs belonging to the same
logic family are electrically compatible with
each other

2
Common Characteristics of the
Same Logic Family
Supply voltage range, speed of response,
power dissipation, input and output logic
levels, current sourcing and sinking
capability, fan-out, noise margin, etc.
 Consequence: choosing digital ICs from
the same logic family guarantees that
these ICs are compatible with respect to
each other and that the system as a
whole performs the intended logic
function.

3
Types of Logic Family 1
The entire range of digital ICs is fabricated
using either bipolar devices or MOS devices
or a combination of the two.
 Bipolar families:

◦
◦
◦
◦
◦
Diode logic (DL). (obsolete)
Resistor transistor logic (RTL). (obsolete)
Diode transistor logic (DTL). (obsolete)
Transistor Transistor logic (TTL).
Emitter Coupled Logic (ECL), also known as
Current Mode Logic(CML).
◦ Integrated Injection logic (I2L). (obsolete)
4
Types of Logic Family 2
 MOS
families:
◦ PMOS family (using P-channel MOSFETs)
◦ The NMOS family (using N-channel
MOSFETs)
◦ The CMOS family (using both N- and Pchannel devices).
◦ The Bi-MOS logic family uses both bipolar
and MOS devices.
5
DL Example
6
RTL Example
7
DTL Example
8
TTL Subfamilies
9
CMOS Sub families
4000A
 4000B, 4000UB,
 54/74C, 54/74HC, 54/74HCT, 54/74AC
and 54/74ACT(TTL pin compatible)

10
Characteristic Parameters 1
HIGH-level input current, IIH (current flowing into
(taken as positive) or out of (taken as negative) an input
when a HIGH-level input voltage equal to the minimum
HIGH-level output voltage specified for the family is applied.
 LOW-level input current, IIL. is the maximum current
flowing into (taken as positive) or out of (taken as negative)
the input of a logic function when the voltage applied at the
input equals the maximum LOW-level output voltage
specified for the family.
 unit load (UL) HIGH-level and LOW-level input current or
loading typically found in data sheets (For devices of the TTL
family, 1 UL (HIGH)=40 A and 1 UL (LOW)=1.6 mA.

11
Characteristic Parameters 2

HIGH-level output current, IOH. This is the
maximum current flowing out of an output
when the input conditions are such that

the output is in the logic HIGH state.
Typically negative number.
LOW-level output current, IOL. This is the
maximum current flowing into the output
pin of a logic function when the input
conditions are such that the output is in
the logic LOW state.
12
Characteristic Parameters 3

HIGH-level off-state (high-impedance state) output
current, IOZH. This
is the current flowing into
an output of a tristate logic function with the
ENABLE input chosen so as to establish a
high-impedance state and a logic HIGH
voltage level applied at the output. The input
conditions are chosen so as to produce logic
LOW if the device is enabled.
13
Input and output current specifications
14
Characteristic Parameters 4


This is the
maximum voltage level applied at the input
that is recognized as a legal LOW level for
the specified family.
HIGH-level output voltage, VOH. This is the
minimum voltage on the output pin of a logic
function when the input conditions establish
logic HIGH at the output for the specified
family.
LOW-level input voltage, VIL.
15
Characteristic Parameters 5

This is the
minimum voltage on the output pin of a
logic function when the input conditions
establish logic HIGH at the output for the
specified family.
HIGH-level output voltage, VOH.
16
Characteristic Parameters 6



Supply current, ICC. The
supply current when
the output is HIGH, LOW and in the highimpedance state is respectively designated as
ICCH, ICCL and ICCZ.
Rise time, tr. This is the time that elapses
between 10 and 90 % of the final signal level
when the signal is making a transition from
logic LOW to logic HIGH.
Fall time, tf . This is the time that elapses
between 90 and 10 % of the signal level
when it is making HIGH to LOW transition.
17
Characteristic Parameters 7


Propagation delay tp. is
the time delay between
the occurrence of change in the logical level at
the input and before it is reflected at the
output. It is the time delay between the
specified voltage points on the input and
output waveforms.
Propagation delays are separately defined for
LOW-to-HIGH and HIGH-to-LOW
transitions at the output. In addition, we also
define enable and disable time delays that
occur during transition between the highimpedance state and defined logic LOW or
HIGH states.
18
Characteristic Parameters 8


This is the maximum
frequency at which the clock input of a flip-flop
can be driven through its required sequence
while maintaining stable transitions of logic level
at the output in accordance with the input
conditions and the product specification.
Power dissipation. The power dissipation
parameter for a logic family is specified in terms
of power consumption per gate and is the
product of supply voltage VCC and supply
current ICC.
Maximum clock frequency, fmax.
19
Characteristic Parameters 9



Speed–power product. The speed of a logic circuit
can be increased, that is, the propagation delay can be
reduced, at the expense of power dissipation.
Fan-out. is the number of inputs of a logic function
that can be driven from a single output without
causing any false output.
Noise margin. This is a quantitative measure of noise
immunity offered by the logic family. When the output
of a logic device feeds the input of another device of
the same family, a legal HIGH logic state at the output
of the feeding device should be treated as a legal
HIGH logic state by the input of the device being fed.
Similarly, a legal LOW logic state of the feeding device
should be treated as a legal LOW logic state by the
device being fed.
20
Noise MARGIN
21
22
23