Download ballast - Arlight

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Electrical substation wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Rectifier wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Electronic paper wikipedia , lookup

Control system wikipedia , lookup

Stray voltage wikipedia , lookup

War of the currents wikipedia , lookup

Electrification wikipedia , lookup

Buck converter wikipedia , lookup

Distribution management system wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Power electronics wikipedia , lookup

Rectiverter wikipedia , lookup

Alternating current wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

History of electric power transmission wikipedia , lookup

Mains electricity wikipedia , lookup

Opto-isolator wikipedia , lookup

Voltage optimisation wikipedia , lookup

LED lamp wikipedia , lookup

Street light wikipedia , lookup

Electrical ballast wikipedia , lookup

Transcript
Training manual
Training manual
Chapter 3
Ballasts and Lighting Controls
Lighting concepts – Ballasts and Lighting Controls
Training manual
Ballasts
All discharge lamps (fluorescent and HID) require an auxiliary
piece of equipment called a ballast.
Ballasts have three main functions:
•provide correct starting voltage, because
lamps require a higher voltage to start than
to operate
•match the line voltage to the operating
voltage of the lamp
•limit the lamp current to prevent immediate
destruction, because once the arc is struck
the lamp impedance decreases
Lighting concepts – Ballasts and Lighting Controls
Training manual
Ballasts
•Ballasts are an integral component of the lighting system
•They have a direct impact on light output.
•The ballast factor is the ratio of a lamp's light output using a standard reference ballast,
compared to the lamp's rated light output on a laboratory standard ballast.
•General purpose ballasts have a ballast factor that is less than one; special ballasts
may have a ballast factor greater than one.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
The two general types of fluorescent ballasts are :
• magnetic ballasts
• electronic ballasts
Magnetic Ballasts
Magnetic ballasts (also referred to as electromagnetic ballasts)
fall into one of the following categories:
•standard core-coil ( no longer in use)
•high-efficiency core-coil
•cathode cut-out or hybrid
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
"Cathode cut-out" (or "hybrid") ballasts are high-efficiency core-coil ballasts that
incorporate electronic components that cut off power to the lamp cathodes (filaments)
after the lamps are lit, resulting in an additional 2-watt savings per standard lamp.
Also, many partial-output T12 hybrid ballasts provide up to 10% less light output while
consuming up to 17% less energy than energy-efficient magnetic ballasts.
Full-output T8 hybrid ballasts are nearly as efficient as rapid-start two-lamp T8
electronic ballasts.
Electromagnetic fluorescent ballasts
require a starter to ingnite and function
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Electronic Ballasts
In nearly every full-size fluorescent lighting application, electronic ballasts can be used
in place of conventional magnetic ballasts.
Electronic ballasts improve fluorescent system efficacy by converting the standard 60
Hz input frequency to a higher frequency, usually 25,000 to 40,000 Hz.
Lamps operating at these higher frequencies produce about the same amount of light,
while consuming 12 to 25 percent less power.
Other advantages of electronic ballasts :
•less audible noise
•less weight
•virtually no lamp flicker
•dimming capabilities (with specific ballast models).
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Electronic Ballasts
Dimmable electronic ballasts permit the light output of the lamps to be dimmed based
on input from manual dimmer controls or from devices that sense daylight or
occupancy.
Ballast factor (BF) is the ratio of the
light output of a lamp or lamps operated
by a specific ballast to the light output of
the same lamp(s) operated by a
reference ballast.
BF can be used to calculate the actual
light output of a specific lamp-ballast
combination when designing a
fluorescent lighting system.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Electronic Ballasts
Also, temperature is an important key
element in a ballast performance.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Dimmable Electronic Ballasts
Dimming electronic ballasts for fluorescent lamps can save energy and increase the range
Of illuminances provided by a lighting system.
A dimming system saves energy relative to a non-dimming system, assuming lamps are
dimmed and both systems are operating for similar periods of time.
Control devices for dimming electronic ballasts include automatic and manual dimmers,
photo-sensors to dim lamps when daylight is available, and energy management systems
that dim lamps during peak demand hours or at night.
Dimming electronic ballasts contains one of two
types of controls circuits:
•Low voltage
•High voltage
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Dimmable Electronic Ballasts
Low voltage dimming electronic ballasts have two wires of a low-voltage control circuit
rated at 0 to 10 Volts direct current (Vdc).The ballast supplies voltage to a control device,
such a photosensor.
For full light output on this circuit, the control device returns the maximum control signal to
the dimming ballast.For less than full light output, the control device reduces the voltage
across the control wires, causing the ballast to dim the lamps.As the control voltage
approches 0 Vdc, the ballast dims the lamps to the lowest light output possible for that
system.
High voltage dimming electronic ballasts do not have additional control wires.
Instead, high-voltage control devices such manual dimmers are typically installed
between the electrical supply and the “hot”lead of the ballast and can be used to replace
light switches.
Ballasts life ranges from 10 to 20 years and depends of temperature and operating
voltage.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Fluorescent Ballasts
Dimmable Electronic Ballasts
Type of dimmable ballasts:
•1-10V analogue control
•DSI
•DALI
Lighting concepts – Ballasts and Lighting Controls
Training manual
Lighting Controls
•Timers
•Sensors
•Timed Switches
•Photocells
•Lighting Control Panels
•Building Automation Systems
Timers can be effectively utilized for basic on/off operation of lighting fixtures.
By utilizing low voltage relays, large numbers of fixtures can be controlled by
a single timer, thereby making it very cost effective.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Lighting Controls
Most sensors in commercial applications utilize either passive infrared (PIR)
or ultrasonic technology. There are units on the market that integrate both
technologies into a hybrid sensor design.
Presence sensor
Daylight sensor
Lighting concepts – Ballasts and Lighting Controls
Training manual
Lighting Controls
Timed Switches are switches that incorporate a timed function, to ensure that
the fixtures are turned off after a preset interval of time, typically one to two
hours.
A photocell is an sensor that is supplied by a
power feed and switches a load e.g:500W
light when it becomes dark, letting electricity
flow from mains side to the load side of the
sensors relay therefore activating the light.
Time switch
Lighting concepts – Ballasts and Lighting Controls
Training manual
Lighting Controls
A Building Management System (BMS) is a computer-based control
system installed in buildings that controls and monitors the building’s
mechanical and electrical equipment such as ventilation, lighting, power
systems, fire systems, and security systems
Building Management Systems are most commonly implemented in large
projects with extensive mechanical, electrical, and plumbing systems.
Systems linked to a BMS typically represent 40% of a building's energy
usage; if lighting is included, this number approaches 70%.
Lighting concepts – Ballasts and Lighting Controls
Training manual
HID Ballasts
Like fluorescent lamps, HID lamps require a ballast to start and operate.
•The purposes of the ballast are similar: to provide starting voltage, to limit the current,
and to match the line voltage to the arc voltage.
•With HID ballasts, a major performance consideration is lamp wattage regulation
when the line voltage varies. With HPS lamps, the ballast must compensate for
changes in the lamp voltage as well as for changes in the line voltages.
Installing the wrong HID ballast can cause a variety of problems:
•waste energy and increase operating cost
•severely shorten lamp life
•significantly add to system maintenance costs
•produce lower-than-desired light levels
•increase wiring and circuit breaker installation costs
•result in lamp cycling when voltage dips occur
Lighting concepts – Ballasts and Lighting Controls
Training manual
HID Ballasts
•Capacitive switching is available in new HID luminaires with special HID ballasts.
The most common application for HID capacitive switching is in occupancy-sensed bilevel lighting control.
•Upon sensing motion, the occupancy sensor will send a signal to the bi-level HID
system that will rapidly bring the light levels from a standby reduced level to
approximately 80% of full output, followed by the normal warm-up time between 80%
and 100% of full light output.
• Depending on the lamp type and wattage, the standby lumens are roughly 15-40% of
full output and the input watts are 30-60% of full wattage.
•Therefore, during periods that the space is unoccupied and the system is dimmed,
savings of 40-70% are achieved.
Lighting concepts – Ballasts and Lighting Controls
Training manual
Lighting concepts – Ballasts and Lighting Controls