Download 380VDC 6-Lamp Ballast Retrofit Installation and Userʼs Manual NB380-T832-06-ISBL

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Fault tolerance wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Electrical engineering wikipedia , lookup

Three-phase electric power wikipedia , lookup

Buck converter wikipedia , lookup

Public address system wikipedia , lookup

Islanding wikipedia , lookup

Electrical substation wikipedia , lookup

Electrician wikipedia , lookup

Electronic engineering wikipedia , lookup

Wireless power transfer wikipedia , lookup

Audio power wikipedia , lookup

Power over Ethernet wikipedia , lookup

Stray voltage wikipedia , lookup

Power electronics wikipedia , lookup

Single-wire earth return wikipedia , lookup

Rectiverter wikipedia , lookup

Electrification wikipedia , lookup

Earthing system wikipedia , lookup

Voltage optimisation wikipedia , lookup

Electric power system wikipedia , lookup

Distribution management system wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Telecommunications engineering wikipedia , lookup

Ground (electricity) wikipedia , lookup

Switched-mode power supply wikipedia , lookup

History of electric power transmission wikipedia , lookup

AC adapter wikipedia , lookup

Power engineering wikipedia , lookup

Alternating current wikipedia , lookup

National Electrical Code wikipedia , lookup

Electrical wiring wikipedia , lookup

Electrical wiring in the United Kingdom wikipedia , lookup

Mains electricity wikipedia , lookup

Electrical ballast wikipedia , lookup

Transcript
380VDC 6-Lamp Ballast Retrofit
Installation and Userʼs Manual
380VDC SIX LAMP BALLAST MODEL:
NB380-T832-06-ISBL
Rev. 052014
Please contact Customer Support at 1-877-24VOLTS for further information.
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the
United States and in other countries throughout the world.
380VDC, 6-Lamp Ballast Retrofit Kit
Installation and Userʼs Manual
TABLE OF CONTENTS
ABOUT NEXTEK POWER SYSTEMS
3
INTRODUCTION / OVERVIEW
4
1.0
SAFETY
5
2.0
STANDARDS & REQUIREMENTS
6
3.0
REGULATORY INFORMATION
7
4.0
TRAINING
7
5.0
FEATURES AND SPECIFICATIONS
8
6.0
GENERAL REQUIREMENTS
9
7.0
INSTALLATION PROCEDURE
11
8.0
NOTES
17
For more information:
2
Nextek Power Systems
461 Burroughs Street
Detroit, Michigan 48202
Tel: 313-887-1321
Toll free: 1 (877) 24-VOLTS
Fax: 313-887-9433
www.nextekpower.com
[email protected]
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
Installation and Userʼs Manual
ABOUT NEXTEK POWER SYSTEMS
Nextek Power Systems AC/DC integration technology represents a breakthrough in onsite electrical management, combining the availability of AC power with the quality and
efficiency of a DC supply.
NEXTEK PRODUCT BENEFITS
•
Easy conversion of AC lighting fixtures to DC-powered units
•
Easy conversion of AC grid power into DC power for commercial building
applications
•
Highly efficient management of peak loads
•
Future-proof lighting and other systems to be developed
•
Nextek Power Systems Direct Coupling® Technology, directly connects clean
power generated at a building to its electronic loads inside cutting down on overall power consumption, boosts electricity generated and stored on-site, and
delivers a robust renewable energy ready network.
DISCLAIMER
Nextek Power Systems has made every reasonable effort to ensure the accuracy of the
information in this catalog. Nextek Power Systems does not guarantee that the
information is error free, nor do we make any other representation, warranty or
guarantee that the information is accurate, correct, reliable or current. Nextek Power
Systems, Inc. reserves the right to make any adjustments to the information contained
herein at any time without notice. The specifications in this catalog are for reference
purposes only and are subject to change without notice. Consult Nextek Power Systems
for the latest design specifications. All trademarks are either the exclusive property of
Nextek Power Systems, Inc. or other companies. Copyright © 2013-2014 by Nextek
Power Systems, Inc. in the United States and other countries throughout the world.
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
3
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
Installation and Userʼs Manual
INTRODUCTION
Nextek Ballasts
• Nextekʼs 380VDC Ballast Retrofit Kit converts existing luminaires from AC power to high
efficiency, bus voltage Direct Current (DC) power by simply replacing the ballasts.
• Convert luminaires without replacing bulbs or system wiring. Nextek ballasts are sized to use
pre-existing mounting holes and hardware too.
• The simple procedure takes only minutes to complete.
• A Maximum Power Point Tracking Controller is recommended for greatest system efficiency
and control.
HIGH VOLTAGE DIRECT CURRENT INPUT FROM PV PANEL,
HVDC GRID, OR OTHER DC POWER GENERATOR
BATTERY STORAGE
MPPT
AC to DC
CONVERTER
380 VDC BUS
AC GRID POWER INPUT
NEXTEK 380VDC,
6 LAMP BALLASTS
FLUORESCENT LUMINAIRES
Nextek ballasts in a Direct Current microgrid power system.
4
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
1.0
Installation and Userʼs Manual
SAFETY
1.1 SAVE THESE INSTRUCTIONS– This manual contains important safety and
operating instructions for the Nextek Ballast Retrofit Kit.
The following symbols are used throughout this manual to indicate potentially
dangerous conditions or mark important safety instructions:
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially dangerous condition. Use extreme caution when
performing this task.
CAUTION:
Indicates a critical procedure for safe and proper operation of the
controller.
NOTE:
Indicates a procedure or function that is important for the safe and
proper operation of the controller.
1.2 Before using the Ballast Retrofit Kit, read all instructions and cautionary
markings.
1.3 Electrical hazards are probably the most common hazards throughout the
industry. Virtually all workplaces have electrical installations and use electricity.
1.4 It is very important that all industry employees be familiar with electrical hazards
and know how to protect themselves when working on, near, or with electricity.
In most cases, industry electrical and electronic equipment is designed for both
maximum safety and efficiency. However, potentially hazardous conditions such
as inadvertent contact with hazardous voltages may exist while performing
servicing and maintenance, handling materials, or cleaning.
1.5 The improper use of electrical extension cords and portable electrical
equipment can result in hazardous exposure.
1.6
WARNING - RISK OF ELECTRICAL SHOCK OR FIRE
1.6.1 This Ballast Retrofit Kit requires knowledge of fluorescent lighting
luminaires electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
1.6.2 This kit is intended only for use with luminaires located in dry locations
(indoors).
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
5
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
1.0
Installation and Userʼs Manual
SAFETY
1.6
WARNING - RISK OF ELECTRICAL SHOCK OR FIRE
1.6.3 Install this kit only in non-IC luminaires that have similar features and
dimensions as the photographs and/or drawings shown here. (Not
intended for Insulation Contact.)
1.6.4 The ballast supplied with this kit is intended for use with instant-start
lampholders. Lampholders marked with a circle “I” meet these
requirements. Tombstone pins in the lampholder should be shorted.
1.6.5 WARNING: To prevent wiring damage or abrasion, do not expose wiring
to edges of sheet metal or other sharp objects.
1.6.6 Only those open holes indicated in the photographs and/or drawings may
be made or altered as a result of kit installation. Do not leave any other
open holes in an enclosure of wiring or electrical components.
1.6.7 A listed Class 1 380VDC output supply, such as a 380VDC bus line, may
be used as a power source for the Nextek 380VDC ballast.
1.6.8 Before wiring 380VDC supply to ballasts, remove any old AC wiring,
including any ground wires, between the line voltage ballast and the
nearest junction box.
1.7
DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
1.7.1 Do not disassemble or attempt to repair the ballasts. There are no user
serviceable parts inside Nextek ballasts.
1.7.2 Install external fuses/breakers as required.
1.7.3 Disconnect power to the luminaire before installing the ballasts, removing
old ballasts or wiring, or otherwise working with the unit.
1.8 INSTALLATION SAFETY PRECAUTIONS
1.8.1 Mount the Ballast Retrofit Kit indoors only. Prevent exposure to the
elements.
1.8.2 Power connections must remain tight to avoid excessive heating from a
loose connection.
1.8.3 Use properly sized conductors and circuit interrupters.
1.8.4 The Nextek Ballast Retrofit Kit is to be connected to DC circuits only.
6
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
2.0
Installation and Userʼs Manual
STANDARDS AND REQUIREMENTS
2.0
3.0
STANDARDS AND REQUIREMENTS
2.1 All DC cable types must meet all local and national codes
2.2 Shut off all DC circuit breakers or fuses before installing any unit into the field.
3.1
REGULATORY INFORMATION
NOTE: This section contains important information for safety and
regulatory requirements.
3.2 The Ballast Retrofit Kit should be installed by a qualified technician according to
the electrical rules of the country in which the product will be installed.
3.3 Nextek ballasts comply with the following EMI standards:
3.3.1 Immunity: EN61000-6-2:1999
3.3.2 Emissions: EN55022:1994 with A1 and A3 Class B1
3.4 A means shall be provided to ensure all the poles are disconnected from the
power supply. This disconnection shall be incorporated in the fixed wiring.
3.5 FCC Requirements:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Nextek Power Systems, Inc. for compliance
could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 18 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communication. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment on and off, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
4.0
INSTALLATION QUALIFICATIONS
4.1 Installation work and electrical wiring of permanently-connected power units
must be performed only by qualified service personnel in accordance with all
applicable codes and standards, including fire-rated construction.
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
7
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
5.0
Installation and Userʼs Manual
BALLAST FEATURES AND SPECIFICATIONS
5.1 Features
• Tri-stage dimming that allows for 0%,
33% (2 lamp), 66% (4 lamp), and 100%
(6 lamp) of the lamps to be lit.
• Simple Mechanical / Smart Switch
configurable with NO/NC
• > 97% efficient
• Class 1 24VDC/250mA out for
powering ballast accessories, e.g.
Smart Switches and emergency/
backup ballasts.
• Auxiliary Output supply of 24VDC /
250mA to power smart switches
• Simple Mechanical / Smart Switch
configurable
• Works at 10-65ºC ambient, perfect for
Highbay applications
• Low cost 6-lamp class ballast
• Type 1, Class P, Sound rated A
• UL 935, UL E242233, UL 1012 / CUL
listed; CSA 22.2 No. 74, CSA 22.2 No.
107.1
5.2 Technical Specifications
Operating Voltage:
380 VDC (nominal)
265-400 VDC
Operating Current:
0.60 Amp @ 380 VDC
Operating
Temperature:
10ºC-65ºC
Maximum Ballast
Factor:
1.14
Peak Efficiency:
> 97%
Crest Factor:
< 1.5
Dimming:
Tri-level
Dimensions:
W=1.7" H=1.2" L=14.2"
(44mm x 31mm x 362mm)
Weight:
1.5 lbs.
Construction:
Steel
Operated With:
F32T8, F32T8ES,
FB032, FB32*
All specifications are subject to change without notice.
*For wattages other than 32, please contact Nextek Power Systems, Inc. at
1-877-24VOLTS
5.3 Enclosure Diagram
5.4 Kit contents:
1. Ballast
2. These instructions
3. Wire nuts: 18 for six-lamp ballast conversion
4. Cable ties (6)
5. Labels to be affixed to exterior of luminaire:
8
Luminaire Conversion Retrofit
This luminaire contains a 380V DC input ballast
Nextek Power Systems
461 Burroughs St, Detroit, MI 48202
www.nextekpower.com
Use only with 380VDC Class 1 Power Unit
Do not connect to line voltage
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
6.0
Installation and Userʼs Manual
GENERAL REQUIREMENTS
6.1 Every work environment should provide a safe place for every employee, which
includes protecting the employee from electrical hazards such as fault currents
to ground.
6.2 When an electrical ground fault occurs, the current flows through the path
having minimum impedance to ground. It is imperative that an employee does
not inadvertently become the conductor of the current.
6.3 Two approved methods of protecting the worker from a ground fault, in addition
to other requirements for equipment-grounding conductors, are:
6.3.1 Use of ground fault circuit interrupters (GFCI)
6.3.2 An assured equipment grounding conductor program
6.4 Installers should be advised:
6.4.1 These installation instructions are for use by qualified personnel only.
NOTE: Installers must reference the National Electric Code (NEC)
sections
250 or 690, when required, to ensure proper system wiring
6.4.2 The equipment contains DC voltages.
6.4.3
and grounding compliance. In addition, all state and federal
Occupational Safety and Health Administration (OSHA) guidelines
and regulations must be followed.
NOTE: Installers must reference the specific site scope and project
drawings
for additional information and considerations, including the
6.4.4
system layout and any related electrical drawings.
6.4.5 The mounting location is important to the performance and operating life
of the unit. The environment must be dry and protected from water
ingress.
6.4.6 The installation is straightforward, but it is important each step is done
correctly and safely. A mistake can lead to dangerous voltage and
current levels. Be sure to carefully follow each instruction in this section.
Read all instructions first before beginning installation.
6.4.7 The installation instructions are for installation of a negative grounded
system. National Electrical Code (NEC) requirements are noted on
occasion for convenience, however, the installer should have a complete
understanding of NEC and UL requirements for photovoltaic installations.
The retrofit assembly is accepted as a component of a
NOTE:
fluorescent luminaire where the suitability of the combination shall be
6.4.8
determined by CSA or authorities having jurisdiction.
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
9
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
6.0
Installation and Userʼs Manual
GENERAL REQUIREMENTS
NOTE: Inspect wiring and components for damage when drilling for
installation
of retrofit assembly hardware.
6.4.9
6.5 Recommended Tools
6.5.1 This installation may require the following, depending on the installation
of specific ballasts and existing wiring:
#2 and #0 Phillips screwdrivers
Slotted screwdriver
Wire strippers
Wire cutters
Pliers
10
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
Installation and Userʼs Manual
380VDC, 6-Lamp Ballast Retrofit Kit
INSTALLATION PROCEDURE
7.1 380VDC 6-LAMP BALLAST MODELS
380VDC 6-LAMP BALLAST WIRING DIAGRAM
RED
BLACK
380VDC (+)
380VDC (–)
24VDC (+)
24VDC (–)
SW1-1
SW1-2
SW2-1
SW2-2
380VDC INPUT 32W T8
ELECTRONIC BALLAST
RED
INPUT
R1
R2
B1
B2
B3
B4
7.1.1
BROWN
GRAY
ORANGE 2 Lamp (R)
PURPLE 2 Lamp (R)
ORANGE 4 Lamp (B)
PURPLE 4 Lamp (B)
AUX OUTPUT
32W T8
Y1 Y2
32W T8
32W T8
YELLOW
BLUE
7.0
32W T8
32W T8
32W T8
WARNING - Shock Hazard
At the supply panel, disconnect power to the luminaire(s).
WARNING - Risk of fire or electric shock. Luminaire wiring and
electrical parts may be damaged when drilling for installation of unit.
Check for enclosed wiring and components.
7.1.2
CAUTION: Gain access to the ballast wiring enclosure and remove
all line voltage wiring between existing ballast and the nearest
junction box, including any ground wires and armored cable. If the
luminaire was powered by line voltage from an adjacent luminaire,
remove any line voltage wiring between the luminaires. Cap off any
exposed live leads with included wire nuts.
Figure 7.1 - Example of AC system to be retrofitted.
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
11
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
7.0
Installation and Userʼs Manual
INSTALLATION PROCEDURE
7.1.3 Cut control wires going to the
line voltage ballast, if present.
7.1.4 Cut the lampholder wires at
the ballast, and strip the cut
ends to wire nut
specifications.
7.1.5 Remove the old line voltage
ballast.
7.1.6 Mount the new Nextek
380VDC ballast using existing studs or
screws. If necessary, secure ballasts
using appropriately sized sheet metal
screws. If no existing hole or stud exists
at the correct mounting location, use a
self-tapping sheet metal screw.
7.1.7 For pre-existing mounting studs or
holes:
Figure 7.1.3
Figure 7.1.6
7.1.7.1 Carefully align the ballast slot to one mounting hole or stud and
insert a sheet metal screw with a star washer. The washer is for
enclosure to fixture grounding purposes.
7.1.7.2 Do not tighten the screw completely. Leave a 1/4" (6 mm) gap
between the mounting surface and screw head.
7.1.7.3 Carefully align the ballast slot to one mounting hole or stud and
insert a sheet metal screw.
7.1.7.4 When the ballast is properly positioned, tighten both (2) screws.
7.1.7.5 Proceed to step 7.1.10.
7.1.8 For a surface with no pre-existing mounting studs or holes:
7.1.8.1 Place a mark on the mounting surface for one of the mounting
holes in accordance with the luminaire manufacturer’s
instructions or drawings.
7.1.8.2 Use a self-tapping sheet metal screw to insert the first screw at
the mark.
7.1.8.3 Do not tighten the screw completely. Leave a 1/4" (6 mm) gap
between the mounting surface and screw head.
12
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
7.0
Installation and Userʼs Manual
INSTALLATION PROCEDURE
7.1.8.4 Mark the second mounting hole location for the ballast.
7.1.8.5 Carefully align the ballast slot to the second mounting hole and
insert a sheet metal screw.
7.1.8.6 When the ballast is properly positioned, tighten both (2) screws.
7.1.9
WARNING - Risk of fire or electric shock. Luminaire wiring and
electrical parts may be damaged when drilling for installation of
Fluorescent conversion kit. Check for enclosed wiring and
components.
7.1.10 LAMPHOLDERS:
7.1.10.1 If existing
lampholders
have a wire
shunting the
pins, go to
step 7.1.12.
7.1.10.2 If existing
lampholders
are not
Figure 7.1.10.1
shunted, then
shunt the lampholders with external wire.
Figure 7.1.10.2
Example of shunted lampholder
7.1.11 Connect the lampholder lead wires from the new Nextek ballast as shown
on the Ballast Rewiring Schematic to the lampholder wires from the
luminaire using wire nuts.
See step 7.1.12
for connections
7.1.12 Connect the switch control wires (purple, orange, purple/black stripe, and
orange/black stripe) to switch as described in the Switch Wiring Tables
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
13
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
7.0
Installation and Userʼs Manual
INSTALLATION PROCEDURE
below. If no switching is desired then cap off the orange wires and purple
wires with wire nuts separately.
Switch Type
Normally Open1
Normally Closed
Switchʼs First Contact
Purple(SW1)
Purple/Black striped (SW2)
Orange(SW1)
Orange/Black striped (SW2)
Simple Switch Wiring Table
Switchʼs Second Contact
Gray (SW1 & SW2)
Purple and Gray
(SW1 & SW2)
: The Orange and Orange/Black Striped wires are unused, cap off
NOTE
with wire nuts.
1
Switch Type Pwr in +
Normally
Open2
Normally
Closed
Pwr in –
Brown
Gray
Brown
Gray
Switchʼs First Contact
Purple(SW1)
Purple/Black striped (SW2)
Orange(SW1)
Orange/Black striped (SW2)
Smart Switch Wiring Table
Switchʼs Second Contact
Gray (SW1 & SW2)
Purple and Gray
(SW1 & SW2)
NOTE2: The connection to Gray is not necessary if the Switch is
internally grounded.
7.1.13 The Brown and Gray wires are for the Auxiliary 24VDC supply. The
supply is designed for 24VDC low power devices like smart switches or
the Nextek Power Systems Emergency Ballast. The polarity for the
24VDC supply is the brown lead is +24VDC and the gray lead is -24VDC.
If the Auxiliary supply is not required, then cap off the brown and gray
leads individually.
7.1.14 Connect Nextek 380 Volt DC ballast input leads (black wire (-380VDC)
and white stripped red wire (+380VDC) to a suitably-rated 90ºC conduit
enclosed 380VDC bus line) inside the luminaire with no exposed wiring
(wire must be in conduit) on the outside of the luminaire.
7.1.15 Ballast is grounded to the enclosure and thus the luminaire. Connect the
ground wire to the luminaire via the luminaire’s grounding terminal/screw.
7.1.16 Replace any covers or diffusers removed during the conversion
installation.
7.1.17 Plug any unused openings in the luminaire created by the removal of
branch wiring.
7.1.18 Affix the included sticker to outside of luminaire near ballast access
cover.
14
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
7.0
Installation and Userʼs Manual
INSTALLATION PROCEDURE
7.1.19 Connect the power wire from the luminaire to a 380VDC bus line.
7.1.20 Set Dimming Control to operate as follows:
Switch Type
Dim Level
NO
NC
0%
33%
66%
100%
SW1 Open
SW2 Closed
SW1 Closed
SW2 Open
SW1 Open
SW2 Closed
SW1 Closed
SW2 Closed
SW1 Closed
SW2 Closed
SW1 Open
SW2 Closed
SW1 Open
SW2 Closed
SW1 Open
SW2 Open
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
15
Rev. 052014
380VDC, 6-Lamp Ballast Retrofit Kit
8.0
Installation Manual
NOTES
16
Copyright 2013-2014 all rights reserved by Nextek Power Systems, Inc. in the United States and in other countries throughout the world.
Rev. 052014
For more information:
Nextek Power Systems
461 Burroughs Street
Detroit, Michigan 48202
www.nextekpower.com
Tel: 313-887-1321
Toll free: 1 (877) 24-VOLTS
Fax: 313-887-9433
[email protected]