Download Penn - Electric Fishing Reels by FISH WINCH

FISH WINCH
®
Owner’s Manual
Introduction
Thank you for purchasing your FISH WINCH® electric fishing reel drive. Your new FISH
WINCH® is an electric motor drive attachment that quickly converts your conventional reel into a
powerful electric fishing reel. Fishing reels featuring a FISH WINCH® make great electric
bottom fishing (deep dropping) reels, electric trolling reels, electric kite reels, electric teaser reels,
or electric dredge reels. Please be careful when using the FISH WINCH® as they are very
powerful and can pull you overboard. We hope that you enjoy the pleasant experience of fishing
with your new electric reel. Please read this manual carefully and retain it for future reference.
Power Switch
Your FISH WINCH® is equipped with an all-in-one momentary or “continuous-on” power switch.
Push or pull the lever (button lock) on the switch housing over top of the momentary push button
to make it a “continuous-on” switch.
Wiring
Red/White = Positive (+)
Black = Negative (-)
Installation Instructions
The FISH WINCH® is very easy to attach to your reel. Please follow the instructions below for
quick and easy installation:
1 - Remove the handle from your reel (2-speed reels should be in high gear) and tighten the drag.
2 - With the reel sitting flat, remove the screws on your reel (outer edge of reel) located on most
reels at 5 o’clock (5:00) and 7 o’clock (7:00) - *screws on the 320LD/320GT’s are located at
(4:00) & (6:00) - screws on the 340GT/GTi & 345GT/GTi are located at (4:00) & (5:00) screws on the FATHOM (star drag), GRAPHITE GS/MAG, & SQUALL (single speed) reels
are located at (7:00) & (9:00) - screws on the 113HN BAJA, US SENATORS, & WARFARE
are located at (3:00) & (6:00). Screws on the FTH40NLD(HS), FTH60LD2, & TRQ40NLD2 are
located at (2:00) & (6:00)*
3 - Connect your FISH WINCH® to a 12 volt power source.
4 - Carefully line up the driveshaft of the FISH WINCH® to the shaft of the reel (where the
handle was attached). *Penn 10KG, 10LD, 15KG, 15LD, 245LD, 24KG, 309, 320LD, 330LD,
340GT, 345GT, 340GTi, 345GTi, 40GLS, 45GLS, FATHOM, GLD, INTERNATIONAL, LONG
BEACH, SQL16VS, SQL30VSW, & SQL50VSW require the enclosed spacers to be placed
into the screw holes of the reel before attaching the FISH WINCH®.*
5 - Slowly and carefully, using the power button on the FISH WINCH®, thread the unit’s
driveshaft into/onto the shaft of the reel. You may have to hold the reel’s spool while threading
the driveshaft. Be careful not to cross thread the two parts. (Should you accidentally cross
thread the driveshaft into/onto the reel, simply reverse the positive (+) and negative (-) from
your power cord on your power source to reverse the motor).
6 - Disconnect the FISH WINCH® from the power source.
7 - Replace the screws removed earlier with the enclosed screws using the wrench or screwdriver
provided.
8 - To remove the FISH WINCH® from your reel, simply remove the screws attaching the
mounting bracket to your reel. Connect your FISH WINCH® to a 12 volt power source
reversing the positive (+) and negative (-) of your power cord. Hold your reel tightly and
engage the power button.
Important Instructions & Information
1 - Keep fingers, clothing, hair, loose jewelry, etc. away from the star drag when using the
FISH WINCH®.
2 - Use only the voltage specified on the FISH WINCH® (12V or 24V DC only). Using any
voltage other than what is specified can harm the FISH WINCH® and will void the warranty.
3 - In no event shall Lagerstone LLC be liable for any incidental, special, indirect, or
consequential damages resulting from the use, misuse, or inability to use the product
or from defects in the product.
Care & Maintenance
Use freshwater to rinse off your FISH WINCH® after use. Do not submerge it under water or
use harsh cleaners/abrasives when cleaning. The FISH WINCH® is sealed in a rubber coating
while the driveshaft, mounting bracket, and screws are 304 stainless steel.
Limited Warranty
Each FISH WINCH® is inspected and tested before leaving our facility. It is guaranteed against
mechanical defects in material and workmanship for a period of three (3) years from the original
date of purchase. Electrical components consisting of the electric motor, power switch(s), and
power cord are guaranteed for a period of one (1) year from the original date of purchase.
Repairs or parts replacement required as a result of any defects will be made free of charge
during this warranty period. In all other cases, the FISH WINCH® will be repaired (if possible)
and returned to the customer upon payment of a reasonable service charge, costs of any parts
replaced, and shipping costs.
This guarantee does not cover normal expected wear, chips, scratches, damage, or malfunctions
caused by abuse, misuse, negligence, accidents, alterations, or use of current or voltage other
than what is labeled on the FISH WINCH®. This warranty also excludes any reel that may have
been used in conjunction with the FISH WINCH®.
This limited warranty does not obligate us to replace or refinish the FISH WINCH® unit and is in
lieu of any other warranty either expressed or implied.
Please take a moment to record the following information:
- FISH WINCH® purchase date: _________________________
- Purchase location: ____________________________________
- Serial number: _______________________________________
Service Policy & Procedure
Lagerstone LLC provides prompt service on all of our products. Should service be required,
please call us for a “Return Authorization Number”. Please return your FISH WINCH® postage
prepaid, with a description of the problem & contact phone number to our mailing address below:
_____________________________________________________________________________
Lagerstone LLC
PO Box 11407
Wilmington, NC
(910) 470-2888
www.FishWinch.com
_____________________________________________________________________________
Matthew 4:19 - Jesus said to them, “Follow Me, and I will make you fishers of men”.