Download Modeling of Electrical Characteristics of Photovoltaic Cell

Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
Modeling of Electrical Characteristics of Photovoltaic Cell
Considering Single-Diode Model
M. Azzouzi, D. Popescu, and M. Bouchahdane

resistances which is called 1M5P.
Abstract—Solar energy is one of the most important types of
renewable energies. Many models of solar cell had been
proposed since the beginning of the solar energy exploitation.
The present paper focuses on single-diode photovoltaic cell
models. The I-V and P-V characteristics are presented for each
model in function of the series resistance, the shunt resistance,
the temperature and the irradiation. More than that, a
comparison between an ideal model single-diode solar cell, a
model of single-diode solar cell with a series resistance and a
model of single-diode solar cell with series and shunt resistances
is also presented. Different results were visualized and
commented and a conclusion had been drawn.
A. Ideal Solar Cell (1M4P)
The I-V characteristics of a solar cell have an exponential
characteristic similar to that of a diode [3]. The ideal
equivalent circuit of solar cell is a current source in parallel
with a single-diode. This model involves the following four
unknown parameters: m, Iph, and Is, this model is also called
1M3P (Single Mechanism, Three Parameters). The
configuration of the simulated ideal solar cell with
single-diode is shown in Fig. 1.
Ipv
Index Terms—PV cell, solar energy, single diode, modeling,
I-V/P-V characteristics, 1M3P, 1M4P, 1M5P.
Id
In recent years, significant photovoltaic deployment has
occurred, particularly in many developed countries. Also, PV
energy is going to become an important source in coming
years it has highest source of sunshine radiation. This last is
composed of photons of different energies, and some are
absorbed at the PN junction. Photons with energies lower
than the band gap of the solar cell are useless and generate no
voltage or electric current. Photons with energy superior to
the band gap generate electricity, but only the energy
corresponding to the band gap is used [1].
Solar cells are basically made of semiconductors which are
manufactured using different process. These semiconductors
convert the energy of sunlight directly into electricity by the
photovoltaic effect. Many mathematical models have been
developed to represent the highly nonlinear behavior
resulting from semiconductor junctions in order to assess the
performance of the PV cell. In our case, we consider single
diode model [2].
Fig. 1. Equivalent model of single diode ideal solar cell (1M3P).
The characteristic equation is deduced directly from the
Kirchhoff law:
(1)
) so the output
(
The diode current is
current is presented by the following non linear I-V equation:
)
(
(2)
For the same irradiation and PN junction temperature
conditions, the short circuit current Isc is the greatest value of
the current generated by the cell and the open circuit voltage
Voc is the greatest value of the voltage at the cell terminals [3].
They are given by:
II. MODELING OF SINGLE DIODE SOLAR CELL
Equivalent circuit models define the entire I-V curve of a
cell, module, or array as a continuous function for a given set
of operating conditions. Three equivalent circuit models can
be used to describe a single diode model such as: the ideal
solar cell or the 1M4P model, solar cell with series resistance
called also 1M5P, and solar cell with series and shunt
(3)
for Vpv=0
(
)
(4)
)]
(5)
for Ipv=0
The output power is:
Manuscript received March 17, 2015; revised September 16, 2015.
M. Azzouzi and M. Bouchahdane are with Ziane Achour University of
Djelfa, Cite Ain Chih BP 317, Algeria (e-mail: [email protected]).
D. Popesscu is with the Department of Automatic Control and Systems
Engineering, Faculty of Automatic Control and Computers, University
Politenica of Bucharest, Splaiul Independentei 313, 060042, Bucharest,
Romania (e-mail: [email protected]).
doi: 10.18178/jocet.2016.4.6.323
Vpv
Iph
I. INTRODUCTION
[
414
(
Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
B. Solar Cell with Series Resistance
More accuracy can be introduced to the model by adding a
series resistance. The electric scheme equivalent to this
model is shown in Fig. 2. This model involves the following
four unknown parameters: m, Iph, Rs and Is model which is
also called 1M4P (Single Mechanism, Four Parameters) [4].
And the shunt current is:
The relationship between the PV cell output current and
terminal voltage according to the single-diode model is
governed by equation:
(
The diode current is:
(
)
(
)
)
A. Influence of Irradiation and Temperature
In the three models, the temperature is maintained constant
at 25°C and by varying the irradiation (250W/m2, 500W/m2,
750W/m2, 1000W/m2). Fig. 4 shows the Matlab program
results under these conditions on I-V and P-V characteristics
respectively. It is clear that current generated by the incident
light depends on irradiation, the higher the irradiation, the
greater the current. On the other hand, voltage is staying
almost constant and it is not going to. The influence of
irradiation on maximum power point is clear, the higher the
irradiation, the major of the maximum power point will be
[6].
Second, the irradiation is maintained constant at
1000W/m2 and varying temperature (25°C, 50°C, 75°C,
100°C) will generate the characteristic curves.
Fig. 5 show the simulation results of I-V and P-V
characteristics respectively under the same conditions. The
current generated by the incident light is going to stay
constant although it increases slightly while the voltage
decreases.
The effect of the temperature increase decreases voltage
and power. Fig. 6 shows the influence of both the irradiation
and the temperature, we can remark that the I-V and P-V
curves are similar to these of the irradiation influence with
slightly higher values of power; the effect of the temperature
in this case is almost ignored [5].
(6)
C. Solar Cell with Series and Shunt Resistances (1M5P)
The photovoltaic cell in this case is represented by the
circuit of Fig. 3 which consists of a current source modeling
the light flux, the losses are modeled by two resistances:
shunt resistance, and series resistance. The model thus
involves the following five unknown parameters: m, Iph, Rs,
Rsh and Is. This model is also called 1M5P (Single
Mechanism, Five parameters) [4].
B. Influence of Series Resistance and Temperature
Fig. 7 shows the influence of the serial resistance on the
characteristic I-V and P-V of 1M4P and 1M5P photovoltaic
cells. The series resistance is the slope of the characteristic in
the area where the PV cell behaves as a voltage generator it
does not change the open circuit voltage, and when it is high,
it decreases the value of the short circuit current. The increase
of the series resistance results in a decrease in the slope of the
power curve. The influence of both the series resistance and
the temperature on the same previous models is presented in
Fig. 8, where the short circuit current took the same value
while the open circuit voltage is increased [5].
Fig. 3. Equivalent model of single diode solar cell with series and shunt
resistances (1M5P).
The characteristic equation can be deduced directly by
using the Kirchhoff law:
(7)
where the diode current is:
(
)
(8)
III. INFLUENCES OF ENVIRONMENTAL AND PHYSICAL
PARAMETERS
For the same irradiation and PN junction temperature
conditions, the inclusion of a series resistance in the model
implies the use of a recurrent equation to determine the
output current in function of the terminal voltage. A simple
iterative technique initially tried only converged for positive
currents [5].
(
)
)
Therefore, the I-V characteristics of the solar cell with
single-diode and series resistance are given by:
(
)
For the same irradiation and PN junction temperature
conditions, the inclusion of a series resistance in the model
implies the use of a recurrent equation to determine the
output current in function of the terminal voltage. A simple
iterative technique initially tried only converged for positive
currents [6].
The modeling of the PV cell in the three cases was done
applying the previous equations. Many types of simulation
are carried out depending on the chosen model and the
selected parameters.
Fig. 2. Equivalent model of single diode solar cell with series resistance
(1M4P).
(
(
)
415
Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
Fig. 4. Influence of the irradiation.
Fig. 5. Influence of the temperature.
Fig. 6. Influence of temperature and irradiation.
Fig. 7. Influence of series resistance.
416
Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
Fig. 8. Influence of series resistance and temperature.
Fig. 9. Influence of series resistance and irradiation for 1M4P model.
Fig. 10. Influence of series resistance and irradiation for 1M5P model.
source of current [8] (see Fig. 12).
C. Influence of Series Resistance and Irradiation
The Fig. 9 and Fig. 10 show the importance of the series
resistance, which indicates the difference between the
different models. In Fig. 10, the performance of a 1M4P PV
cell is much degraded when Rs and the irradiation are high,
on the other side the model 1M5P is not so influenced by the
series resistance as the 1M4P model [7].
E. Influence of Shunt and Series Resistances
Fig. 13 shows the effect of the two resistors series and
parallel at the same time, where it can be concluded that the
effect of the series resistance is negligible, relative to the
shunt resistance. A minimization of the value of the shunt
resistance induces an estrangement from the real operation of
the cell [9].
D. Influence of Shunt Resistance and Temperature
The shunt resistance is a resistance which takes into
account the unavoidable leakage of current that occurs
between the terminals of a solar cell. In general, when the
shunt resistance is very high, its effect is felt especially in the
generation of power. The influence of the shunt resistance on
the current-voltage characteristics results in a slight decrease
in open circuit voltage and an increase of the slope of the I-V
curve of the cell in the area corresponding to operation as a
F. Influence of Shunt Resistance and Irradiation
Fig. 14 presents the simultaneous influence of shunt
resistance and the irradiation on a 1M5P model, from which
we can collude that the I-V and P-V characteristics are
similar to these of the shunt resistance influence shown in Fig.
11, with the same values of short circuit current and open
circuit voltage, so the shunt resistance influence in this case
was been ignored relative to the irradiation influence.
417
Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
Fig. 11. Influence of shunt resistance.
Fig. 12. Influence of shunt resistance and temperature.
Fig. 13. Influence of shunt and series resistance.
Fig. 14. Influence of shunt resistance and irradiation.
418
Journal of Clean Energy Technologies, Vol. 4, No. 6, November 2016
Fig. 15. Comparison between the three models of single diode PV cell.
E[W/m2] is the irradiation
Rs[Ω]: series resistance
Rsh[Ω]: shunt resistance
m: the ideality factor of the diode
IV. COMPARISON BETWEEN THE THREE MODELS
The same reference condition is selected for each model.
The performance of the solar cell is normally evaluated in the
test normalizes conditions (STC), the irradiation is
normalized to 1000W/m2, and temperature to 25oC. Fig. 15
presents a comparison between different models of single
diode PV cell from which we can note that 1M3P has the
optimized performances of the single diode model with
higher values of current and power, contrariwise the 1M5P
gives the lower values of current and power, hence the 1M4P
curves proves that it is the most accurate model since it is
closer to the real operation of the PV cell [10]-[13].
REFERENCES
[1]
[2]
[3]
[4]
[5]
V. CONCLUSION
In this paper, we have presented the fundamental electric
characteristics of photovoltaic cell of single diode where all
the equivalent circuits were described, and the equivalent
models were discussed. A comparison between these models
demonstrated that the solar cell with series resistance model
(1M4P) offers a more realistic behavior for the photovoltaic
systems while it combines between the simplicity and the
precision. The single diode model was analyzed in function
of physical phenomena such as the resistance series and the
resistance shunt, and the environmental parameters as the
irradiation and the temperature.
[6]
APPENDIX
[12]
[7]
[8]
[9]
[10]
[11]
PV: Photovoltaic
I-V: current-voltage
P-V: power-voltage
1M3P: single mechanism, three parameters
1M4P: single mechanism, four parameters
1M5P: single mechanism, five parameters
Iph[A]: the current generated by the incident light
Is[A]: the diode reverse bias saturation current
Ish[A]: the shunt resistance current
Isc[A]:short circuit current
Ipv[A]: the output current
Vpv[V]: the terminal voltage
Vph[V] :the photovoltaic voltage
Id[A] : the diode current
Voc[V]: open circuit voltage
q: the electron charge [1.60217646×10-19C]
k: the Boltzmann constant [1.3806503×10-23J/K]
T[K]: the temperature of the PN junction
[13]
J. Bikaneria et al., “Modeling and simulation of PV cell using
one-diode model,” IJSRP, vol. 3, issue 10, 2013.
N. Belhaouas, M. S. A. Cheikh, A. Malek, and C. Larbes,
“Matlab-Simulink of photovoltaic system based on a two-diode model
simulator with shaded solar cells,” Revue des Energies Renouvelables,
vol. 16, no. 1, pp. 65-73, 2013.
E. M. G. Rodrigues et al., “Simulation of a solar cell considering
single-diode equivalent circuit model,” in Proc. International
Conference on Renewable Energies and Power Quality, 2011.
B. Bentouati, “Etude comparative de deux cellules photovoltaïques,”
Master in Automatic Control, University of Djelfa, 2012.
B. Alsayid, “Modeling and simulation of photovoltaic
cell/module/array with two-diode model,” IJCTEE, vol. 1, no. 3, 2012.
D. Bonkoungou, Z. Koalaga, and D. Njomo, “Modelling and
Simulation of photovoltaic module considering single-diode equivalent
circuit model in MATLAB,” International Journal of Emerging
Technology and Advanced Engineering, vol. 3, issue 3, 2013.
T. Salmi et al., “MATLAB/Simulink based modeling of solar
photovoltaic cell,” International Journal of Renewable Energy
Research, vol. 2, no. 2, 2012.
K. Hellali, “Modelisation d’une cellule photovoltaique: etude
comparative,” Master in Electrotechnique, Universite Mouloud
Mammri de Tizi-Ouzou, 2012.
A. O. M. Yahya et al., “Etude et modélisation d’un générateur
photovoltaï
que,” R. des Energies Renouvelables, vol. 11, pp. 473-483.
Z. Zhao, “1D modeling of solar cells,” Columbia University.
Single Diode Equivalent Circuit Models. [Online]. Available:
http://pvpmc.org/modeling-steps/module-iv-curve/diode-equivalent-ci
rcuitmodels/
Electrical
engineering.
[Online].
Available:
http://www.ee.columbia.edu/~lavaei/Projects/ZZ.pdf
CSI,
Inc.
[Online].
Available:
http://www.californiascientific.com/resource/Solar%20Cell.pdf
Messaouda Azzouzi was born in Djelfa, Algeria in
1980, she got her baccalaureate degree in natural
and life sciences form Belahrach Said Hight Schoul
in Djelfa in 1997, engineering diploma in
electronics from Ziane Achour University of Djelfa,
Algeria in 2002. As a major of the 2002 promotion,
she took a Romano-Algerian doctoral scholarship,
and finished her PhD thesis in automatic control
form Politehnica University of Bucharest, Romania
in 2008.
She worked as an assistant professor at the Ziane Achour University of
Djelfa, Algeria from November 2008 to December 2010. Presently, she is
an associate professor at the Ziane Achour University of Djelfa, Algeria.
Dr. Azzouzi has publications in many journals and she participated in
many international conferences. She served as the reviewer and editor of
known journals and she joined as an organizing/scientific/international
program committees member of many international conferences.
Recently, she was elected as the IEEE Algeria Subsection secretary.
419
Optical and Combustion Energy