* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Your will begin in a moment. If it doesn`t, restart
Three-phase electric power wikipedia , lookup
Spectral density wikipedia , lookup
Power factor wikipedia , lookup
Wireless power transfer wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Standby power wikipedia , lookup
History of electric power transmission wikipedia , lookup
Buck converter wikipedia , lookup
Voltage optimisation wikipedia , lookup
Electric power system wikipedia , lookup
Audio power wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Electrification wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Alternating current wikipedia , lookup
Power over Ethernet wikipedia , lookup
Opto-isolator wikipedia , lookup
Power engineering wikipedia , lookup
Distribution management system wikipedia , lookup
Power supply wikipedia , lookup
Mains electricity wikipedia , lookup
TVHUNTER + QUICK START GUIDE ISDB-T/TB FRONT VIEW USB RF 1 2 3 5 4 6 7 1 Input RF connector 4 IDENTIFICATION key 2 Display 5 Power input connector 3 DETECTION/CONFIGURATION key 6 USB connector 7 ADJUST key SCREEN ICONS REFERENCE STATUS BAR TB TB ISDB-T/TB signal not locked. Power supply connected. ISDB-T/TB signal locked. Battery power level. Manual power off enabled. USB Connected to PC through the USB port. 5/12/15/24/OFF External voltage supplied through the RF connector (5V/12V/15V/24V/OFF) SWITCHING ON/OFF Switch on the TVHUNTER + pressing If you press or , or for four seconds. for more than eight seconds when starting, it enables manual power off mode. TVHUNTER + ISDB-T/TB PDF Find the user’s manual on the download area at: www.promaxelectronics.com USER MANUAL DOWNLOAD TVHUNTER + QUICK START GUIDE ISDB-T/TB DETECTION Plug the TVHUNTER + to the antenna socket and turn the antenna until the TVHUNTER + shows the maximum power on the display. To avoid damage to other devices, when switching on the equipment, the external power supply is always OFF by default. Select the external power through the setup menu and press to switch between 0V (OFF) and the selected external supply voltage. RF 1)DETECT External power supply OFF Maximum measured power Current power PRESS DETECT MAX POWER RATE: POWER RATE: 41% 40% PRESS DETECT TO SWITCH THE EXTERNAL SUPPLY VOLTAGE (see CONFIGURATION) 1)DETECT 5V MAX POWER RATE: POWER RATE: 41% 40% NOTE: Once the antenna is aligned using the Detection mode, if it is unknown the channels that can be received at the location, it is advisable to "Auto-Scan" and save the results (see Configuration). 6 TVHUNTER + QUICK START GUIDE ISDB-T/TB IDENTIFICATION Press and wait until locking the signal. The display will show the parameters of the stored test point (selected name and frequency), the name of multiplex channel tuned and its services identified at this test point. To change to another test point or layer (A: one layer; A+B: two layers; A+B+C: three layers) press again. Sequential number of the test point Test Point Name Tuned channel name Identified services RF Locked signal (black background) )IDENTIFY 21)DETECT OFF 5V T B TP04:A C66 FR: 531.0MHz NET:PROMAX TV SERVICE LIST: 1 PROMAX CH01 MAX POWER RATE: 41% POWER RATE: 40% PRESS IDENTIFICATION PRESS SHORT PRESS: NEXT TEST POINT OR LAYER LONG PRESS <1s: PREVIOUS TEST POINT OR LAYER RF 2)IDENTIFY OFF 1)DETECT 5V T B TP04:B C66 FR: 531.0MHz NET:PROMAX TV SERVICE LIST: 1 PROMAX CH01 MAX POWER RATE: 41% POWER RATE: 40% TP00 TB TP00:A TP00:B TP00:C TP01 Short Key Press [2] TB + Long Key Press [2] 7 TVHUNTER + QUICK START GUIDE ISDB-T/TB ADJUST Press to perform fine-tuning. Check that every access point in the installation is meeting the criteria established by current regulations. To measure another test point or layer (A: one layer; A+B: two layers; A+B+C: three layers) press again until finding the test point you are looking for. Each layer has different parameters and therefore, different measures. TV FM Sequential number of the test point Test Point Name RF Locked signal (black background) 1)DETECT 5V T B OFF 3)ADJUST TP04:A C66 FR:531.0MHz POWER: 79.5dBuV MER:35 .0dB LM:>20.2dB 35 0 1.0E-5 41% MAXCBER: POWER RATE: VBER: 1.0E-8 40% POWER RATE: PRESS ADJUST PRESS SHORT PRESS: NEXT TEST POINT OR LAYER LONG PRESS <1s: PREVIOUS TEST POINT OR LAYER CONFIGURATION At the DETECTION screen, press and hold until appears the configuration menu. 1)DETECT )SETUP 5V OFF 1)CANCEL 2)OPTION START AUTO SCAN EXTERNAL SUPPLY SOUND CONTROL BACKLIGHT MODE MAX POWERLCD RATE: CONTRAST POWER RATE:& EXIT CONFIRM 3)SELECT Navegation Keys: OFF ON AUTO 41% 40% It exits the configuration menu without saving changes It scrolls along the menu options It changes the parameter/Accepts Start Auto Scan: It starts the auto-scan function. External Supply: It allows selecting the external supply voltage for the antenna among 0V (OFF, by default), 5V, 12V,15V or 24V. Confirm & Exit: It applies and saves the changes made and exits the configuration menu. When using the TVHUNTER +, it may appear on the display some messages and icons, depending on the status or event is taking place. These messages and icons are detailed below MESSAGE DESCRIPTION MESSAGE DESCRIPTION “LOW BATTERY” Low power level battery. Plug it to the charger. “SERVICES NOT FOUND” The instrument cannot detect the services of a network. “VERY LOW BATTERY” The equipment will be switched off immediately. “SIGNAL NOT DETECTED” When no signal is detected. “SUPPLY SHORT CIRCUIT” The external supply can be shortcut. “FULL BATTERY” Battery fully charged. “SUPPLY OVER CURRENT” The external supply has a high current consumption. “MPEG-2 NOT DETECTED” It is not detecting the Transport Stream MPEG-2 signal. “MANUAL POWER OFF” The instrument has to be switched off by hand. The instrument will switch off after five minutes of inactivity. “LOADING NETWORK” “AUTO POWER OFF” “BATTERY MODE” When the battery is being charged. “UPDATE MODE” When the instrument is being updated. “NETWORK NOT FOUND” The instrument cannot find a TV network. After finding a signal, needs a time to load the network. “LOADING SERVICES” After finding a network, needs a time to load services. “HIGH TEMPERATURE” The operation temperature is too high. The instrument must be switched off for a while. If the problem persists, contact with the technical support. v1.04.02 Find the user’s manual on the download area at: www.promaxelectronics.com (0 DG0103) 01/03/2013