Download Soldering iron

Soldering iron
•
•
•
High-performance soldering iron that, in the pursuit both "usability" and "appearance",
has evolved beyond being a mere working tool
Compact design has drastically reduced footprint
Use of special driver (possible to be stored in the main unit) for thermal correction
reduces the load on a temperature control knob
Model No. Unit Color
Iron Holder Color Packing List
No.FX888 Blue-Yellow Blue-Yellow
Model No.
FX888
Power consumption 70W
Temperature range 200-480ºC
Temperature stability ±1ºC at idle temperature
・Station
Output voltage 26V
Dimensions 100(W)×120(H)×130(D)mm
1.3kg
Weight
Soldering station (FX-888),
Soldering iron (FX-8801 with
soldering tip type B), Iron holder
(with cleaning wire, cleaning
sponge and rubber cleaner),
Hexagon wrench, CAL adjustment
driver, Instruction Manual
・Soldering Iron
Power consumption 65W (26V)
Tip to ground resistance <2Ω
Tip to ground potential <2mV
Shape-B (No.T18-B)
Standard tip
Ceramic heater
Heating element
1.2m
Length of cord
217mm (with B tip)
Total length
46g (with B tip)
Weight
* Length and weight (w/o cord)
Full design changes for HAKKO 936
High-performance soldering iron pursuing "usability" and "appearance" has
evolved into more than a mere working tool.
Temperature controller achieves 3 factors such as "space saving", "good
maintainability" and "good safety and stability"
·Footprint was reduced by approx. 50% compared to that of conventional
HAKKO 936.
·Use of special driver (resin) for thermal correction during daily inspection
maintains durability.
·The temperature control knob can be locked to prevent the setting
temperature from changing during the work.
How to lock the temperature control knob
Soldering iron provides 30% increase in workability compared to that of
conventional HAKKO 936.
·Improved thermal conductivity enables the same work to be performed in a
shorter time. (Refer to the workability comparison graph.)
·The rise time is 20 seconds faster and drop in tip temperature during work is
reduced. (Refer to the thermal characteristics graph.)
Workability comparison graph
Thermal characteristics graph
The internal structure and tip shape
were reviewed to provide better
thermal conductivity and better
thermal efficiency. As a result, the
time for performing the same work
was greatly shortened.
It was demonstrated that the rise
time is approx. 20 seconds faster,
and the drop in tip temperature
during continuous work is reduced.
·Employment of separated-heater tip achieves low running cost.
·Making the element cover thinner enables better viewing during work and
easier working even on a P.W.B. with highly dense components.
Iron holder provides 3 cleaning methods and low-noise effect
·Sound and vibration generated when placing the iron into the iron holder were
reduced by 30%.
·Three types of cleaning methods are available in one iron holder using a
cleaning sponge, cleaning wire and rubber cleaner.
·The detachable waste holder at the bottom of iron holder offers an easy way to
dispose of the waste.
·
Ultra-compact size with consideration of environment and ease of use
Space-saving design leaves working area large even in a cell-production site.
* The conventional product shown in the photo is HAKKO 936.
HAKKO FX-8802 N2 (nitrogen) gas system
A space-saving N2 system. Anti-oxidation and
pre-heating significantly improve solderability.
—Example Configuration (N2 System)
Soldering station, Iron holder, N2 gas generator, and N2 flowmeter must
be purchased separately.
HAKKO FX-8803 One-hand, manual-solder-feed iron
— Example Configuration (One-hand, Manual-Solder-Feed System)
Soldering station and Iron holder must be purchased separately.
HAKKO FX-8804 Hot tweezers
—Example Configuration (Hot Tweezer System)
Soldering station, cap, and Iron holder must be purchased separately.
Tips for using HAKKO FX-888.
1. How to remove the bottom plate.
1. Press the slide lock button inward.
Note Press it firmly from upward. It is easy to
open by the slide lock sloping inward.
2. Open the iron holder base while pressing the
slide lock.
3. Remove the solder waste in the bottom plate.
2. How to lock the temperature control knob
The temperature control knob can be locked to
prevent the setting temperature from changing
during the work. In case of locking it, please
insert the hexagon wrench into the lower hole
and tighten the hexagon screw in the hole
counterclockwise.
As for unlocking, don't touch the upper
hole. Adjust by the upper hole makes the
control knob loosen.
T18 Series
Shape BC/C
This type has a shape like a cone or column cut at a slant, which allows users to select the cut
surface size depending on the workpiece.
It is used for drag soldering and pre-tinning of lead wires.
T18-C05 Shape-0.5C
•
•
•
•
T18-C08 Shape-0.8C
T18-C1 Shape-1C
T18-C2 Shape-2C
T18-C3 Shape-3C
•
•
•
•
•
•
•
T18-C4 Shape-4C
T18-C5 Shape-5C NEW
T18-CF1 Shape-1CF
Tinned cut surface only
T18-CF15 Shape-1.5CF
Tinned cut surface only
T18-CF2 Shape-2CF
Tinned cut surface only
T18-CF3 Shape-3CF
Tinned cut surface only
T18-CF4 Shape-4CF
Tinned cut surface only
•
•
T18-CSF25 Shape-2.5CSF
This type has good heat transfer with short tip end design, tinned cut surface ony.
T18-S6 Shape-S6 NEW
Shape B
All-round type which can be used from any direction and is easy to hold at any position.
Possible to solder any surface from small to large.
•
•
•
•
T18-B Shape-B
T18-BL Shape-BL NEW
T18-S4 Shape-S4 NEW
T18-SB Shape-SB
Shape D
This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the
tip in 2 ways: line and face.
The width (size of tip) suitable for the workpiece can be selected, and it can be used for any
soldering work.
•
•
•
•
•
•
T18-D08 Shape-0.8D
T18-D12 Shape-1.2D
T18-D16 Shape-1.6D
T18-D24 Shape-2.4D
T18-D32 Shape-3.2D
T18-DL12 Shape-1.2DL NEW
•
•
•
•
T18-DL2 Shape-2DL NEW
T18-DL32 Shape-3.2DL NEW
T18-S3 Shape-S3 NEW
T18-S9 Shape-S9 NEW
Shape I
This type has a thin conical end and is an ultrafine tip which is best suited for soldering at
narrow pitches, etc.
It is the best for soldering micro components such as 0603, etc. and for repairing high-densitymounting P.W.Bs. such as in cellular phones, etc.
•
T18-I Shape-I
Shape J
This type differs from Shape B and I by bending the tip end and is capable of soldering by
applying the tip in 2 ways: face and point.
It is used for drag soldering and correction of bridging.
•
T18-BR02 Shape-0.2BR NEW
Shape K
This type has a shape like a knife and is capable of soldering by applying the tip in 3 ways:
line, face and point.
It is used for soldering at narrow pitches, correction of bridging and drag soldering.
•
T18-K Shape-K
Part No.
Name
FH800-01SV Iron holder
Specifications
silver
FX8801-01
Soldering iron FX-8801 65W (26V)
B3466
CAL adjustment driver
B2017
Hexagon wrench
A1561
Cleaning wire
B3474
Rubber cleaner
A1560
Heating element
B3469
Tip enclosure
A1559
Cleaning sponge
B1785
Nut
B2022
Nipple
65W (26V)