* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download GT3 Series Multi-function Timers
Power inverter wikipedia , lookup
Electrical substation wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Stray voltage wikipedia , lookup
Electrification wikipedia , lookup
Electric power system wikipedia , lookup
Power over Ethernet wikipedia , lookup
Phone connector (audio) wikipedia , lookup
History of electric power transmission wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Audio power wikipedia , lookup
Voltage optimisation wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Power MOSFET wikipedia , lookup
Power engineering wikipedia , lookup
Alternating current wikipedia , lookup
Power electronics wikipedia , lookup
Buck converter wikipedia , lookup
Mains electricity wikipedia , lookup
Distribution management system wikipedia , lookup
Opto-isolator wikipedia , lookup
GT3 Series Multi-function Timers Wide Variety Including OFF Delay and StarDelta Types • Universal AC power voltage 100 to 240V AC • Solid-state CMOS circuitry ensures high accuracy • Easy-to-view operation indicator • DIN 48mm square panel mount adapter for snap mounting • Complies with safety standards. UL/c-UL listed. • Complies with EN standard [Multi-mode Type] • Instantaneous operation at zero setting • Multi-mode, and universal AC power voltage cover 96 types by one timer Type List For details, see pages 1067 to 1072. Multi-Mode Type Operation Mode On Delay Interval ON Cycle OFF Cycle ON Type GT3A-1 Contact Delayed SPDT GT3A-2 Delayed SPDT + Instantaneous SPDT GT3A-3 Delayed DPDT ON Delay Cycle Signal ON/OFF Delay Signal OFF Delay With Input GT3A-4 Interval ON One Shot Cycle Signal ON/OFF Delay Signal OFF Delay With Input GT3A-5 One Shot One Shot ON Delay One Shot Signal ON/OFF Delay With Input GT3A-6 Delayed DPDT (11P) Time Range 0.1 sec to 180 hours 0.1 sec to 180 hours Output 240V AC, 3A 120V AC/ 30V DC, 5A 240V AC/ 24V DC, 5A 240V AC/ 24V DC, 5A Operation Mode With Reset Input Power OFF Delay Without Reset Input Type Contact GT3F-1 Delayed SPDT GT3F-2 Delayed DPDT Time Range 0.1 sec to 600 sec Output 250V AC/ 30V DC, 5A 250V AC/ 30V DC, 3A Type GT3S-1 Star-Delta GT3S-2 Contact Delayed Star: SPST-NO Delta: SPST-NO Delayed Star: SPST-NO Delta: SPST-NO Instantaneous: SPST-NO Time Range Star: 0.05 to 100 sec Star-Delta: 0.05 sec 0.1 sec 0.25 sec 0.5 sec Output GT3A-4AF20 24V AC/24V DC GT3A-4AD24 100 to 240V AC GT3A-5AF20 24V AC/24V DC GT3A-5AD24 100 to 240V AC GT3A-6AF20 24V AC/24V DC GT3A-6AD24 Operating Voltage 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC Operating Voltage Type No. GT3F-1AF20 GT3F-1AD24 GT3F-2AF20 GT3F-2AD24 Type No. GT3S-1AF20 250V AC/ 30V DC, 5A 100 to 240V AC GT3S-2AF20 For details, see pages 1077 to 1078. Twin-Timer Type Serial Activation Coarse/Fine Adjustment Setting Instantaneous Cycle Cycle Cycle Inversion Interval ON Interval ON Delay Serial Interval ON 100 to 240V AC For details, see pages 1075 to 1076. Star-Delta Type Operation Mode Type No. GT3A-1AF20 GT3A-2AF20 GT3A-2AD24 GT3A-3AF20 GT3A-3AD24 For details, see pages 1073 to 1074. OFF Delay Type Operation Mode Operating Voltage 100 to 240V AC 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC Type Contact Time Range Output T1: 0.1 sec to 6 hours T2: 0.1 sec to 6 hours GT3W-A Delayed SPDT + Delayed SPDT T1: 0.1 sec to 6 hours T2: 0.1 sec to 300 hours 240V AC, 3A T1: 0.1 sec to 300 hours T2: 0.1 sec to 6 hours 120V AC/ 30V DC, 5A T1: 0.1 sec to 300 hours T2: 0.1 sec to 300 hours Operating Voltage 100 to 240V AC Type No. GT3W-A11AF20N 24V AC/24V DC GT3W-A11AD24N 100 to 240V AC GT3W-A13AF20N 24V AC/24V DC GT3W-A13AD24N 100 to 240V AC GT3W-A31AF20N 24V AC/24V DC GT3W-A31AD24N 100 to 240V AC GT3W-A33AF20N 24V AC/24V DC GT3W-A33AD24N 1066 IDEC1066-1085.indd 1066 07.8.17 4:09:54 PM GT3 Series [Multi-Mode Type] GT3A-1, -2, -3 Four Selectable Operation Modes in One Timer: ON Delay, Interval ON, Cycle, Cycle ON Flush Silhouette Control Units POWER Indicator (flashes during time delay period) OUT Indicator Display Lights Setting Knob Display Units Safety Products (2) Time Range Selector 1S, 10S, 10M, 10H Terminal Blocks (1) Operation Mode Selector A, B, C, D (3) Dial Selector 0-1, 0-3, 0-6, 0-18 Comm. Terminals Type List AS-Interface (1) Operation Mode Rated Voltage 100 to 240V AC 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC A: ON Delay B: Interval ON C: Cycle OFF D: Cycle ON Time Ranges 0.1 sec to 180 hours See Time Ranges for details. Time Ranges (3) Dial (2) Range 1S 10S 10M 10H Rated Load Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Maximum Switching Frequency Minimum Applicable Load External Protection Element Electrical Life Mechanical 240V AC/24V DC, 5A (resistive load) Contact Delayed SPDT Delayed SPDT + Instantaneous SPDT Delayed DPDT Type No. GT3A-1AF20 GT3A-2AF20 GT3A-2AD24 GT3A-3AF20 GT3A-3AD24 General Specifications 0-1 0-3 0-6 0 - 18 0.1 sec to 1 sec 0.1 sec to 10 sec 6 sec to 10 min 6 min to 10 hours 0.1 sec to 3 sec 0.3 sec to 30 sec 18 sec to 30 min 18 min to 30 hours 0.1 sec to 6 sec 0.6 sec to 60 sec 36 sec to 60 min 36 min to 60 hours 0.2 sec to 18 sec 1.8 sec to 180 sec 108 sec to 180 min 108 min to 180 hours Contact Ratings Type Output 240V AC, 3A 120V AC/30V DC, 5A (resistive load) GT3A-1, GT3A-2 240V AC, 3A (resistive load) 120V AC/30V DC, 5A (resistive load) AC: 960VA DC: 120W GT3A-3 240V AC/24V DC, 5A (resistive load) Type Operation System Operation Type Time Range Pollution Degree Overvoltage Category AF20 Rated Voltage AD24 AF20 Voltage Range AD24 Reset Voltage Operating Temperature Storage/Transportation Temperature Operating Humidity Altitude AC: 1200VA DC: 120W 250V AC/150V DC 5A 1800 operations/hour Reset Time Repeat Error Voltage Error Temperature Error Setting Error Insulation Resistance 5V DC, 10 mA (reference value) Dielectric Strength Fuse 250V, 5A 100,000 operations minimum (rated load) 20,000,000 operations minimum Vibration Resistance Shock Resistance Power Consumption (approx.) Degree of Protection AF20 Sockets Circuit Protectors GT3A-1 GT3A-2 GT3A-3 Solid-state CMOS circuitry Multi-Mode 0.1 sec to 180 hours 2 (IEC60664-1) III (IEC60664-1) 100 to 240V AC (50/60Hz) 24V AC (50/60Hz)/24V DC 85 to 264V AC (50/60Hz) 20.4 to 26.4V AC (50/60Hz)/21.6 to 26.4V DC Rated voltage × 10% minimum -10 to +50°C (no freezing) -30 to +70°C (no freezing) 2.9VA 2.5VA 2.2VA 200V AC 60Hz 4.7VA 4.3VA 4.0VA 1.3VA/0.5W 1.6VA/0.8W 40H × 36W × 72.2D mm 63g 73g Power Supplies PLCs & SmartRelay Operator Interfaces Sensors Control Stations 35 to 85% RH (no condensation) 0 to 2000m (operation) 0 to 3000m (transportation) 60 ms maximum ±0.2%, ±10 ms maximum (Note) ±0.2%, ±10 ms maximum (Note) ±0.2%, ±10 ms maximum (Note) ±10% maximum 100 MΩ minimum (500V DC megger) Between power and output terminals: 2000V AC, 1 minute Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole: 750V AC, 1 minute (GT3A-1, 2) 1000V AC, 1 minute (GT3A-3) 10 to 55 Hz, amplitude 0.75 mm, 2 hours each in 3 directions Operating extremes: 98 m/s2, Damage limits: 490 m/s2, 3 shocks each in 6 directions IP40 (timer), IP20 (socket) (IEC60529) 100V AC 60Hz AD24 (AC/DC) Dimensions Weight (approx.) Relays & Timers Explosion Protection References 1.8VA/0.7W 79g Note: The largest value becomes the error against a preset value depending on the time range. 1067 IDEC1066-1085.indd 1067 07.8.17 4:09:56 PM GT3 Series [Multi-Mode Type] Operation Chart Type No. Contact GT3A-1 Delayed SPDT Internal Connection 6 Operation Mode Selection 5 8 Operation Chart GT3A-2 Delayed SPDT + Instantaneous SPDT 7(~)/(+) 3 4 6 2(~)/(-) 1 8 GT3A-3 Delayed DPDT 7(~)/(+) 3 4 6 2(~)/(-) 1 8 5 5 7(~)/(+) 2(~)/(-) On Delay Item MODE A Set timer for desired delay, apply power to coil. Contacts transfer after preset time has elapsed, and remain in transferred position until timer is reset. Reset occurs with removal of power. Power TTerminal erminal No. Operation Set Time 2-7 Item Power Terminal No. 2-7 Operation Set Time Terminal No. Power 2-7 4-1 POWER POWER Instan- (NC) taneous Contact 3-1 Indicator OUT Operation Set Time 5-8,4-1 Delayed (NC) Contact 6-8,3-1 (NO) 5-8 Delayed (NC) Contact 6-8 (NO) 5-8 Delayed (NC) Contact 6-8 (NO) Item Indicator OUT (NO) POWER Indicator OUT Interval ON Item MODE B Set timer for desired delay, apply power to coil. Contacts transfer immediately, and return to original position after preset time has elapsed. Reset occurs with removal of power. Power Terminal No. 2-7 Operation Item Terminal No. Set Time Power 5-8 Delayed (NC) Contact 6-8 (NO) Operation POWER Instantaneous Contact OUT Terminal No. Operation Set Time Power 2-7 2-7 5-8,4-1 Delayed (NC) Contact 6-8,3-1 (NO) 5-8 Delayed (NC) Contact 6-8 (NO) Indicator Item Set Time 4-1 (NC) POWER Indicator 3-1 (NO) OUT POWER Indicator OUT Cycle OFF (OFF start) Item Terminal No. Operation MODE C Power Power 2-7 Cycle ON (ON start) Instantaneous Contact Indicator OUT D Item Terminal No. 2-7 Power 2-7 Operation Set Time 5-8,4-1 Delayed (NC) Contact 6-8,3-1 (NO) 4-1 (NC) POWER Indicator 3-1 (NO) OUT POWER OUT Item Terminal No. Power 2-7 5-8 Delayed (NC) Contact 6-8 (NO) POWER Functions in same manner as Mode C, with the exception that first transfer of contacts occurs as soon as power is applied. The ratio is 1:1. Time Off = Time On Operation Indicator Operation Item Indicator OUT Terminal No. Operation Item Terminal No. Power 2-7 Set Time Set Time MODE Terminal No. 5-8 Delayed (NC) Contact 6-8 (NO) 5-8 Delayed (NC) Contact 6-8 (NO) POWER Set timer for desired delay, apply power to coil. First transfer of contacts occurs after preset delay has elapsed, after the next elapse of preset delay contacts return to original position. The timer now cycles between on and off as long as power is applied. The ratio is 1:1. Time Off = Time On Item Set Time Set Time Power 2-7 5-8 Delayed (NC) Contact 6-8 (NO) Instantaneous Contact 5-8,4-1 Delayed (NC) Contact 6-8,3-1 (NO) 4-1 (NC) 3-1 (NO) Operation Set Time POWER Indicator OUT POWER Indicator OUT 1068 IDEC1066-1085.indd 1068 07.8.17 4:09:57 PM GT3 Series [Multi-Mode Type with Inputs (11 Pins)] GT3A-4, -5, -6 Four Selectable Operation Modes with Start, Gate, and Reset Inputs for External Control Control Units POWER Indicator (flashes during time delay period) LED OUT Indicator Flush Silhouette Display Lights Setting Knob Display Units (2) Time Range Selector 1S, 10S, 10M, 10H Safety Products Terminal Blocks (1) Operation Mode Selector A, B, C, D (3) Dial Selector 0-1, 0-3, 0-6, 0-18 Comm. Terminals Type List (1) Operation Mode A: ON Delay C: Signal ON Delay B: Cycle OFF D: Signal OFF Delay A: Interval ON C: Signal ON/OFF Delay A: One-Shot C: One-Shot Rated Voltage Code B: One-Shot Cycle, D: Signal OFF Delay B: One-Shot ON Delay D: Signal ON/OFF Delay (3) Dial 10M 10H GT3A-4AF20 100 to 240V AC 24V AC/24V DC 240V AC, 5A 24V DC, 5A (resistive load) Delayed DPDT Start Reset Gate 24V AC/24V DC GT3A-6AD24 0 - 18 0.1 sec to 1 sec 0.1 sec to 10 sec 6 sec to 10 min 6 min to 10 hours 0.1 sec to 3 sec 0.3 sec to 30 sec 18 sec to 30 min 18 min to 30 hours 0.1 sec to 6 sec 0.6 sec to 60 sec 36 sec to 60 min 36 min to 60 hours 0.2 sec to 18 sec 1.8 sec to 180 sec 108 sec to 180 min 108 min to 180 hours Electrical Mechanical 240V AC/24V DC, 5A (resistive load) AC: 1200VA DC: 120W 250V AC/150V DC 5A 1800 operations/hour 5V DC, 10 mA (reference value) Fuse 250V, 5A 100,000 operations minimum (rated load) 20,000,000 operations minimum Altitude Reset Time Repeat Error Voltage Error Temperature Error Setting Error Insulation Resistance Dielectric Strength Input Specifications The start input initiates delayed operation and controls output status. When the reset input goes on (L level), the timer is reset to the original time (time at power-on). The time delay operation is suspended while the gate input is on (L level). Operation System Operation Type Time Range Pollution Degree Overvoltage Category AF20 Rated Voltage AD24 AF20 Voltage Range AD24 Reset Voltage Operating Temperature Storage/Transportation Temperature Operating Humidity No-voltage contact inputs and NPN open collector transistor inputs are applicable. 24V DC, 1 mA maximum Input response time: 50 ms maximum Vibration Resistance Shock Resistance Degree of Protection Power Consumption (Approx.) Dimensions Weight (approx.) AF20 AD24 Relays & Timers GT3A-5AF20 GT3A-5AD24 GT3A-6AF20 0-6 Maximum Switching Voltage Maximum Switching Current Maximum Switching Frequency Minimum Applicable Load External Protection Element Gate Input 0.1 sec to 180 hours See Time Ranges for details 100 to 240V AC 0-3 Maximum Switching Power Reset Input AS-Interface Type No. GT3A-4AD24 0-1 Rated Load Start Input Input 24V AC/24V DC Contact Ratings Life Contact General Specifications (2) Range 10S Output 100 to 240V AC Time Ranges 1S Time Ranges Solid-state CMOS circuitry Multi-mode with inputs (11 pins) 0.1 sec to 180 hours 2 (IEC60664-1) III (IEC60664-1) 100 to 240V AC (50/60Hz) 24V AC (50/60Hz)/24V DC 85 to 264V AC (50/60Hz) 20.4 to 26.4V AC (50/60Hz)/21.6 to 26.4V DC Rated voltage × 10% minimum -10 to +50°C (no freezing) -30 to +70°C (no freezing) 35 to 85% RH (no condensation) 0 to 2000m (operation) 0 to 3000m (transportation) 60 ms maximum ±0.2%, ±10 ms (Note) ±0.2%, ±10 ms (Note) ±0.2%, ±10 ms (Note) ±10% maximum 100MΩ minimum (500V DC megger) Between power and output terminals: 2000V AC, 1 minute Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole: 1000V AC, 1 minute 10 to 55 Hz, amplitude 0.75 mm, 2 hours each in 3 directions Operating extremes: 98 m/s2 Damage limits: 490 m/s2 3 shocks each in 6 directions IP40 (timer), IP20 (socket) (IEC60529) Sockets Circuit Protectors Power Supplies PLCs & SmartRelay Operator Interfaces Sensors Control Stations Explosion Protection References 2.2VA (100V AC/60Hz), 4.1VA (200V AC/60Hz) 1.8VA (AC)/0.7W (DC) 40H × 36W × 72.2D mm 80g Note: The largest value becomes the error against a preset value depending on the time range. 1069 IDEC1066-1085.indd 1069 07.8.17 4:10:00 PM GT3 Series [Multi-Mode Type with Inputs (11 Pins)] Operation Chart • GT3A-4 Note: While the gate input is on during time delay operation, the POWER indicator flashing slows down. Operation Chart Delayed DPDT Contact 3 4 9 8 (~)/(+) 10 Internal Connection Operation Mode Selection 11 1 On Delay Item A Power Input MODE 6-2 ON or L 7-2 ON or L 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) Note: While the gate input is on during time-delay operation, the POWER indicator flashing slows down. (NO) POWER Indicator OUT Cycle Item Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts transfer after preset time has elapsed and remain in transferred position until preset time elapses a second time. The timer will now continue to cycle in above manner until reset applied. Power Input B T Start 6-2 ON or L 7-2 ON or L Gate 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) OUT Item Input Power Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts immediately transfer. When start input is removed time delay starts. After preset time contacts transfer back to original position. Timer is reset by initiation of reset input. T T T T T T Ta T Terminal No. T T T' T" T T T T T Operation 2-10 Start 6-2 ON or L 7-2 ON or L 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT Set Time Item Power Input D T Reset Delayed Contact Signal OFF Delay MODE Operation Indicator Gate For this mode a maintained pushbutton is required for start input. Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts will transfer immediately. After preset time (with start input still present) contacts will transfer back to original position. Remove start signal, at this time contacts will again transfer. Contacts will transfer to original position after preset time. Timer is reset by initiation of reset input. T" POWER Signal ON/OFF Delay C T' Terminal No. Reset Delayed Contact Ta 2-10 Set Time MODE 2(~)/(-) Operation Set Time MODE Gate Note: T = Set time Ta = Shorter than set time T = T’ + T’’ Terminal No. Start Delayed Contact Start 2-10 Reset Gate Power is applied to timer at all times. Set time for desired delay. When start input is supplied time delay starts, contacts transfer after preset time has elapsed. Contacts remain in transferred position until timer is reset. Reset 7 6 5 T Ta T Terminal No. Ta Ta T T' T" Ta Operation 2-10 Start 6-2 ON or L Reset 7-2 ON or L Gate 5-2 ON or L Delayed Contact T 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT Set Time T Ta Ta T T' T" 1070 IDEC1066-1085.indd 1070 07.8.17 4:10:02 PM GT3 Series [Multi-Mode Type with Inputs (11 Pins)] • GT3A-5 Flush Silhouette Operation Chart Delayed DPDT Contact 3 4 9 8 (~)/(+) 10 Internal Connection 7 6 5 Operation Mode Selection 11 1 Interval ON Item A Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts immediately transfer. After preset delay contacts return to original position. Timer is reset by initiation of reset input. Power Input MODE 6-2 ON or L Reset 7-2 ON or L Gate 5-2 ON or L Item Input Power 4-1 8-11 3-1 9-11 Safety Products Terminal Blocks (NC) Comm. Terminals (NO) AS-Interface Relays & Timers Operation Sockets Reset 7-2 ON or L Circuit Protectors 5-2 ON or L 4-1 8-11 3-1 9-11 Power Supplies (NC) (NO) PLCs & SmartRelay OUT Set Time Item Power T T Ta Terminal No. 6-2 ON or L Reset 7-2 ON or L Delayed Contact T T' T" Operator Interfaces T Operation Sensors 2-10 Start Control Stations 5-2 ON or L 4-1 8-11 3-1 9-11 Explosion Protection (NC) (NO) References POWER Indicator OUT Set Time Item Power T Ta T Terminal No. 6-2 ON or L Reset 7-2 ON or L Delayed Contact T Ta Ta T T' T" Ta Operation 2-10 Start Gate Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts immediately transfer. When start input is removed time delay starts. After preset time contacts transfer back to original position. Timer is reset by initiation of reset input. Terminal No. T" Indicator Input D T' POWER Signal OFF Delay MODE Ta 2-10 6-2 ON or L Gate For this mode a maintained pushbutton is required for start input. Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts will transfer immediately. After preset time (with start input still present) contacts will transfer back to original position. Remove start signal, at this time contacts will again transfer. Contacts will transfer to original position after preset time. Timer is reset by initiation of reset input. T Start Delayed Contact Input C Display Units Operation OUT Signal ON/OFF Delay MODE 2(~)/(-) POWER Gate Power is applied to timer at all times. Set timer for desired delay, initiate start input. After preset time has elapsed contacts will transfer. Contacts will transfer to their original position after preset time elapses a second time. Timer is reset by initiation of reset input. Display Lights Indicator One-Shot Cycle B Gate 2-10 Start Delayed Contact Control Units Note: T = Set time Ta = Shorter than set time T = T’ + T’’ Start Terminal No. Set Time MODE Reset 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT Set Time T Ta Ta T T' T" 1071 IDEC1066-1085.indd 1071 07.8.17 4:10:03 PM GT3 Series [Multi-Mode Type with Inputs (11 Pins)] • GT3A-6 Operation Chart Delayed DPDT Contact 3 4 9 (~)/(+) 10 8 Internal Connection Operation Mode Selection 11 1 One Shot Item A Power Input MODE 6-2 ON or L 7-2 ON or L 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT One Shot ON Delay Item Power Input B 7-2 ON or L T" 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) Indicator OUT Set Time Input Power T T Ta T Terminal No. T' T" Operation 2-10 Start 6-2 ON or L Reset 7-2 ON or L Delayed Contact 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT Signal ON/OFF Delay Item Power Input D T T Terminal No. 6-2 ON or L Reset 7-2 ON or L Delayed Contact Ta T' T" Operation 2-10 Start Gate For this mode a maintained pushbutton is required for start input. Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts will transfer immediately. After preset time (with start input still present) contacts will transfer back to original position. Remove start signal, at this time contacts will again transfer. Contacts will transfer to original position after preset time. Timer is reset by initiation of reset input. T' Operation Set Time MODE Ta POWER Gate Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts immediately transfer. After preset time has elapsed contacts transfer back to original position. Reset occurs with initiation of reset input. T Terminal No. Reset Item C Ta 2-10 6-2 ON or L Delayed Contact One Shot MODE Ta Start Gate Set timer for desired delay. When power is applied preset time begins and contacts transfer after preset time has elapsed (no start input needed at this time). Start input is now supplied, this causes the contacts to transfer back to original position. Contacts will remain in this position for preset time, after which they will transfer again. Contacts will now remain in this position until: reset, start input is applied again or power is removed. 2(~)/(-) Operation Set Time MODE Gate Terminal No. Start Delayed Contact Note: T = Set time Ta = Shorter than set time T = T’ + T’’ Start 2-10 Reset Gate Power is applied to timer at all times. Set timer for desired delay, initiate start input. Contacts immediately transfer. After preset time has elapsed contacts transfer back to original position. Reset occurs with initiation of reset input. Reset 7 6 5 5-2 ON or L 4-1 8-11 3-1 9-11 (NC) (NO) POWER Indicator OUT Set Time T T Ta T' T" Ta Ta T 1072 IDEC1066-1085.indd 1072 07.8.17 4:10:04 PM GT3 Series [Power OFF Delay Type] GT3F-1/GT3F-2 Specifically designed type for Power OFF Delay. Reset Inputs are available. Flush Silhouette Control Units GT3F-1 GT3F-2 POWER Indicator Display Lights Setting Knob Display Units Safety Products Terminal Blocks (1) Dial Selector 0-1, 0-3, 0-18, 0-60 Comm. Terminals (2) Time Range Selector 1s, 10s AS-Interface Type List (1) Operation Mode Rated Voltage Code 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC Power OFF Delay Time Ranges (3) Dial 0-1 0-3 0 - 18 0 - 60 0.1 sec to 1 sec 0.1 sec to 10 sec 0.1 sec to 3 sec 0.3 sec to 30 sec 0.2 sec to 18 sec 1.8 sec to 180 sec 0.6 sec to 60 sec 6 sec to 600 sec (2) Range Timeout Repeat Cycle Reset Input Repeat Cycle 3 sec minimum 3 sec minimum Contact Ratings Type Rated Load Minimum Switching Power Minimum Switching Voltage Minimum Switching Current Maximum Switching Frequency Minimum Applicable Load External Protection Element Life Electrical Mechanical 250V AC /30V DC, 5A Delayed SPDT Reset 250V AC /30V DC, 3A Delayed DPDT Without GT3F-1 GT3F-2 250V AC/30V DC, 250V AC/30V DC, 5A (resistive load) 3A (resistive load) AC: 1250VA AC: 750VA DC: 150W DC: 90W 250V AC/125V DC 5A 3A 1800 operations/hour 5V DC, 10 mA 5V DC, 100 mA Fuse 250V, 5A Fuse 250V, 3A 100,000 operations minimum (rated load) 10,000,000 operations minimum Operation System Operation Type Time Range Pollution Degree Overvoltage Category AF20 Rated Voltage AD24 AF20 Voltage Range AD24 Time Delay Operation Start Voltage Minimum Power Application Time (Note 1) Operating Temperature Storage/Transportation Temperature Operating Humidity Altitude Repeat Error Voltage Error Temperature Error Setting Error Insulation Resistance Dielectric Strength Input Specifications Reset Input Input Type No. GT3F-1AF20 GT3F-1AD24 GT3F-2AF20 GT3F-2AD24 General Specifications • GT3F-1/GT3F-2 10S Contact 0.1 sec to 600 sec Time Ranges 1S Output The contact is reset by turning the reset input on (L level). No-voltage contact input and NPN open collector transistor input are applicable. 6V DC, 0.6 mA maximum Input Response Time (AC Type): ON: 50 ms maximum OFF: 1 sec maximum Vibration Resistance Shock Resistance Degree of Protection AF20 AD24 Dimensions Power Consumption (approx.) Weight (approx.) Relays & Timers Sockets Circuit Protectors Solid-state CMOS circuitry Power OFF delay 0.1 sec to 600 hours 2 (IEC60664-1) III (IEC60664-1) 100 to 240V AC (50/60Hz) 24V AC (50/60Hz)/24V DC 85 to 264V AC (50/60Hz) 20.4 to 26.4V AC (50/60Hz)/21.6 to 26.4V DC Power Supplies PLCs & SmartRelay Operator Interfaces Rated Voltage × 10% minimum Sensors 0.4 sec (time range: 180 sec or less) 1 sec (time range: 600 sec) -10 to +50°C (no freezing) Control Stations -30 to +70°C (no freezing) 35 to 85% RH (no condensation) 0 to 2000m (operation) 0 to 3000m (transportation) ±0.2%, ±10 ms (Note 2) ±0.2%, ±10 ms (Note 2) ±0.2%, ±10 ms (Note 2) ±10% maximum 100 MΩ min. (500V DC megger) Between power and output terminals: 2000V AC, 1 minute Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole: 1000V AC, 1 minute 10 to 55Hz, amplitude 0.75 mm, 2 hours each in 3 directions Operating extremes: 98 m/s2, Damage limits: 490 m/s2, 3 shocks each in 6 directions IP40 (timer), IP20 (socket) (IEC60529) 1.1 VA (100V AC/60Hz), 2.3 VA (200V AC/60Hz) 0.7 VA (AC)/0.2W (DC) 40H × 36W × 72.2D mm GT3F-1 GT3F-2 77g 79g Explosion Protection References Note 1: An inrush current flows during minimum power application time. AF20: Approx. 0.4A, AD24: Approx. 1.2A Note 2: The largest value becomes the error against a preset value depending on the time range. 1073 IDEC1066-1085.indd 1073 07.8.17 4:10:05 PM GT3 Series [Power OFF Delay Type] Operation Chart Contact Internal Connection GT3F-1 Operation Chart Item Delayed SPDT Output with Reset Input 6 5 Power 2-7 Reset Input 4-1 ON or L Delayed Contact (~)/(+) 7 4 Terminal No. Reset Indicator Operation 5-8 (NC) 6-8 (NO) POWER 1 Set Time 8 2 (~)/(-) Item Delayed DPDT Output Power 4 6 (~)/(+) 5 7 Delayed Contact Indicator 1 8 T Ta Ts T T = Set time Ta = Shorter than set time Ts = 1 sec Tr = Minimum power application time • 0.4 sec (time range: 180 sec or less) • 1 sec (time range: 600 sec or less) • When power turns on, the NO output contact goes on. When a preset time has elapsed after the power has been turned off, the NO output contact goes off. • The contact is reset by turning the reset input on. GT3F-2 3 Tr 2 (~)/(-) Terminal No. Operation 2-7 5-8, 4-1 (NC) 6-8, 3-1 (NO) POWER Set Time T Tr T T = Set time Tr = Minimum power application time • 0.4 sec (time range: 180 sec or less) • 1 sec (time range: 600 sec or less) • When power turns on, the NO output contact goes on. When a preset time has elapsed after the power has been turned off, the NO output contact goes off. 1074 IDEC1066-1085.indd 1074 07.8.17 4:10:07 PM GT3 Series [Star-Delta Type] GT3S-1/GT3S-2 Star-Delta Output Mode Flush Silhouette Control Units Star Output Indicator Delta Output Indicator Display Lights Star Setting Knob Display Units Safety Products (2) Star-Delta Switching Time Selector 0.05 sec, 0.1 sec, 0.25 sec, 0.5 sec Terminal Blocks (1) Star Dial Selector 0-5, 0-10, 0-50, 0-100 Comm. Terminals Type List AS-Interface (1) Operation Mode Star-Delta Rated Voltage 100 to 240V AC Time Range Star: 0.05 to 100 sec Star-Delta switching time 0.05 sec 0.10 sec 0.25 sec 0.50 sec Time Ranges 1 Star Dial Selector Dial 0 -- 5 0 -- 10 0 -- 50 0 -- 100 Time Range 0.05 sec -- 5 sec 0.1 sec -- 10 sec 0.5 sec -- 50 sec 1 sec -- 100 sec Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Maximum Switching Frequency Minimum Applicable Load External Protection Element Life Electrical Mechanical 250V AC/ 30V DC, 5A (resistive load) Contact Star: Delayed SPST-NO Delta: Delayed SPST-NO Star: Delayed SPST-NO Delta: Delayed SPST-NO Instantaneous SPST-NO Type No. GT3S-1AF20 250V AC/30V DC, 5A (resistive load) AC: 1250VA DC: 150W 265V AC/125V DC 5A 1800 operations/hour 5V DC, 100mA (reference value) Fuse 250V, 5A 100,000 operations minimum (rated load) 20,000,000 operations minimum Operation System Operation Type Time Range Pollution Degree Overvoltage Category Rated Voltage Voltage Range Reset Voltage Operating Temperature Storage/Transportation Temperature Operating Humidity Altitude Reset Time Repeat Error Voltage Error Temperature Error Setting Error Insulation Resistance Dielectric Strength Vibration Resistance Shock Resistance Degree of Protection Power Consumption (approx.) Dimensions Weight (approx.) Relays & Timers GT3S-2AF20 Sockets General Specifications 2 Star-Delta Switching Time Selector Indication Time 0.05 0.05 sec 0.1 0.1 sec 0.25 0.25 sec 0.5 0.5 sec Contact Ratings Rated Load Output Solid-state CMOS circuitry Star-delta Star side: 0.05 sec to 100 sec Star delta switching time: 0.05, 0.1, 0.25, 0.5 sec 2 (IEC60664-1) III (IEC60664-1) 100 to 240V AC (50/60Hz) 85 to 264V AC (50/60Hz) Rated Voltage × 10% minimum --10 to +50°C (no freezing) Circuit Protectors Power Supplies PLCs & SmartRelay Operator Interfaces --30 to +70°C (no freezing) Sensors 35 to 85% RH (no condensation) 0 to 2000m (operation) 0 to 3000m (transportation) 500 ms maximum ±0.2%, ±10 ms (Note) ±0.2%, ±30 ms (Note) ±0.2%, ±10 ms (Note) ±10% maximum 100 MΩ minimum (500V DC megger) Between power and output terminals: 2000V AC, 1 minute Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole: 1000V AC, 1 minute 10 to 55 Hz, amplitude 0.75 mm, 2 hours each in 3 directions Operating extremes: 98 m/s2, Damage limits: 490 m/s2, 3 shocks each in 6 directions IP40 (timer), IP20 (socket) (IEC60529) GT3S-1AF20 GT3S-2AF20 2.3VA 2.3VA (100V AC/60Hz) (100V AC/60Hz) 4.0VA 3.8VA (200V AC/60Hz) (200V AC/60Hz) 40H × 36W × 72.2D mm GT3S-1AF20 GT3S-2AF20 68g 75g Control Stations Explosion Protection References Note: The largest value becomes the error against a preset value depending on the time range. 1075 IDEC1066-1085.indd 1075 07.8.17 4:10:07 PM GT3 Series [Star-Delta Type] Operation Chart Contact GT3S-1 Star : Delayed SPST-NO Delta: Delayed SPST-NO Internal Connection (~) 5 7 6 Operation Chart Item Terminal No. Power 2-7 Star Delayed Contact Delta Delayed Contact 8-5 (NO) Operation 8-6 (NO) Star Indicator Delta 2 8 (~) Set Time T1 T2 T3 The star delayed contact goes on when power is turned on and goes off after a set time for the star contact (T1). The delta contact goes on after star-delta switching time (T2) and goes off when power is turned off. • T1 = Star ON time (Set Time), T2 = Star-delta swithing time, T3 = Star ON time GT3S-2 Star : Delayed SPST-NO Delta: Delayed SPST-NO Instantaneous SPST-NO (~) 3 5 6 7 Item Terminal No. Power 2-7 Star Delayed Contact Delta Delayed Contact 8-5 (NO) Instantaneous contact 3-1 (NO) Operation 8-6 (NO) Star Indicator Delta 1 8 2 (~) Set Time T1 T2 T3 • The star delayed contact goes on when power is turned on and goes off after a set time for the star contact (T1). The delta contact goes on after star-delta switching time (T2) and goes off when power is turned off. • Instantaneous contact goes on when power is turned on and goes off when power is turned off. • T1 = Star ON time (Set Time), T2 = Star-delta swithing time, T3 = Star ON time 1076 IDEC1066-1085.indd 1076 07.8.17 4:10:09 PM GT3 Series Multi-function Timers [Twin-Timer Type] GT3W-A11, -A13, -A31, A33 Multi-range Twin-Timer type with 8 operation modes Flush Silhouette Control Units OUT Indicators Display Lights POWER Indicator Setting Knob (T2) Display Units Time Range Selector Mode Selector Safety Products Setting Knob (T1) Terminal Blocks Comm. Terminals Type List (1) Operation Mode 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC 100 to 240V AC 24V AC/24V DC Sequential Start Coarse/Fine Adjustment Instantaneous Cycle Cycle Cycle Inversion Interval ON Interval ON Delay Sequential Interval Time Ranges 0.1 sec to 6 hours Time Range Time Scale Selector Range 0.1 sec to 1S 1 sec 0.3 sec to 10S 0-1 10 sec 15 sec to 10M 10 min 0.1 sec to 1S 6 sec 1.3 sec to 10S 60 sec 7.5 sec to 1M 0-6 1 min 75 sec to 10M 60 min 7.5 min to 1H 6 hours Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Maximum Switching Frequency Minimum Applicable Load External Protection Element Life Electrical Mechanical T1 Type No. T2 0.1 sec to 6 hours 0.1 sec to 6 hours 0.1 sec to 300 hours 0.1 sec to 6 hours 0.1 sec to 300 hours 0.1 sec to 300 hours GT3W-A11AF20N GT3W-A11AD24N GT3W-A13AF20N GT3W-A13AD24N GT3W-A31AF20N GT3W-A31AD24N GT3W-A33AF20N GT3W-A33AD24N General Specifications 0.1 sec to 300 hours Time Range Time Scale Selector Range 0.1 sec to 1S 3 sec 3.8 sec to 1M 0-3 3 min 3.8 min to 1H 3 hours 0.6 sec to 1S 30 sec 38 sec to 1M 30 min 38 min to 0 - 30 1H 30 hours 10H 6.3 hours to 300 hours Contact Ratings Rated Load AS-Interface Time Ranges Rated Voltage 240V AC, 3A (resistive load) 120V AC/ 30V DC, 5A (resistive load) AC: 960VA DC: 120W 250V AC/150V DC 5A 1800 operations/hour 5V DC, 10mA (reference value) Fuse 250V, 5A 100,000 operations minimum (rated load) 20,000,000 operations minimum Operation System Operation Type Time Range Pollution Degree Overvoltage Category AF20 Rated Range AD24 AF20 Voltage Range AD24 Reset Voltage Operating Temperature Storage/Transportation Temperature Operating Humidity Altitude Reset Time Repeat Error Voltage Error Temperature Error Setting Error Insulation Resistance Dielectric Strength Vibration Resistance Shock Resistance Degree of Protection Power Consumption (approx.) Dimensions Weight (approx.) AF20 AD24 Relays & Timers Sockets Circuit Protectors Power Supplies Solid-state CMOS circuitry Multi-Mode 0.1 sec to 300 hours 2 (IEC60664-1) III (IEC60664-1) 100 to 240V AC (50/60Hz) 24V AC (50/60Hz)/ 24V DC 85 to 264V AC (50/60Hz) 20.4 to 26.4V AC (50/60Hz)/21.6 to 26.4V DC Rated voltage × 10% minimum -10 to +50°C (no freezing) -30 to +70°C (no freezing) 35 to 85% RH (no condensation) 0 to 2000m (operation) 0 to 3000m (transportation) 60 ms maximum ±0.2%, ±10 ms (Note) ±0.2%, ±10 ms (Note) ±0.2%, ±10 ms (Note) ±10% maximum 100 MΩ minimum (500V DC megger) Between power and output terminals: 2000V AC, 1 minute Between contacts of different poles: 2000V AC, 1 minute Between contacts of the same pole: 750V AC, 1 minute 10 to 55Hz, amplitude 0.75 mm, 2 hours each in 3 directions Operating extremes: 98 m/s2 Damage limits: 490 m/s2 3 shocks each in 6 directions IP40 (timer), IP20 (socket) (IEC60529) PLCs & SmartRelay Operator Interfaces Sensors Control Stations Explosion Protection References 2.3VA (100V AC /60Hz) 4.6VA (200V AC /60Hz) 1.8VA (AC)/0.9W (DC) 40H × 36W × 70.0D mm 73g Note: The largest value becomes the error against a preset value depending on the time range. 1077 IDEC1066-1085.indd 1077 07.8.17 4:10:09 PM GT3 Series Multi-function Timers [Twin-Timer Type] Operation Chart Operation Chart Delayed SPDT + Delayed SPDT Contact Internal Connection Operation Mode Selection 3 4 6 1 8 5 7(~)/(+) Operation Mode Selection 2(~)/(-) Sequential Start A Operation Chart Delayed SPDT + Delayed SPDT Contact Internal Connection Item Terminal No. Power 2-7 Delayed Contact Ry1 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON after T1 E Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 ON after T1 + T2 OUT1 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON during T1 OFF during T2 ON during T1 OFF during T2 T1 Set Time T2 T1 T2 Interval ON Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON after T1 + T2 F Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 ON after T1 + T2 OUT1 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON during T1 ON after T1, during T2 OUT1 Indicator Indicator OUT2 OUT2 Set Time T1 Set Time T2 T1 T2 Interval ON Delay Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description Instantaneous ON G Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 OFF during T1 ON during T2 OUT1 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON during T1 ON after T1 + T2 OUT1 Indicator Indicator OUT2 Set Time OUT2 T1 Set Time T2 Cycle D 2(~)/(-) OUT2 Set Time C 8 7(~)/(+) Indicator OUT2 Instantaneous Cycle 1 5 OUT1 Indicator B 4 6 Cycle Inversion Delayed Contact Ry2 Coarse/ Fine Adjustment 3 T1 T2 Sequential Interval Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description OFF during T1 ON during T2 OFF during T1 ON during T2 H Item Terminal No. Power 2-7 Delayed Contact Ry1 Delayed Contact Ry2 OUT1 Operation 1-4 (NC) 1-3 (NO) 5-8 (NC) 6-8 (NO) Description ON during T1 + T2 ON after T1, during T2 OUT1 Indicator Indicator OUT2 Set Time OUT2 T1 T2 Set Time T1 T2 1078 IDEC1066-1085.indd 1078 07.8.17 4:10:11 PM GT3 Series Multi-function Timers [Accessories] Applicable Sockets & Hold-Down Springs (Optional) Flush Silhouette • DIN Rail Mount Socket Item 8-Pin Screw Terminal Socket 11-Pin Screw Terminal Type No. SR2P-05A SR2P-06A SR2P-05C SR3P-05A SR3P-06A SR3P-05C Ordering Type No. SR2P-05A SR2P-06A SR2P-05C SR3P-05A SR3P-06A SR3P-05C Package Quantity 1 1 1 1 1 1 SFA-202 SFA-202PN20 10 sets (20 pcs) SFA-203 SFA-203PN20 10 sets (20 pcs) Hold-Down Spring Remarks Control Units Finger-safe type Display Lights Finger-safe type For SR2P-06A/SR3P-06A (2 pcs/set) For SR3P-05A (2 pcs/set) Display Units Safety Products Note: All are UL recognized, CSA certified, and TÜV approved. SR2P-06A SR3P-05A SR3P-06A SFA-202 (2 pcs/set) Terminal Blocks SFA-203 (2 pcs/set) Comm. Terminals AS-Interface • Panel Mount Socket Item Socket Type No. Ordering Type No. Package Quantity 8-Pin Solder Terminal SR2P-511 SR2P-511 1 11-Pin Solder Terminal SR3P-511 SR3P-511 1 SFA-402 SFA-402PN10 10 Hold-Down Spring Remarks Relays & Timers Sockets For SR2P-511/SR3P-511 Note: SR2P-511 and SR3P-511 are UL recognized and CSA certified. SR2P-511 SR3P-511 Circuit Protectors SFA-402 Power Supplies PLCs & SmartRelay • Panel Mount Adapter and wiring Socket Adapter (8-pin Wiring Socket Adapter) SR6P-S08 Package Quantity: 1 Item DIN 48mm Square Panel Mount Adapter Wiring Socket Adapter Type No. Color: Gray RTB-G01 Color: Beige RTB-M01 Color: Black RTB-B01 8-Pin Solder Terminal 8-Pin Screw Terminal 11-Pin Solder Terminal 11-Pin Screw Terminal (11-pin Wiring Socket Adapter) SR6P-S11 Operator Interfaces Sensors Control Stations (8-pin Screw Wiring Socket Adapter) SR6P-M08G SR6P-S08 SR6P-M08G SR6P-S11 SR6P-M11G (11-pin Screw Wiring Socket Adapter) SR6P-M11G Explosion Protection References • Finger-safe 11-pin screw wiring socket adapter (Type No.: SR6P-C11) is also available. • Installation of Hold-Down Springs (DIN Rail Mount Socket) Insert the springs into the outer slots with the projections facing inside. (Panel Mount Socket) Hold-Down Spring Insert the springs into the slots. SFA-402 Insert 8-Pin Socket Socket SR2P-06A Hold-Down Spring (optional) SFA-202 (2 pcs/set) Socket Hold-Down Spring (optional) SR3P-05A SFA-203 (2 pcs/set) SR2P-511 SR2P-70 Note: Once installed into the socket, the hold-down springs cannot be removed. 1079 IDEC1066-1085.indd 1079 07.8.17 4:10:12 PM GT3 Series Multi-function Timers [All] • GT3A-4, -5, -6 (11-pin) (SR3P-05A Socket) Dimensions When Using DIN Rail Mount Socket (SR2P-06A Socket) • GT3A-1, -2, -3/GT3F/GT3S (8-pin) (When using DIN rail) BAA, BAP: 105.5 max. DIN Rail (BAA, BAP, BADA) 95 max. (Note 2) 52 40 33 (When using DIN rail) BAA, BAP: 99 max. (Note 1) ø27 101.5 max. Hold-Down Spring 36 40 60 1.7 Hold-Down Spring (SFA-202) 36 8 64.2 13 DIN Rail 1 18 8 64.2 16.5 20 13 28.5 (SR3P-05C Socket) (When using DIN rail) BAA, BAP: 105 max. 22 DIN Rail (BAA, BAP) 103.5 max. 40 Note 1: For SR2P-05A: 105.5 max. For SR2P-05C: 107 max. Note 2: For SR2P-05A: 101.5 max. For SR2P-05C: 103 max. 21.5 • GT3W 36 8 64.2 13 (SR3P-06A Socket) (When using DIN rail) BAA, BAP: 99 max. 31.7 95 max. 60 1.7 40 1 22 Hold-Down Spring (SFA-202) 36 Note 3: For SR2P-05A: 103.1 max For SR2P-05C: 104.6 max. Note 4: For SR2P-05A: 99.1 max. For SR2P-05C: 100.6 max. 22 7(~)/(+) Hold-Down Spring (SFA-402) 6 4.2 2-ø3.5 Mounting Hole (or M3 Tapped Hole) (Terminal Arrangement) 11 1 3 Reset 7 6 5 4 9 34 (~)/(+) 8 10 Gate 11 1 2(~)/(-) 2.5 • GT3A-4, -5, -6 (SR3P-511 Socket) Gate Hold-Down Spring (SFA-402) 4.2 4 9 8 (~)/(+) 10 7 6 5 11 1 6 Reset 4 Start 8 8 5 6 7 4 3 2 34 2.5 10 11 8 9 1 11 10 (BOTTOM VIEW) 8 1 2 (~)/(-) 2 (~)/(-) All dimensions in mm. GT3W (~) 7 3 2 1 (~) (~)/(+) 7 Reset GT3S-2 6 5 2.5 (~) 5 4 6 1 Gate 2(~)/(-) GT3S-1 3 7 5 2-ø3.5 Mounting Hole (or M3 Tapped Hole) (Terminal Arrangement) 38 (~)/(+) 3 6 GT3F-2 50 GT3A-6 (BOTTOM VIEW) Reset Start 2(~)/(-) GT3F-1 10 11 2.5 7 6 5 Start 6 7 1 8 GT3A-5 (~)/(+) 8 10 4 9 3 2 38 3 2(~)/(-) Panel Surface GT3A-4 8 1 2(~)/(-) 38 8 1 2(~)/(-) 50 4 5 8 38 5 0 4 6 3 7(~)/(+) ø3 GT3A-3 5 13 When Using Panel Mount Socket • GT3A-1, -2, -3/GT3F/GT3S/GT3W (8-pin) (SR2P-511 Socket) Panel Surface 7(~)/(+) 4 6 64.2 • Calculate the dimensions for mounting, referring to the diagrams on pages 1109 and 1100 for SR2P-05U, SR2P-05C, and SR3P-05C. [Internal Connections] GT3A-1 GT3A-2 3 8 DIN Rail 18 1 13 0 64.2 5.6 ø3 36 DIN Rail 18 31.7 60 1.7 40 Hold-Down Spring (SFA-202) 5 30 ( g ) BAA, BAP: 96.6 max. (Note 3) 92.6 max. (Note 4) 6 3 31.7 (SFA-203) 5 6 8 7 3 4 6 2 1 8 5 7(~)/(+) 2(~)/(-) (~) 1080 IDEC1066-1085.indd 1080 07.8.17 4:10:13 PM GT3 Series Multi-function Timers [All] • All GT3 Series When using DIN 48mm-square Panel Mount Adapter (For 8-pin solder wiring socket adapter: SR6P-S08 and 11-pin solder wiring socket adapter: SR6P-S11) 98 max. (Mounting Hole Layout) 1.7 48 11 Single Mounting Display Units Wiring Socket Adapter 61.2 (8-pin Screw Terminal Wiring Socket Adapter: SR6P-M08G) Horizontal Close Mounting 48N--3 Safety Products 8-M3.5 Terminal Screw Panel Thickness: 0.8 to 5 mm Tolerance: +0.5 to 0 N: No. of timers mounted 44.6 3.5 max. 3 4 5 6 2 1 8 7 Terminal Blocks 5.6 min. ø3.6 min. 30.4 44.6 Control Units Display Lights 45 45 48 42.5 45 Panel Thickness: 0.8 to 5 mm Flush Silhouette 6.9 max. Comm. Terminals 7 9.8×3 80.5 AS-Interface (11-pin Screw Terminal Wiring Socket Adapter: SR6P-M11G) Relays & Timers 11-M3.5 Terminal Screw 45 16.7 Sockets 3.5 max. 11 7 1 2 6 ø3.6 min. 45 34 5 Circuit Protectors 6.9 max. 4 30.5 5.8 min. 3 8 9 10 7 Power Supplies 8.5×4 92 (Finger-safe 11-pin Screw Terminal Wiring Socket Adapter: SR6P-C11) PLCs & SmartRelay 11-M3.5 Terminal Screw 45 16.7 2 1 11 7 Operator Interfaces 6 45 34 A1 15 25 Finger-safe structure complies with VDE 0106 T.100. 5 16 18 26 28 A2 4 33.5 95 3 8 9 7 Sensors 10 Control Stations 1.5 8.5×4 All dimensions in mm. Explosion Protection References 1081 IDEC1066-1085.indd 1081 07.8.17 4:10:15 PM GT3 Series Multi-function Timers [Safety Precautions and Instructions] Safety Precautions ! • Be sure to turn off power before mounting, removal, wiring, maintenance and inspection. Otherwise, electric shock or fire may occur. • Be sure to use timers within rated specification values. Otherwise electric shock or fire may occur. • Be sure to use wires to meet voltage and current requirements and tighten M3.5 terminal screws to a torque of 1.0 to 1.3 N•m. Be sure to solder the terminals correctly. Loose terminal screws or incomplete soldering may cause abnormal heat and fire. Instructions Mode Setting Time Range Setting GT3A only The time range is calibrated at its maximum time scale, therefore, it is desirable to use the timer at a setting as close to its maximum time scale as possible for accurate time delay. For a more accurate time delay, adjust the setting knob by measuring the operating time before application. The operation mode can be selected from A, B, C, and D modes using the Operation Mode Selector. The operation mode is changed from A to B, C, and D in turn by turning the Operation Mode Selector clockwise using a flat screwdriver 4 mm wide maximum and the selected mode is displayed in the window. Since this selector does not turn infinitely, turn the selector clockwise when Mode A is displayed and counterclockwise when Mode D is displayed. Setting Knob Time Range Selector Operation Mode Selector Dial Selector 1. GT3A (Multi-Mode Analog Setting Type) Time range can be selected from 1S, 10S, 10M, and 10H by turning the Time Range Selector with a flat screwdriver 4 mm wide maximum. The four different ranges of 0 to 1, 0 to 3, 0 to 6, and 0 to 18 are displayed in the six windows by turning the Dial Selector, allowing for selecting the best suited scale. Since the selectors do not turn infinitely, turn the selectors clockwise when 1S or 0-1 is displayed and counterclockwise when 10H or 0-18 is displayed. • Time Range Determined by Time Range Selector and Dial Selector Dial Selector Time Range 1S • Mode Code and Operation Mode Type No. MODE Code GT3A-1, -2, -3 GT3A-4 A ON Delay ON Delay B Interval ON Cycle C Cycle D Cycle ON Signal ON/ OFF Delay Signal OFF Delay 10S GT3A-5 GT3A-6 Interval ON One-Shot One Shot Cycle Signal ON/ OFF Delay Signal OFF Delay One-Shot ON Delay One-Shot Signal ON/ OFF Delay 10M 10H 0-1 0-3 0-6 0 - 18 0.1 sec to 1 sec 0.1 sec to 10 sec 6 sec to 10 min 6 min to 10 hours 0.1 sec to 3 sec 0.3 sec to 30 sec 18 sec to 30 min 18 min to 30 hours 0.1 sec to 6 sec 0.6 sec to 60 sec 36 sec to 60 min 36 min to 60 hours 0.2 sec to 18 sec 1.8 sec to 180 sec 108 sec to 180 min 108 min to 180 hours The set time is selected by turning the setting knob. [Setting Examples] • When the setting knob is set at 1.5, with dial 0-3 and time range 10S selected, then the set time is 15 sec (1.5 × 10S). • When the setting knob is set at 0.2, with dial 0-1 and time range 10H selected, then the set time is 2 hours (0.2 × 10H). 2. GT3F (OFF Delay Type) The time range of GT3F-1 and GT3F-2 can be selected between 1S and 10S with the Time Range Selector by using a flat screw driver. The selected time range (0-1, 0-3, 0-18, or 0-60) is displayed in the six windows of the Setting Knob by turning Dial Selector which allows to set the scale. Note that the switches do not turn infinitely. • Time Range Determined by Time Range Selector and Dial Selector (1) Dial (2) Range 1S 10S 0-1 0-3 0 - 18 0 - 60 0.1 sec to 1 sec 0.1 sec to 10 sec 0.1 sec to 3 sec 0.3 sec to 30 sec 0.2 sec to 18 sec 1.8 sec to 180 sec 0.6 sec to 60 sec 6 sec to 600 sec The set time is selected by turning the Setting Knob. [Setting Examples] • When the setting knob is set at 2.5, with dial 0-3 and range 1S selected, then the set time is 2.5 sec (2.5 × 1S). • When the setting knob is set at 15, with dial 0-18 and range 10S selected, then the set time is 150 sec (15 × 10S). 1082 IDEC1066-1085.indd 1082 07.8.17 4:10:16 PM GT3 Series Multi-function Timers [Instructions] 3. GT3S (Star-Delta Type) Flush Silhouette Control Units Setting Knob Display Lights Star-Delta Switching Time Selector Display Units Star Dial Selector The scale range on the star side can be selected from four different ranges of 0 to 5, 0 to 10, 0 to 50, and 0 to 100 displayed in the six windows by turning the Star Dial Selector. Note that the selectors does not turn infinitely. • Time Range Determined by Time Range Selector and Dial Selector Star Dial Selector Dial 0 -- 5 0 -- 10 0 -- 50 0 -- 100 Time Range 0.05 sec -- 5 sec 0.1 sec -- 10 sec 0.3 sec -- 50 sec 1 sec -- 100 sec Star-Delta Switching Time Selector Indication Time 0.05 0.05 sec 0.1 0.1 sec 0.25 0.25 sec 0.5 0.5 sec The Star ON time is selected by turning the Setting Knob. [Setting Examples] • If the setting knob is set at 8, with Star Dial Selector 0-10 and StarDelta switching time 0.1S selected, the Star ON time (T1) is 8 sec and the Star-Delta switching time (T2) is 0.1 sec. Safety Products Selector Setting • Use a flat screwdriver with a diameter of 4 mm maximum to turn the selector. Turn the selector until it clicks. Otherwise, malfunction may occur. Also, do not rotate the selector forcibly since the selector does not turn infinitely. • Since changing the setting during operation may cause malfunction, turn power off before changing the setting. Power Terminal Blocks Comm. Terminals AS-Interface • Since DC types have a polarity in their power supply connection, connect the power according to wiring diagram. • Since AC type GT3A, GT3S, and GT3W comprise a capacitive load, the SSR dielectric strength should be two or more times as large as the power voltage when switching the timer power using an SSR. • Storage temperature should range from -25°C to +80°C. If the product has been stored at a temperature below -10°C, leave the product at room temperatures for more than 3 hours before using. • Do not remove the housing. Relays & Timers Sockets Circuit Protectors Power Supplies 4. GT3W [Twin-Timer Type] Use a flat screwdriver with a diameter of 4 mm maximum to turn Time Range Selector and gain time range as shown in the table below. Note that the selectors do not turn infinitely. PLCs & SmartRelay Operator Interfaces • Time Range Determined by Time Range Selector and Dial Selector 0.1 sec to 6 hours Time Range Scale Time Range Selector 0.1 sec to 1S 1 sec 0.3 sec to 0-1 10S 10 sec 15 sec to 10M 10 min 0.1 sec to 1S 6 sec 1.3 sec to 10S 60 sec 7.5 sec to 1M 0-6 1 min 75 sec to 10M 60 min 7.5 min to 1H 6 hours 0.1 sec to 300 hours Time Range Scale Time Range Selector 0.1 sec to 1S 3 sec 3.8 sec to 0-3 1M 3 min 3.8 min to 1H 3 hours 0.6 sec to 1S 30 sec 38 sec to 1M 30 min 38 min to 0 - 30 1H 30 hours 10H Sensors Control Stations Explosion Protection References 6.3 hours to 300 hours Note: No blank time range can be set. 1083 IDEC1066-1085.indd 1083 07.8.17 4:10:17 PM GT3 Series Multi-function Timers [Instructions] To avoid electric shock, do not touch the input signal terminal during power voltage application. • When connecting the input signal terminals of two or more GT3A timers to the same contact or transistor, the input terminals of the same number should be connected. (Connect Terminals No. 2 in common.) • Never apply the input signals to two or more GT3F timers using the same contact or transistor. [Incorrect] GT3 Series Timer Input Contact or Transistor Gate Input Inputs of GT3A and GT3F Start Input The GT3F, consisting of a high-impedance circuit, may not be reset due to the influence of an inductive voltage or residual voltage caused by a leakage current. In not reset, connect an RC filter or bleeder resistor between power terminals so that the voltage between power terminals can be reduced to less than 15% of the rated voltage. • For transistor input, use transistors with following specifications; VCE = 40V, VCES = 1V or less, IC = 50mA or more, ICBO = 50μA or less. The resistance should be less than 1kΩ when the transistor is on. When the output transistor switches on, a signal is inputted to the timer. Reset Input Wiring 6 5 7 4 8 3 9 2 10 1 11 Power GT3A Transistor output equipment such as proximity switches and photoelectric switches can input signals if they are voltage/current output type, power voltage ranges from 18 to 30V, and residual voltage is 1V. When the signal voltage switches from H to L, a signal is inputted to the timer. Transistor Output Circuit Input Terminal 2 10 Power Input Terminal 2 Transistor 10 5, 6, 7 Input Terminal 2 [correct] Input Terminal 2 10 Power 2 10 • In a transistor circuit for controlling input signals with its primary and secondary power circuits isolated, do not ground the secondary circuit. GT3 Series Timer Power Repeat Error Rectifier Circuit =± • Do not connect input signal terminals of the GT3A timer to other terminals than No. 2. Never apply voltage to input signal terminals. Otherwise, the internal circuit may be damaged. 2 If the power application time to the GT3F is shorter than the minimum power application time, the output relay may not operate or the timer may operate faster than the preset time. This indicates variance of operation time when operation is repeated under the same conditions. The variance is calculated from the following formula and the measurements should be done 5 times at least. Insulating Transformer 5, 6, and 7 Input Terminal Minimum Power Application Time Time Accuracy Input Terminal Circuit GT3F Do not input signals using transistor output equipment of a voltage/current output type. Otherwise, the internal circuit may be damaged. Input Terminal 1 Max. measured value - Min. measured value × 100 (%) × 2 Maximum scale value Voltage Error This indicates the variance of operation time when the voltage at operation current varies within allowable voltage variance. Tv - Tr × 100 (%) Tr Tv: Average of measured operation time values at voltage V Tr: Average of measured operation time values at the raged voltage =± RY 10 Power Gate Input Start Input Reset Input • Do not connect input signal terminals of the GT3F timer to other terminals than No. 2. Never apply voltage to input signal terminals. Otherwise, the internal circuit may be damaged. • Input signal lines must be made as short as possible and installed away from power cables and power lines. Shielded wires or a separate conduit should be used for input wiring. • For contact input, use reliable gold-plated contacts to make sure that the residual voltage is less than 1V when the contacts are closed. 6 5 7 4 8 3 9 2 10 1 11 Power 1084 IDEC1066-1085.indd 1084 07.8.17 4:10:18 PM GT3 Series Multi-function Timers [Instructions] Temperature Error This indicates the influence caused by the change in temperature during operation within operating temperature. This is shown with the variance of operation time. Tt - T20 × 100 (%) T20 Tt: Average of operation times at temperature t T20: Average of operation times at reference temperature (20ºC) =± Operating Environment Flush Silhouette Temperature and Humidity Use the timer within the operating temperature and operating humidity ranges and prevent freezing and condensation. After storing below the operation temperature, leave the timer at room temperature for a sufficient period of time before use. Control Units Display Lights Environment Setting Error This indicates the gap between actual operation time and that on scale. Calculated from below formula, this is measured at any point but more than one-third of the maximum scale value. =± Average of measured values - Set value × 100 (%) Maximum scale value Prevent a corrosive gas such as sulfurous or ammonia gas, organic solvents (alcohol, benzine, thinner, etc.), strong alkaline substances or strong acids from touching to the timer, and do not use the timer in such an environment. Keep the timer from water splashes or steam. Vibration and Shock Load Current The rated current of the contact (or control output) should not be exceeded. Especially for inductive, capacitive, and incandescent lamp loads, the inrush current as large as a few to several tens times the rated current may cause welded contacts and other troubles. The amount of inrush current as well as steady-state current must be taken into consideration. Contact Protection Switching an inductive load generates a counter-electromotive force in the coil. The counter emf will cause arcing, which may shorten the contact life. Application of a protection circuit is recommended for contact protection. Rest Time When turning power off after time-out or during operation, allow a rest time longer than the reset time to restart. (Each model has a different reset time.) Continuous Energizing Since excessive vibrations or shocks cause the output contacts to open, the timer should be used within the operating extremes of vibration and shock resistance. Use of hold-down springs is recommended for secure mounting on sockets. Display Units Safety Products Terminal Blocks Comm. Terminals Noise and Static Charge Check the operation of the timer before using in an environment with a lot of noise. Install the input signal source, input signal wiring and timer away from noise source and high-voltage wire with noise as much as possible. Also, in case of using the timer under the environment with multiple static charge (pipe transportation of molding material, power/liquid material, etc.), place the timer away from such static charge source as well. AS-Interface Relays & Timers Sockets Others • The GT3F does not read the preset values of each selector after power is turned off. Note that minimizing the preset time does not shorten the delay time after power is turned off. • To make a sequence circuit by connecting timers and relays, check the timer operation sufficiently in consideration of the reset time of the timer. Circuit Protectors Power Supplies PLCs & SmartRelay Continuous energizing for a long period of time may damage the electrical characteristics of the timer because of internal heating. Use an additional relay to the output circuit and refrain from continuous energizing of the timer. Operator Interfaces Dielectric Strength Test Sensors When performing an insulation resistance or dielectric-strength test on control panels containing timers, make sure that the dielectric strength of the timer is not exceeded. In case the dielectric strength is exceeded, remove the timers from the panels. Control Stations Explosion Protection References 1085 IDEC1066-1085.indd 1085 07.8.17 4:10:19 PM