Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download 5220A Transconductance Amplifier
Document related concepts
Switched-mode power supply wikipedia , lookup
PID controller wikipedia , lookup
Negative feedback wikipedia , lookup
Current source wikipedia , lookup
Buck converter wikipedia , lookup
Public address system wikipedia , lookup
Alternating current wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
Audio power wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Transcript
5220A Transconductance Amplifier All All 5220A Transconductance Amplifier Product Home | Features | Specifications | Models, Options & Accessories The 5220A Transconductance Amplifier lets you calibrate alternating or direct current meters and shunts and the current functions of digital multimeters that measure up to 20A. A known input voltage of 1 to 20 volts produces a known output current of 1 to 20A. The 5220A is designed for those applications where 20A ac or dc current is required; for example, calibration of the upper ranges of digital multimeters, or used with a current coil to calibrate clamps and clamp meters. © 1995 - 2000 Fluke Corporation Privacy Statement http://www.fluke.com/products/home.asp?PID=8388 [2/22/2001 12:00:12 PM] 5220A Transconductance Amplifier Features All All 5220A Transconductance Amplifier Features Product Home | Features | Specifications | Models, Options & Accessories ● Built-in protection ● Remote operation ● May be programmed through a 5700A, 5720A or 5100B ● 20 amps output dc or rms ac ● ● ● 0.025% basic dc accuracy Over-voltage and over-current protection Over-temperature protection Built-in protection Protection is designed in to eliminate problems caused by excessive inputs, open inputs, and over compliance. Indicators on the front panel tell the user about any of these conditions. Automatic shut down occurs should the internal temperature rise excessively. Remote operation Drive voltage to the 5220A may be introduced through the front panel or the rear panel. The connector on the rear, however, allows the 5220A to become an extension to the current range of a 5700A, 5720A or 5100B Series Calibrator. The two instruments operate as one integrated calibration system with all the advantages of single control-point calibration; automatic error calculation, entry limit protection, etc. A 5100B Series Calibrator requires a Y5000 Interface/Buffer to control a 5220A. A single Y5000 Interface Buffer may also be used to control a 5205A Power Amplifier. May be programmed through a 5700A, 5720A or 5100B The 5220A is designed to be controlled by a Fluke 5700A/5720A or 5100B Series calibrator but may be driven by another voltage source such as the http://www.fluke.com/products/features.asp?SID=0&AGID=0&PID=8388 (1 of 2) [2/22/2001 12:00:49 PM] 5220A Transconductance Amplifier Features Fluke 5200A or 5500A. When used with a 5100B or 5700A/5720A the current range of those instruments is extended by a factor of 10 to 1. © 1995 - 2000 Fluke Corporation Privacy Statement http://www.fluke.com/products/features.asp?SID=0&AGID=0&PID=8388 (2 of 2) [2/22/2001 12:00:49 PM] 5220A Transconductance Amplifier Specifications All All 5220A Transconductance Amplifier Specifications Product Home | Features | Specifications | Models, Options & Accessories The 5220A is not CE certified and therefore not available in the European Community. ● Specifications Specifications DC Current Range: 0 to 20A Best 6 Month Specification: 0.025% of output AC Current Range: 0 to 20A Best 6 Month Specification: 0.05% of output © 1995 - 2000 Fluke Corporation Privacy Statement http://www.fluke.com/products/specifications.asp?SID=0&AGID=0&PID=8388 [2/22/2001 12:01:27 PM] 5220A Transconductance Amplifier Models, Options & Accessories All All 5220A Transconductance Amplifier Models, Options & Accessories Product Home | Features | Specifications | Models, Options & Accessories Model Name Product Description 5220A * Transconductance Amplifier Includes one-year product warranty, line cord, instruction manual, certificate of calibration practices *Not CE certified and therefore not available in the European Community Available Accessories and Options Model Name Accessory or Option Description M00-270-610 20” Slides for Rack Mount Kit M00-280-610 24” Slides for Rack Mount Kit M07-205-600 7: Rack Mount Kit Y5000 * Interface Buffer** Y5002 * Cable (Y5000 to 5220A)** Y5020 * Current Shunt Y5702 Cable (5700A to 5220A) *Accessories and options are not CE certified and therefore not available in the European community **Required when controlled from 5100B or 5101B © 1995 - 2000 Fluke Corporation Privacy Statement http://www.fluke.com/products/orderinfo.asp?SID=0&AGID=0&FID=8386 [2/22/2001 12:02:05 PM]
