Download POLARIS 5 APU Pure Hydrogen Power Generator 5 kW AC and DC

POLARIS 5
APU Pure Hydrogen Power Generator
5 kW AC and DC
POLARIS 5 is the new fuel cell auxiliary power unit (APU) system fuelled by pure hydrogen
to produce clean electrical power. POLARIS 5 is based on PEM fuel cell technology to
eliminate noise and vibration while maximizing durability, efficiency and environmental
friendliness. POLARIS 5 is designed for installation and use in countless applications that
require a high-quality power source. It is available in a variety of different configurations:
230 VAC single-phase grid-connected, 400 VAC three-phase grid-connected, and 48 VDC.
The POLARIS 5 system is a
combined heat and power unit
based on PEM – proton exchange
membrane – fuel cell technology.
Fuelled with pure hydrogen the
POLARIS 5 system is capable to
deliver 4,8 kW electricity and hot
water at 60°C. The system is equipped
with an electronic converter for
three different types of output
supply: a single-phase 220 V, 50/60
Hz; a three-phase 380V+neutral
and 48 VDC. The POLARIS 5
power conditioner transforms the
electric energy in continuous
current supplied from the stack at
220 VAC, 50 / 60 Hz single-phase
grid connected for domestic use.
Morphic Exergy
Via Buozzi 53-55-57
40057 Cadriano di Granarolo (BO), Italy
[email protected]
www.morphic.com
+39 51 675 11 29 Phone
POLARIS 5
5 kW AC and DC APU Pure Hydrogen Power Generator
PERFORMANCE
Net electric power: 1 to 4,8 kW and Idle
Voltage (depend of configuration): V 220
VAC / 380 VAC + Neutral / 48 VDC
System electric efficiency at nominal power: 41%
OPERATINGMODESGRIDCONNECTED
Start-up time: 12 sec to 0,5 kW, 1 min to full
power
Routine Maintenance Interval: 500 hr
Mass: 200 kg
MTBO: 500 hr
Locations: Outdoor
Operating temperature: 0 to 50˚C
Storage temperature: above 0˚C
Noise: 55 dBA at 1 m, Outdoor
HYDROGEN SUPPLY
Hydrogen Grade: 3.5 (EU)
Inlet pressure: 2–5 bar
Mass flow: Re-circulated
Anode stochiometry: 1,02
Fuel Consumption: 4,2 Nm3/hr at max power
COOLING – PRIMARY CIRCUIT
Water cooled: 65 °C
Circuit type: Closed circuit with
circulating pump
Required water quality: DI (< 5 S/cm) –
External water only required for initial fill
Water quantity: 2,5 lt
COOLING – SECONDARY CIRCUIT
Water cooled: Inlet min, 20 °C – max, 55 °C
outlet min, 25 °C – max, 60 °C
Circuit type: External pump is required
Required water quality: City line
INTERFACES
Front panel: Liquid crystal display.
Communication: Rs 232 serial port for
remote operation / CAN
OPERATING CONDITIONS
Environment temperature range for
operating: 0 °C / +50°C
Start up time up to 50% nominal power:
At 0°C min < 2
Environment temperature range for
depositing on the shelf: -30 °C / + 60°C
Percent of nominal power delivered at
extreme temperature: 70 %
WEIGHT AND SIZE
Length: 588 mm
Depth: 925 mm
Height: 649 mm
Weight: 120 kg
230 VAC SYSTEM TECHNICAL
CHARACTERISTICS
Fuel type: Hydrogen
Minimum pressure of the hydrogen: 2 bar
Electric supply: 230V-50/60Hz singlephase
Operating mode: Unit in parallel grid.
Capacity of electric supply: Completely
automatic from 2 kW to 4,8 kW
Thermal power: Transferred to the water
that flows through a liquid-liquid heat
exchanger that is part of the system.
The system is completely automatic. All
relevant system data can be transferred to
the acquisition system through a RS-232,
RS 485, CAN Bus port.
Available data: Stack temperature, Stack
current and voltage, Power, Supplied
electric energy (kWh), Operation
condition, Alarms.
Expected Lifetime: 10000 Hours.
SYSTEM CONNECTIONS
Use Dimensions
H2
1/4 inches
Co-gen IN
20 mm Co-gen OUT
20 mm Data communication:
Electrical connection: 1 ph: cables section 3x6 mm 2 3
3 ph: cables section 5x6 mm 2
48 VDC: cables section 70 mm 2
Connection type
NPT female
Water nipple
Water nipple
RS-232, RS 485, CAN Bus
Terminal
Specifications are subject to change without notice. Unless otherwise noted, all specifications are given at room temperature and pressure.
Morphic Exergy
Morphic Exergy is a company
within Morphic, a corporate
group based in Sweden with a
primary business focus on
renewable energy solutions. For
more than a decade, the key
personnel at Morphic Exergy has
amassed experience and know-
how in the development of proton
exchange membrane (PEM) fuel
cells and related systems, control
and software, DC power modules
and technical support technology
for global product support. On its
three automatic assembly lines,
Morphic Exergy manufactures
essential components such as
electrodes, membrane electrode
assemblies (MEAs), cells and
complete stacks, sensors and
controllers. A high production
capacity allows Morphic Exergy
to offer its superior end products
at competitive prices.