* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download LED- control gear (driver + dimmer) V
Electrical ballast wikipedia , lookup
Power engineering wikipedia , lookup
Power over Ethernet wikipedia , lookup
Power inverter wikipedia , lookup
Distributed control system wikipedia , lookup
Resilient control systems wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Three-phase electric power wikipedia , lookup
Control theory wikipedia , lookup
History of electric power transmission wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Electrical substation wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Current source wikipedia , lookup
Distribution management system wikipedia , lookup
Voltage regulator wikipedia , lookup
Stray voltage wikipedia , lookup
Power MOSFET wikipedia , lookup
Control system wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Power electronics wikipedia , lookup
Voltage optimisation wikipedia , lookup
Alternating current wikipedia , lookup
Surge protector wikipedia , lookup
Buck converter wikipedia , lookup
LCC30 LED- control gear (driver + dimmer) V-36030609 1 ) Properties 2 ) Controll 4 ) Size 5 ) Loop-in loop-out connection 6 ) Quick-locks 7 ) Screw mounting 8 ) Dip-Switch Vadsbo LightTech Aröds Industriväg 34 SE-422 43 Hisings Backa Sweden 3 ) Quickconnection Phone Fax E-mail Web 9 ) Functions and Protection +46-31-235600 +46-31-226010 [email protected] www.vadsbo.net Properties 1 ) Properties 5 ) Loop-in loop-out connection Dual terminals for quick and easy forward connction of phase, neutral and control cord. Up to 20 devices of totally 600W can be easily be controlled by a push button. The units are interconnected with standard installation cable via the optional control input. No separate sync cable required. 220-240 VAC Terminal. 2 ) Controll Primary side control: Push-button switch. Secondary side control (low voltage, SELV): 1-10Vdc control for example regulation with rotary dimmer or connection to KNX system. 7 ) Screw mounting Holes for screw mounting to a wall or similar. 8 ) DIP-Switch Using the DIP switch can set the type of LED you want to dim. Selectable constant currents 350mA 500mA 700mA 900mA Selectable constant voltsges 12Vdc 24Vdc 3 ) Quickconnection Quickconnection terminals for easy connection. 9 ) Functions and Protection 6 ) Quick-locks Equipped with quick-locks with strain relief 4 ) Size Easy to install in suspended ceiling thanks to its small dimensions. Easy entrance into a 65-70 mm hole, see picture on the next page. • Soft start • Memory Function • Constant Voltage Protection • Overload protection • Over temperature protection Unique Features Broad coverage of current and voltage range Synchronization without sync cable LED controller LCC30 covers all commonly occurring currents and voltages selectable via DIP switches such as 350, 500, 700 and 900 mA as well as 12 and 24 Vdc. Up to 20 LCC30 can be controlled by a push button that can be forward connected from control gear to control gear and requires no external synchronization cable. It is therefore possible to reach and control up to 600W of LED. Higher power of constant current diodes LED controller LCC30 have higher power range compared to commonly used alternatives *) on the market. LCC30 Other options *) Diode Power Number of diodes Number of diodes 350 mA 1-16 pcs 1W LED 1-12 pcs 1W LED 500 mA 1-15 pcs 2W LED 1-12 pcs 2W LED 700 mA 1-12 pcs 3W LED 1- 9 pcs 3W LED 900 mA 1- 7 pcs 4W LED Diode Voltage Diode Power 12Vdc 10,8W 10W 24Vdc 21,5W 20W - Mixed load Using common cabling allows multiple units to be synchronized. This means that you can set up such a device at 12Vdc, 350mA at another, a third at 700mA and get them to run and dim in a synchronized way with a single button! In this way you can use LCC30 for driving and dimming LED constant voltage stripes and LED constant current fixtures simultaneously. Independent of makes! Wiring diagram - example up to 600W L N L L N S S L N S L N S L N S Easy to install in suspended ceilings The dimensions of LCC30 makes the product userfriendly as it can be installed in ceilings. Remember to keep check on the ambient temperature. L N S L N S Insertion of LCC30 in 70 mm hole. Technical data LCC30 Constant Current (per output) 350mA (2-57V) 500mA (2-54V) 700mA (2-43V) 900mA (2-27V) 1-20W (1-16 pcs LED Vf=3,6) 2-27W (1-15 pcs LED Vf=3,6) 3-30W (1-11 pcs LED Vf=3,6) 4-24W (1-7 pcs LED Vf=3,6) Constant Voltage (per output) 12Vdc 24Vdc 10,8W 21,5W Item number V-36030609 Voltage Primary 220-240Vdc Ambient max temperature (Ta) +50°C Test temperature (Tc) +75°C Dimensions (LxWxH) 150x52x28 mm Weight 250 g Housing Thermoplastic Color White Protection against - Short circuit auto recovery - Overheating -:- Overload -:- Yes Yes Yes Connection - Primary (fast block) - Diversion of 230V and push button - Secondary (fast block) dimming 1,5 mm2 Yes 1,5 mm2 Dimming - Push button function - Potentiometer 1-10V (I = 0.35 mA) Yes Yes Dimring (function) Maximum number of vehicles that are controlled by one or more pushbuttons Cable lengths - Primary 20 pcs (no extra sync cable is required) 15 meters between the first driver and push button and between the drivers - Secondary 20 meters to the luminaire 40 meters in a loop Application areas - For installation - For detached service - Approved for mounting on furniture Yes Yes Yes Manufacturing standard EN 55015 EN 61347-1 Insulation class II Degree of protection IP20 Approval S/CE EMC requirements satisfied Yes Vadsbo LightTech Aröds Industriväg 34 SE-422 43 Hisings Backa Sweden Phone Fax E-mail Web +46-31-235600 +46-31-226010 [email protected] www.vadsbo.net EN 61547 EN 61347-2-13