Download LM1084 5A Low Dropout Positive Regulators

LM1084
5A Low Dropout Positive Regulators
General Description
Features
The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5V at 5A of load current.
It has the same pin-out as National Semiconductor’s industry
standard LM317.
The LM1084 is available in an adjustable version, which can
set the output voltage with only two external resistors. It is
also available in three fixed voltages: 3.3V, 5.0V and 12.0V.
The fixed versions intergrate the adjust resistors.
The LM1084 circuit includes a zener trimmed bandgap reference, current limiting and thermal shutdown.
The LM1084 series is available in TO-220 and TO-263 packages. Refer to the LM1085 for the 3A version, and the
LM1086 for the 1.5A version.
n
n
n
n
n
n
Available in 3.3V, 5.0V, 12V and Adjustable Versions
Current Limiting and Thermal Protection
Output Current
5A
Industrial Temperature Range
−40˚C to 125˚C
Line Regulation
0.015% (typical)
Load Regulation
0.1% (typical)
Applications
n Post Regulator for Switching DC/DC Conveter
n High Efficiency Linear Regulators
n Battery Charger
Connection Diagrams
TO-220
TO-263
DS100946-36
Top View
DS100946-35
Top View
Basic Functional Diagram, Adjustable Version
Application Circuit
DS100946-65
DS100946-52
1.2V to 15V Adjustable Regulator
© 2000 National Semiconductor Corporation
DS100946
www.national.com
LM1084 5A Low Dropout Positive Regulators
August 2000
LM1084
Ordering Information
Package
3-lead TO-263
3-lead TO-220
Temperature Range
Part Number
Transport Media
−40˚C to +125˚C
LM1084IS-ADJ
Rails
LM1084ISX-ADJ
Tape and Reel
−40˚C to + 125˚C
LM1084IS-12
Rails
LM1084ISX-12
Tape and Reel
LM1084IS-3.3
Rails
LM1084ISX-3.3
Tape and Reel
LM1084IS-5.0
Rails
LM1084ISX-5.0
Tape and Reel
LM1084IT-ADJ
Rails
LM1084IT-12
Rails
LM1084IT-3.3
Rails
LM1084IT-5.0
Rails
NSC Drawing
TS3B
T03B
Simplified Schematic
DS100946-34
www.national.com
2
Junction Temperature (TJ)(Note 3)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range
LM1084
Absolute Maximum Ratings (Note 1)
150˚C
-65˚C to 150˚C
Lead Temperature
260˚C, to 10 sec
ESD Tolerance (Note 4)
2000V
Maximum Input to Output Voltage Differential
Operating Ratings (Note 1)
LM1084-ADJ
29V
LM1084-12
18V
LM1084-3.3
27V
Control Section
−40˚C to 125˚C
LM1084-5.0
25V
Output Section
−40˚C to 150˚C
Power Dissipation (Note 2)
Junction Temperature Range (TJ) (Note 3)
Internally Limited
Electrical Characteristics
Typicals and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in Boldface type apply over the entire junction temperature range for operation.
Symbol
VREF
VOUT
∆VOUT
∆VOUT
Parameter
Reference Voltage
Output Voltage (Note
7)
Line Regulation
(Note 8)
Load Regulation
(Note 8)
Min
(Note
6)
Typ
(Note
5)
Max
(Note
6)
Units
1.238
1.225
1.250
1.250
1.262
1.270
V
V
LM1084-3.3
IOUT = 0mA, VIN = 8V
0 ≤ IOUT ≤IFULL LOAD, 4.8V≤ VIN ≤15V
3.270
3.235
3.300
3.300
3.330
3.365
V
V
LM1084-5.0
IOUT = 0mA, VIN = 8V
0 ≤ IOUT ≤ IFULL LOAD, 6.5V ≤ VIN ≤ 20V
4.950
4.900
5.000
5.000
5.050
5.100
V
V
LM1084-12
IOUT = 0mA, VIN = 15V
0 ≤ IOUT ≤ IFULL LOAD, 13.5V ≤ VIN ≤ 25V
11.880
11.760
12.000
12.000
12.120
12.240
V
V
0.015
0.035
0.2
0.2
%
%
LM1084-3.3
IOUT = 0mA, 4.8V ≤ VIN ≤ 15V
0.5
1.0
6
6
mV
mV
LM1084-5.0
IOUT = 0mA, 6.5V ≤ VIN ≤ 20V
0.5
1.0
10
10
mV
mV
LM1084-12
I OUT =0mA, 13.5V ≤ VIN ≤ 25V
1.0
2.0
25
25
mV
mV
0.1
0.2
0.3
0.4
%
%
LOAD
3
7
15
20
mV
mV
LOAD
5
10
20
35
mV
mV
12
24
36
72
mV
mV
1.3
1.5
V
Conditions
LM1084-ADJ
IOUT = 10mA, VIN−VOUT = 3V
10mA ≤IOUT ≤ IFULL LOAD,1.5V ≤ (VIN−VOUT) ≤ 25V
(Note 7)
LM1084-ADJ
IOUT =10mA, 1.5V≤ (VIN-VOUT) ≤ 15V
LM1084-ADJ
(VIN-V OUT) = 3V, 10mA ≤ IOUT ≤ IFULL
LM1084-3.3
VIN = 5V, 0 ≤ IOUT ≤ IFULL
LM1084-5.0
VIN = 8V, 0 ≤ IOUT ≤ IFULL
LM1084-12
VIN = 15V, 0 ≤ IOUT ≤ IFULL
Dropout Voltage
(Note 9)
LOAD
LM1084-3.3/5/12/ADJ
∆VREF = 1%, IOUT = 5A
3
LOAD
www.national.com
LM1084
Electrical Characteristics
(Continued)
Typicals and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in Boldface type apply over the entire junction temperature range for operation.
Symbol
ILIMIT
Min
(Note
6)
Typ
(Note
5)
LM1084-ADJ
VIN−VOUT = 5V
VIN−VOUT = 25V
5.5
0.3
8.0
0.6
A
A
LM1084-3.3
VIN = 8V
5.5
8.0
A
LM1084-5.0
VIN = 10V
5.5
8.0
A
LM1084-12
VIN = 17V
5.5
8.0
A
Parameter
Current Limit
Conditions
Max
(Note
6)
Units
Minimum Load
Current (Note 10)
LM1084-ADJ
VIN −VOUT = 25V
5
10.0
mA
Quiescent Current
LM1084-3.3
VIN = 18V
5.0
10.0
mA
LM1084-5.0
VIN ≤ 20V
5.0
10.0
mA
LM1084-12
VIN ≤ 25V
Thermal Regulation
TA = 25˚C, 30ms Pulse
Ripple Rejection
fRIPPLE = 120Hz, = COUT = 25µF Tantalum, IOUT = 5A
5.0
10.0
mA
0.003
0.015
%/W
LM1084-ADJ, CADJ, = 25µF, (VIN−VO) = 3V
60
75
dB
LM1084-3.3, VIN = 6.3V
60
72
dB
LM1084-5.0, VIN = 8V
60
68
dB
LM1084-12 VIN = 15V
54
60
dB
Adjust Pin Current
LM1084
55
120
µA
Adjust Pin Current
Change
10mA ≤ IOUT ≤ IFULL LOAD,
1.5V ≤ VIN−VOUT ≤ 25V
0.2
5
µA
Temperature Stability
0.5
Long Term Stability
TA =125˚C, 1000Hrs
RMS Output Noise
(% of VOUT)
10Hz ≤ f≤ 10kHz
Thermal Resistance
Junction-to-Case
3-Lead TO-263: Control Section/Output Section
3-Lead TO-220: Control Section/Output Section
0.3
%
1.0
0.003
%
%
0.65/2.7
0.65/2.7
˚C/W
˚C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Power dissipation is kept in a safe range by current limiting circuitry. Refer to Overload Recovery in Application Notes.
Note 3: The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature
is PD = (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Refer to Thermal Considerations in the Application Notes.
Note 4: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: IFULLLOAD is defined in the current limit curves. The IFULLLOAD Curve defines the current limit as a function of input-to-output voltage. Note that 30W power
dissipation for the LM1084 is only achievable over a limited range of input-to-output voltage.
Note 8: Load and line regulation are measured at constant junction temperature, and are guaranteed up to the maximum power dissipation of 30W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 9: Dropout voltage is specified over the full output current range of the device.
Note 10: The minimum output current required to maintain regulation.
www.national.com
4
LM1084
Typical Performance Characteristics
Dropout Voltage (VIN−VOUT)
Short-Circuit Current
DS100946-71
DS100946-63
Load Regulation
LM1084-ADJ Ripple Rejection
DS100946-38
DS100946-43
LM1084-ADJ Ripple Rejection vs Current
Temperature Stability
DS100946-90
DS100946-25
5
www.national.com
LM1084
Typical Performance Characteristics
(Continued)
Adjust Pin Current
LM1084-ADJ Load Transient Response
DS100946-69
DS100946-26
LM1084-ADJ LineTransient Response
Maximum Power Dissipation
DS100946-68
DS100946-70
www.national.com
6
General
crease phase margin and thus increase stability. The equivalent series resistance (ESR) of solid tantalum or aluminum
electrolytic capacitors is used to provide the appropriate zero
(approximately 500 kHz).
Figure 1 shows a basic functional diagram for the
LM1084-Adj (excluding protection circuitry) . The topology is
basically that of the LM317 except for the pass transistor. Instead of a Darlingtion NPN with its two diode voltage drop,
the LM1084 uses a single NPN. This results in a lower dropout voltage. The structure of the pass transistor is also
known as a quasi LDO. The advantage a quasi LDO over a
PNP LDO is its inherently lower quiescent current. The
LM1084 is guaranteed to provide a minimum dropout voltage 1.5V over temperature, at full load.
The Aluminum electrolytic are less expensive than tantalums, but their ESR varies exponentially at cold temperatures; therefore requiring close examination when choosing
the desired transient response over temperature. Tantalums
are a convenient choice because their ESR varies less than
2:1 over temperature.
The recommended load/decoupling capacitance is a 10uF
tantalum or a 50uF aluminum. These values will assure stability for the majority of applications.
The adjustable versions allows an additional capacitor to be
used at the ADJ pin to increase ripple rejection. If this is done
the output capacitor should be increased to 22uF for tantalums or to 150uF for aluminum.
Capacitors other than tantalum or aluminum can be used at
the adjust pin and the input pin. A 10uF capacitor is a reasonable value at the input. See Ripple Rejection section regarding the value for the adjust pin capacitor.
It is desirable to have large output capacitance for applications that entail large changes in load current (microprocessors for example). The higher the capacitance, the larger the
available charge per demand. It is also desirable to provide
low ESR to reduce the change in output voltage:
∆V = ∆I x ESR
It is common practice to use several tantalum and ceramic
capacitors in parallel to reduce this change in the output voltage by reducing the overall ESR.
Output capacitance can be increased indefinitely to improve
transient response and stability.
Ripple Rejection
Ripple rejection is a function of the open loop gain within the
feed-back loop (refer to Figure 1 and Figure 2). The LM1084
exhibits 75dB of ripple rejection (typ.). When adjusted for
voltages higher than VREF, the ripple rejection decreases as
function of adjustment gain: (1+R1/R2) or VO/VREF. Therefore a 5V adjustment decreases ripple rejection by a factor of
four (−12dB); Output ripple increases as adjustment voltage
increases.
However, the adjustable version allows this degradation of
ripple rejection to be compensated. The adjust terminal can
be bypassed to ground with a capacitor (CADJ). The impedance of the CADJ should be equal to or less than R1 at the
desired ripple frequency. This bypass capacitor prevents
ripple from being amplified as the output voltage is increased.
1/(2π*fRIPPLE*CADJ) ≤ R1
DS100946-65
FIGURE 1. Basic Functional Diagram for the LM1084,
excluding Protection circuitry
Output Voltage
The LM1084 adjustable version develops at 1.25V reference
voltage, (VREF), between the output and the adjust terminal.
As shown in figure 2, this voltage is applied across resistor
R1 to generate a constant current I1. This constant current
then flows through R2. The resulting voltage drop across R2
adds to the reference voltage to sets the desired output voltage.
The current IADJ from the adjustment terminal introduces an
output error . But since it is small (120uA max), it becomes
negligible when R1 is in the 100Ω range.
For fixed voltage devices, R1 and R2 are integrated inside
the devices.
Load Regulation
The LM1084 regulates the voltage that appears between its
output and ground pins, or between its output and adjust
pins. In some cases, line resistances can introduce errors to
the voltage across the load. To obtain the best load regulation, a few precautions are needed.
DS100946-17
FIGURE 2. Basic Adjustable Regulator
Figure 3 shows a typical application using a fixed output
regulator. Rt1 and Rt2 are the line resistances. VLOAD is less
than the VOUT by the sum of the voltage drops along the line
resistances. In this case, the load regulation seen at the
RLOAD would be degraded from the data sheet specification.
Stability Consideration
Stability consideration primarily concern the phase response
of the feedback loop. In order for stable operation, the loop
must maintain negative feedback. The LM1084 requires a
certain amount series resistance with capacitive loads. This
series resistance introduces a zero within the loop to in7
www.national.com
LM1084
APPLICATION NOTE
LM1084
APPLICATION NOTE
withstand microsecond surge currents of 10A to 20A. With
an extremely large output capacitor (≥1000 µf), and with input instantaneously shorted to ground, the regulator could
be damaged. In this case, an external diode is recommended between the output and input pins to protect the
regulator, shown in Figure 5.
(Continued)
To improve this, the load should be tied directly to the output
terminal on the positive side and directly tied to the ground
terminal on the negative side.
DS100946-18
FIGURE 3. Typical Application using Fixed Output
Regulator
When the adjustable regulator is used (Figure 4), the best
performance is obtained with the positive side of the resistor
R1 tied directly to the output terminal of the regulator rather
than near the load. This eliminates line drops from appearing
effectively in series with the reference and degrading regulation. For example, a 5V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due
to line resistance of 0.05Ω x IL. If R1 (=125Ω) is connected
near the load the effective line resistance will be 0.05Ω (1 +
R2/R1) or in this case, it is 4 times worse. In addition, the
ground side of the resistor R2 can be returned near the
ground of the load to provide remote ground sensing and improve load regulation.
DS100946-15
FIGURE 5. Regulator with Protection Diode
Overload Recovery
Overload recovery refers to regulator’s ability to recover from
a short circuited output. A key factor in the recovery process
is the current limiting used to protect the output from drawing
too much power. The current limiting circuit reduces the output current as the input to output differential increases. Refer
to short circuit curve in the curve section.
During normal start-up, the input to output differential is
small since the output follows the input. But, if the output is
shorted, then the recovery involves a large input to output
differential. Sometimes during this condition the current limiting circuit is slow in recovering. If the limited current is too
low to develop a voltage at the output, the voltage will stabilize at a lower level. Under these conditions it may be necessary to recycle the power of the regulator in order to get the
smaller differential voltage and thus adequate start up conditions. Refer to curve section for the short circuit current vs.
input differential voltage.
Thermal Considerations
ICs heats up when in operation, and power consumption is
one factor in how hot it gets. The other factor is how well the
heat is dissipated. Heat dissipation is predictable by knowing
the thermal resistance between the IC and ambient (θJA).
Thermal resistance has units of temperature per power
(C/W). The higher the thermal resistance, the hotter the IC.
The LM1084 specifies the thermal resistance for each package as junction to case (θJC). In order to get the total resistance to ambient (θJA), two other thermal resistance must be
added, one for case to heat-sink (θCH) and one for heatsink
to ambient (θHA). The junction temperature can be predicted
as follows:
TJ = TA + PD (θJC + θCH + θHA) = TA + PD θJA
DS100946-19
FIGURE 4. Best Load Regulation using Adjustable
Output Regulator
3.0 Protection Diodes
Under normal operation, the LM1084 regulator does not
need any protection diode. With the adjustable device, the
internal resistance between the adjustment and output terminals limits the current. No diode is needed to divert the current around the regulator even with a capacitor on the adjustment terminal. The adjust pin can take a transient signal of
± 25V with respect to the output voltage without damaging
the device.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the regulator, and rate of decrease of VIN. In the LM1084 regulator,
the internal diode between the output and input pins can
www.national.com
TJ is junction temperature, TA is ambient temperature, and
PD is the power consumption of the device. Device power
consumption is calculated as follows:
IIN = IL + IG
PD = (VIN−VOUT) IL + VINIG
8
LM1084
APPLICATION NOTE
(Continued)
Figure 6 shows the voltages and currents which are present
in the circuit.
DS100946-16
FIGURE 6. Power Dissipation Diagram
Once the devices power is determined, the maximum allowable (θJA (max)) is calculated as:
θJA (max) = TR(max)/PD = TJ(max) − TA(max)/PD
The LM1084 has different temperature specifications for two
different sections of the IC: the control section and the output
section. The Electrical Characteristics table shows the junction to case thermal resistances for each of these sections,
while the maximum junction temperatures (TJ(max)) for each
section is listed in the Absolute Maximum section of the
datasheet. TJ(max) is 125˚C for the control section, while TJ(max) is 150˚C for the output section.
θJA (max) should be calculated separately for each section as
follows:
θJA (max, CONTROL SECTION) = (125˚C - TA(max))/PD
θJA (max, OUTPUT SECTION) = (150˚C - TA(max))PD
The required heat sink is determined by calculating its required thermal resistance (θHA (max)).
θHA (max) = θJA (max) − (θJC + θCH)
(θHA (max)) should also be calculated twice as follows:
(θHA (max)) = θJA (max, CONTROL SECTION) - (θJC (CONTROL SECTION) + θCH)
(θHA (max)) = θJA(max, OUTPUT SECTION) - (θJC (OUTPUT
SECTION) + θCH)
If thermal compound is used, θCH can be estimated at 0.2
C/W. If the case is soldered to the heat sink, then a θCH can
be estimated as 0 C/W.
After, θHA (max) is calculated for each section, choose the
lower of the two θHA (max) values to determine the appropriate heat sink.
If PC board copper is going to be used as a heat sink, then
Figure 7 can be used to determine the appropriate area
(size) of copper foil required.
DS100946-64
FIGURE 7. Heat sink thermal Resistance vs Area
9
www.national.com
LM1084
Typical Applications
DS100946-67
5V to 3.3V, 5A Regulator
DS100946-50
Adjustable @ 5V
DS100946-53
5V Regulator with Shutdown
DS100946-52
1.2V to 15V Adjustable Regulator
DS100946-55
Adjustable Fixed Regulator
DS100946-54
Battery Charger
DS100946-56
Regulator with Reference
DS100946-57
High Current Lamp Driver Protection
www.national.com
10
LM1084
Typical Applications
(Continued)
DS100946-60
DS100946-59
Ripple Rejection Enhancement
Battery Backup Regulated Supply
DS100946-62
DS100946-61
Generating Negative Supply voltage
Automatic Light control
DS100946-58
Remote Sensing
11
www.national.com
LM1084
Physical Dimensions
inches (millimeters) unless otherwise noted
3-Lead TO-263 Package
Order Number LM1084S-ADJ, LM1084S-3.3, LM1084S-5.0, or LM1084S-12
NSC Package Number TS3B
www.national.com
12
LM1084 5A Low Dropout Positive Regulators
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead TO-220 Package
Order Number LM1084T-ADJ, LM1084T-3.3, LM1084T-5.0, or LM1084T-12
NSC Package Number T03B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.