Download EBC5855X Quick Reference Guide

EBC5855X Quick Reference Guide
All-in-One Pentium-M Single Board with LCD, AC97 Audio, 6 USB 2.0,
Intel 10/100/1000Base-Tx Ethernet Interfaces, 2COMs
User’s Quick Start Card
Version 1.0
http://www.bcmcom.com
Inspect the Package:
Jumper and Connector List
Connectors on the board are linked to external devices such as hard disk drives, a keyboard,
or floppy drives. In addition, the board has a number of jumpers that allow you to configure
your system to suit your application.
The following tables list the function of each of the board's jumpers and connectors.
The following tables list the function of each of the board's jumpers and connectors.
Jumpers
„
„
„
1 EBC-5855X series All-in-One Pentium-M Computing Module
1 Quick Installation Guide
Cable set includes the followings:
— 1 IDE cable (44-pin 2.0mmto 40-pin, pitch 2.54mm)
— 2 cable for USB 2.0 (10-pin, pitch 2.54mm)
— 1 Power Adapter cable (8 Pin to 20 Pin Block)
— 1 Parallel port cable
— 1 CPU Heatsink/ Fan with Mounting Bracket
If any of these items are missing or damaged, please contact your
distributor or sales representative immediately.
Copyright Notice
Copyright © 2006 BCM Advanced Research, ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the prior written permission of the
original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
BCM Advanced Research reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve design
and/or performance. BCM assumes no responsibility or liabilities for the use of the described
product(s), conveys no license or title under any patent, copyright, or mask work rights to these
products, and makes no representations or warranties that these products are free from patent,
copyright, or mask work right infringement, unless otherwise specified. Applications that are
described in this manual are for illustration purposes only. BCM Advanced Research makes no
representation or warranty that such application will be suitable for the specified use without further
testing or modification.
WARNING: Electrostatic Sensitive Device (ESD)
Static electricity can easily damage your motherboard and will void your motherboard warranty. Keep the
motherboard and other system components in their anti-static packaging until you are ready to install them.
Touch a grounded surface before you remove any system component from its protective anti-static
packaging. Unpacking and installation should be done on a grounded, anti-static mat. The operator should
be wearing an anti-static wristband, grounded at the same points as the anti-static mat. During
configuration and installation touch a grounded surface frequently to discharge any static electrical charge
that may have built up in your body. Avoid touching the components when handling the motherboard or a
peripheral card. Handle the motherboard and peripheral cards either by the edges or by the peripheral card
case-mounting bracket.
WARNING: Misplaced Jumper Damage
Incorrect setting jumpers and connectors may lead to damage to your motherboard and will void your
motherboard warranty. Please pay special attention not to connect these headers in wrong directions. DO
NOT change ANY jumpers while the motherboard has the power!
ATTENTION: Incorrect BIOS Setup
If you do not know how to handle BIOS setup or how to set it up properly, it is strongly advisable
that you do not modify any of the settings than otherwise instructed in the User’s Quick Start Card.
Even a seemingly small incorrect adjustment or modification in the BIOS setup can render your
system unstable or unusable. The incorrect BIOS setup is not covered by your motherboard’s
manufacturer warranty.
Functions
JP1
Clear CMOS Setting Select
JP2
Watchdog Timer Setting Select
JP3
CPU Type Setting Select
JP4
FAN1 Voltage Setting Select
JP5
FAN2 Voltage Setting Select
Connectors
CN1
CN2
CN3
CN4
CN6
CN7
CN8
CN9
CN10
CN11
CN12
CN13
CN14
CN15
CN16
CN17
CN18
CN19
Functions
Slim Floppy Disk Connector
Secondary IDE Connector
Primary IDE Connector
CD-IN Connector
Gigabit Ethernet RJ-45 & USB 0/1 Connectors
Parallel Port Connector
USB 4/5 (Pin-Header) Connector
USB 2/3 (Pin-Header) Connector
Fan1 Power Connector
CRT VGA & Audio Port Connectors
LVDS Panel Interface
LVDS Power Connector
COM1 & COM2 RS-232 Serial Port Connectors
System Panel Indicate Connector
IrDA Connector
Fan2 Power Connector
PS/2 Keyboard & Mouse Connectors
8-pins ATX Power Connector
WARNING: CMOS Battery Damage
Replace your system’s CMOS RAM battery only with the identical BR-2032 3V Lithium-Ion coin cell
(or equivalent) battery type to avoid risk of personal injury or physical damage to your equipment.
Always dispose of used batteries according to the manufacturer’s instructions, or as required by
the local ordinance (where applicable). The damage due to not following this warning will void
your motherboard’s manufacturer warranty.