* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Data Sheet KW941
Pulse-width modulation wikipedia , lookup
Current source wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Electrical substation wikipedia , lookup
Transmission line loudspeaker wikipedia , lookup
History of electric power transmission wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Flip-flop (electronics) wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Power inverter wikipedia , lookup
Phone connector (audio) wikipedia , lookup
Stray voltage wikipedia , lookup
Alternating current wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Distribution management system wikipedia , lookup
Integrating ADC wikipedia , lookup
Voltage optimisation wikipedia , lookup
Buck converter wikipedia , lookup
Voltage regulator wikipedia , lookup
Power electronics wikipedia , lookup
Schmitt trigger wikipedia , lookup
Mains electricity wikipedia , lookup
Current mirror wikipedia , lookup
Switched-mode power supply wikipedia , lookup
KW941-BP World Leaders in Interfacing and Retransmission POSITIVE or NEGATIVE VOLTAGE STEPPER GYRO RETRANSMISSION UNIT INTRODUCTION The KW941-BP converts heading data into traditional DC stepper transmission of 6 steps per degree. Using the KW941-BP allows a new heading sensor such as a gyro, magnetic compass or satellite compass to connect to existing bridge repeaters, radars and navigational aids. A M I M ARINE (UK) LTD Unit 2 Tower Industrial Est. Tower Lane Eastleigh Southampton SO50 6NZ UK Phone: +44(0)2380 480450 E-mail: [email protected] The bi-polar (+/- polarity) step voltage output suits the popular stepper voltage. The interface has a single stepper output for connection to the distribution unit. With step input the step output is the same, except that false states are removed. An additional feature of the KW941-BP is itβs ability to act as a stepper amplifier. With stepper input voltages from 4 to 35v and amplified to 70vDC 250mm 150mm 350mm 300mm ALL FIXING HOLES 10mm KW941-BP 200mm GLAND PLATE World Leaders in Interfacing and Retransmission World Leaders in SPECIFICATION INPUT: NMEA 0183. $HEHDT, $GPHDT and all valid heading sentences. Or Furuno clock and data. Or Standard stepper 6 steps per degree. +/-4 to 35 volts. OUTPUT: 6 steps per degree. Single output for feeding to a distribution unit. Output voltage nominal 24v, 35v, 50v, 70v, (3 Amps per line) 2 standard transformers, please specify which type you require: a) 24v/50v b) 35v/70v. The output voltage will vary with the load as it is not a regulated supply. Rotation or follow up 12 or 24 degrees per second from NMEA OUTPUT: NMEA 0183. RS232 and RS422 compatible. (For test and monitor purpose.) Sentence $HEHDT (This is not aligned in the step input mode.) OUTPUT: Alarm relay energised when OK. 1 Amp DIL relay for an independent alarm. Interfacing and Retransmission CONNECTORS: Removable terminal blocks. Power is orange snap-in connector. A M I M ARINE (UK) LTD Unit 2 Tower Industrial Est. Tower Lane AMI Marine (UK) Ltd Eastleigh Unit 2 Southampton Tower Industrial Est. SO50Lane 6NZ Tower UK Eastleigh Phone:Southampton +44(0)2380 480450 E-mail: [email protected] SO50 6NZ POWER: Nominal 115 volts or 230 volts 50/60 Hz double fused, switched and filtered. HOUSING: 350 x 250 x 150 standard electrical enclosure with door. FEATURES: LEDs on all inputs and outputs. Simple design. Watchdog restart circuit. DIFFERENCES FROM THE MODEL KW941-D: Both + and β step voltage is output (instead of β steps only) so that AMI can interface the two polarities of repeater. A single stepper output connector is fitted for connection to a separate distribution unit, instead of having 6 outlets on the board. Stepper input is now + or β steps.