Download The electromagnetic interference - International Conference on

Electromagnetic Compatibility
Grzegorz Kosobudzki; Jerzy Leszczyński
Introduction to EMC
Electromagnetic compatibility (EMC)
the ability of a system or equipment to operate within
design tolerances in its intended environment, with
adjacent systems and equipment, and with itself, so
that the effect of any electromagnetic disturbances
produced by the systems or equipment is reduced.
2
Electromagnetic compatibility (EMC)
Intrasystem
interference
Electromagnetic
environment
Electromagnetic
environment
Electromagnetic
disturbances
Equipement,
Device or
System
Electromagnetic
disturbances
emmision
3
Electromagnetic compatibility (EMC)
Electromagnetic
Compatibility
Electromagnetic
emmision
Electromagnetic
susceptibility
4
Electromagnetic interference (EMI)
A phenomenon in which electronic devices upset
each other’s operation. Computers, television
receivers, telephone sets, high-fidelity sound
equipment, and certain medical devices can
malfunction because of strong radio-frequency
fields such as those from a nearby broadcast
transmitter. The EMI is usually the result of
improper or ineffective shielding in the affected
device or system.
5
Electromagnetic compatibility
frequency range




DC
Power line frequency 50,60,400 Hz
Low frequency 50…150kHz
High frequency >150kHz (Radio frequency)
6
7
The electromagnetic interference (EMI)
coupling channel
Source of
electromagnetic
disturbances
Coupling path
Electromagnetic
Common impedance
Magnetic field
Electric field
Victim
(equipement)
(Radiative)
(Conductive)
(Inductive)
(Capacitive)
7
Principal phenomena causing electromagnetic disturbances as classified by the IEC
Group
Exemples
Conducted low frequency phenomena Harmonic, interharmonic, DC in AC networks
Signal system (power line carrier)
Voltage dips, interruption,fluctuation, imbalance
Power frequency variation
Induced low frequency voltages
Radiated low frequency phenomena
Magnetic fields, Electric fields
Conducted high frequency
phenomena
Induced continuous wave voltage or current
Radiated high frequency phenomena
Magnetic fields, Electric fields, electromagnetic fields
Oscillatory transient, Unidirectionat transient
Transients, continuous waves
Electrostatic discharge (ESD)
Nuclear electromagnetic pulse (NEMP)
8
Conductive interference
LOAD
Ion=1A
+5V
Vcc
Temperature
sensor
Vo=10mV/oC
Power Supply
Vm
B
Vm=Vo+VAB
Shared current path
GND
A
9
Conductive interference
LOAD
Ion=1A
+5V
Vcc
Temperature
sensor
Vo=10mV/oC
Power Supply
Vm
Vm=Vo
GND
A
10
Inductive interference
In
Vn - Noise source
Magnetic flux coupling
R
L
Vs - Signal source
Vs
Vn
R
L
M
11
Capacitive interference
Vn - Noise source
Electrical field
Vs - Signal source
R
L
Cef
R
L
Vs - Signal source
12
Emmision limit,immunity limit, compatibility
level and planning level
Probability density
Emmision
Limit
Emmision
Level
Compatibility
Level
Equipement
Compatibility
Level
Planning
Level
Immunity
Limit
Disturbance level
13
Emmision limit,immunity limit, compatibility
level and planning level
Immunity Level
Disturbance Level
Construction Immunity
Margin
Immunity Limit
Immunity Margin
Compatibility Margin
Compatibility Level
Emmision Margin
Emmision Limit
Construction
Emmision Margin
Emmision Level
Independent variable
14
Power Quality – Part of EMC
Power Quality: The concept of powering and
grounding electronic equipment in a manner that
is suitable to the operation of that equipment and
compatible with premise wiring system and other
connected equipment
IEEE std 1159 definition
15
Power Quality – Part of EMC
Coupling path – conductive (Power Distribution System )
Equipement: Immunity on disturbances in power system
Emmision disturbances to power system
Enviroment: power system voltage parameters
16
How are Disturbances prevented?
•Use shielded gaskets to seal doors and
flanges
•Fit an EMC filter on the incoming power side
•Keep signal cables away from power cables
•Use screened cables and use EMC glands for
360 degree earth bonding on both ends
17
Electromagnetic compatibility
Overview of Standards (IEC 61000 series)
• 1: General : General consideration (fundamental principles).
• 2: Enviroment : Description and classification of environment.
Captatibility levels.
• 3: Emmision limits and immunity test levels.
• 4: Testing and measurement techniques
• 5: Installation and mitigation guidelines
• 6: Generic standards.
• 9: Miscellaneous
18
Enviroment
• EN 61000-2-2 - Compatibility levels for low-frequency conducted
disturbances and signalling in public low-voltage power supply
systems
• EN 61000-2-4 - Compatibility levels in industrial plants for lowfrequency conducted disturbances
• EN 61000-2-9 - Description of HEMP environment - Radiated
disturbance. Basic EMC publication
• EN 61000-2-10 - Description of HEMP environment - Conducted
disturbance
• EN 61000-2-12 -Environment - Compatibility levels for low-frequency
conducted disturbances and signalling in public medium-voltage
power supply systems
19
Limits
• EN 61000-3-2 - Limits for harmonic current emissions (equipment
input current ≤16 A per phase) .
• EN 61000-3-3 - Limitation of voltage changes, voltage fluctuations
and flicker in public low-voltage supply systems, for equipment with
rated current ≤16 A per phase and not subject to conditional
connection
• EN 61000-3-11 - Limitation of voltage changes, voltage fluctuations
and flicker in public low-voltage supply systems - Equipment with
rated current ≤ 75 A and subjet to conditional connection.
• EN 61000-3-12 - Limits for harmonic currents produced by equipment
connected to public low-voltage systems with input current > 16 A
and ≤ 75 A per phase
20
Testing and measurement techniques-1
• EN 61000-4-2 - Electrostatic discharge immunity test
• EN 61000-4-3:2006 - Radiated, radio-frequency,
electromagnetic field immunity test.
• EN 61000-4-4:2004 - Electrical fast transient/burst
immunity test.
• EN 61000-4-5 –Surge immunity test
• EN 61000-4-6 -Immunity to conducted disturbances,
induced by radio-frequency fields
21
Testing and measurement techniques-2
•
•
•
•
EN 61000-4-8 - Power frequency magnetic field immunity test.
EN 61000-4-9 - Pulse magnetic field immunity test
EN 61000-4-10 - Damped oscillatory magnetic field immunity test.
EN 61000-4-11 - Voltage dips, short interruptions and voltage
variations immunity tests .
• EN 61000-4-34 - Voltage dips, short interruptions and voltage
variations immunity tests for equipment with input current more
than 16 A per phase
• EN 61000-4-14 - Voltage fluctuation immunity test for equipment
with input current not exceeding 16 A per phase.
22
Testing and measurement techniques-3
• EN 61000-4-13 - Harmonics and interharmonics including mains
signalling at a.c. power port, low frequency immunity tests
• EN 61000-4-12 - Ring wave immunity test .
• EN 61000-4-18:2007 - Damped oscillatory wave immunity test
• EN 61000-4-16 - Test for immunity to conducted, common mode
disturbances in the frequency range 0 Hz to 150 kHz.
• EN 61000-4-17 - Ripple on d.c. input power port immunity test.
• EN 61000-4-20 - Emission and immunity testing in transverse
electromagnetic (TEM) waveguides
23
Testing and measurement techniques-4
• EN 61000-4-21 - Reverberation chamber test methods.
• EN 61000-4-23 - Test methods for protective devices for HEMP and
other radiated disturbances .
• EN 61000-4-24 - Test methods for protective devices for HEMP
conducted disturbance - Basic EMC Publication.
• EN 61000-4-25 - HEMP immunity test methods for equipment and
systems
• EN 61000-4-27 - Unbalance, immunity test for equipment with input
current not exceeding 16 A per phase.
• EN 61000-4-28 - Variation of power frequency, immunity test for
equipment with input current not exceeding 16 A per phase .
• EN 61000-4-29 - Voltage dips, short interruptions and voltage
variations on d.c. input power port immunity tests
24
Testing and measurement techniques-5
• EN 61000-4-7 - General guide on harmonics and
interharmonics measurements and instrumentation, for
power supply systems and equipment connected thereto
• EN 61000-4-15 - Flickermeter - Functional and design
specifications.
• EN 61000-4-30 –Power quality measurement methods
25
Installation and mitigation guidelines
• EN 61000-5-5 - Specification of protective devices for
HEMP conducted disturbance. Basic EMC Publication.
• EN 61000-5-8 - HEMP protection methods for the
distributed infrastructure
26
Generic standards
• EN 61000-6-1 - Immunity for residential, commercial and
light-industrial environments
• EN 61000-6-2 - Immunity for industrial environments
• EN 61000-6-3 - Emission standard for residential,
commercial and light-industrial environments
• EN 61000-6-4 - Emission standard for industrial
environments
27
International Electrotechnical
Commission
The IEC is the world's leading organization that prepares
and publishes International Standards for all electrical,
electronic and related technologies — collectively
known as „electrotechnology”
28
CISPR
The Special International Committee on Radio
Interference (abbreviated CISPR from the French name
of the organization, Comité international spécial des
perturbations radioélectriques) is concerned with
developing norms for detecting, measuring and
comparing electromagnetic interference in electric
devices. Its members are partially also in the
International Electrotechnical Commission (IEC). It was
founded in 1934.
29
References and useful links
•
•
•
•
•
•
•
www.iec.ch ; www.pkn.pl
www.lpqi.org
www.schaffner.com
www.teseq.com;
www.miedz.org.pl
www.reo.co.uk
www.emtest.com
30
References and useful links
• C. Sankaran – ”Power quality” – CRC press 2002
• A.Baggini –”Handbook of Power Quality” – John Wiley &
Sons 2008
• R.C.Dugan, M.F. McGranaghan, H.W Beaty – „Electrical
Power System Quality”-McGraw-Hill 1996
• Kenneth L. Kaiser – „Electromagnetic Compatibility
Handbook” – CRC Press 2005
31