Download led built-in modules

LUGA Shop 2013 – LED Modules COB for Retail Environments
LED BUILT-IN
MODULES
LUGA SHOP 2013 HE HiCRI
5000 lm
LUGA SHOP 2013 HiCRI –
LED MODULES COB FOR
RETAIL ENVIRONMENTS
WU-M-466 HiCRI
Typical Applications
• Integration in reflector luminaires
• Shop lighting
• Furniture lighting
• Flat surface-mounting luminaires
• Cladding illumination
• Stairway and corridor illumination
• Suspended luminaire with external control gear
LUGA Shop 2013 HE HiCRI
¢ LONG SERVICE LIFETIME: 50,000 HOURS (L90; F10)
¢ VERY COMPACT SHAPE
¢ HIGHLY EFFICIENT: UP TO 133 LM/W AT Tp = 65 °C
¢ HIGH COLOUR RENDERING CRI: Ra > 90
istockphoto.com
¢ NARROW COLOUR TOLERANCES:
3 STEP MACADAMS (INITIAL)
4 STEP MACADAMS (AFTER 50,000 HRS)
¢ INTEGRATED THERMAL PROTECTION
¢ VDE APPROVED (ACC. TO EN 62031)
pending
A Member of the Panasonic Group
Vossloh-Schwabe Deutschland GmbH · Hohe Steinert 8 · 58509 Lüdenscheid · Germany · Phone +49 23 51/10 10 · Fax +49 23 51/10 12 17 · www.vossloh-schwabe.com
LUGA Shop 2013 – LED Modules COB for Retail Environments
LUGA Shop 2013
HE HiCRI 5000 lm
Technical Notes
• Dimensions: Ø 46.6 x 45.5 mm
• Use of external LED constant current driver
• Temperature fail-safe circuit
(activation temperature: tc »105 °C)
• On-board push-in connector
Electrical Characteristics
at tp = 65 °C
Ref. No.
Type
WU-M-466
Colour
All types
Typ. voltage DC
warm white / neutral white
Typ. power consumption
500 mA
700 mA
1050 mA 1400 mA 500 mA
700 mA
1050 mA 1400 mA
V
V
V
V
W
W
W
W
37.9
38.4
39.7
40.9
18.9
26.9
41.7
57.2
Voltage and power tolerance: ±10 %
Maximum Ratings
Exceeding the maximum ratings can lead to reduction of service life or destruction of the modules.
Type
Operation temperature
Ambient temperature range
Storage temperature range
range at tc-point
Alle Typen
Max. allowed
Max. permitted output
operating current
voltage of operating device
°C min.
°C max.
°C min.
°C max.
°C min.
°C max.
mA
V
–25
+85
–25
+40
–40
+85
2590
60
Optical Characteristics
at tp = 65 °C
Ref. No.
Type
Colour
Correlated colour Typ. luminous flux** and efficiency at
temperature*
500 mA
K
lm
lm/W
lm
Typ.
CRI
1050 mA
1400 mA
beam
Ra
metric
lm/W
lm
lm
angle (°)
typ.
code
700 mA
lm/W
lm/W
Photo-
WU-M-466-927 552158
warm white
2700
2140
113
2895
108
4055
97
5030
88
120
95
927/349
WU-M-466-930 552160
warm white
3000
2270
120
3085
115
4315
103
5415
95
120
95
930/349
WU-M-466-935 552163
neutral white 3500
2395
127
3260
121
4590
110
5730
100
120
95
935/349
WU-M-466-940 552165
neutral white 4000
2520
133
3415
127
4855
116
6000
105
120
95
940/349
* Colour tolerance: 3 MacAdams | ** Production tolerance of luminous flux and efficiency: ± 10 % | Min. CRI Ra: > 90
Packing unit: 20 pcs.
Mechanical Dimensions
Operating Life
at tp = 65 °C
LE
WU-M-466
maintenance
IF 500 mA
IF 700 mA
IF 1050 mA
IF 1400 mA
L90/F10*
62,000 hrs
57,000 hrs
50,000 hrs
39,000 hrs
L80/F10*
67,000 hrs
63,000 hrs
60,000 hrs
50,000 hrs
L70/F10*
70,000 hrs
66,000 hrs
67,000 hrs
54,000 hrs
* F10 includes the degradation B and total failure fraction C
Sø
29
45.5
38.3
Ø31
Ø3
.2
90°
46.6
38.2
31
Lumen
90°
85
170
60°
34.7
7.35
tc/tp
I (cd/klm)
5.6
LUGA Shop 2013 HE HiCRI 5000 lm_GB 2/4 August, 2013
Typical Light Distribution Curve
255
340
30°
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
Please find further detailed information at www.vossloh-schwabe.com.
A Member of the Panasonic Group
Vossloh-Schwabe Deutschland GmbH · Hohe Steinert 8 · 58509 Lüdenscheid · Germany · Phone +49 23 51/10 10 · Fax +49 23 51/10 12 17 · www.vossloh-schwabe.com
2
LUGA Shop 2013 – LED Modules COB for Retail Environments
LUGA Shop 2013 HE HiCRI 5000 lm
Bins
2700K
0.43
3000K
0.42
3090K
3500K
0.41
2910K
2770K
2630K
3390K
3610K
0.40
4000K
0.39
3850K
4150K
0.38
0.37
0.36
0.35
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
Measurement tolerance x/y: ± 0.005
LUGA Shop 2013 HE HiCRI 5000 lm_GB 3/4 August, 2013
Assembly and Safety Information
Installation must be carried out under observation of the relevant regulations and standards. The LED modules are designed for operation within
a casing or luminaire. Installation must be carried out in a voltage-free
state (i.e. disconnection from the mains). The following advice must be
observed; non-observance can result in the destruction of the LED
assembly modules, fire and/or other hazards.
• ESD (electrostatic discharge) protection measures must be observed
when handling and installing the LED modules. See VS's application
notes on ESD protection.
• LED assembly modules must not be subjected to any undue mechanical stress, e. g.:
– do not treat as bulk cargo
– avoid shear and compressive forces during handling and installation
– do not damage circuit paths
– do not touch the yellow phosphorus layer
• The module must be fixed onto a thermally conductive surface with
three M3 screws. A torque of 0.6±0.1 Nm is required.
• Safe operation only possible by the use of external constant current
sources (Imax. see table "Electrical Characteristics").
• Operation only with power supply units that feature the following
protection:
– Short-circuit protection
– Overload protection
– Overheating protection
– SELV equiv. (Safety Extra Low Voltage); U max. £ 60 V
– Imax. (see table "Maximum Ratings") must not be exceeded.
• When operating devices will be selected care has been taken to ensure that the maximum values (see table "Maximum Ratings") will not
be exceeded.
• Please ensure the correct polarity of the leads prior to commissioning.
Reversed polarity can destroy the modules.
• The LED modules are connected via two on-board push-in connectors
for rigid or tinned conductors.
Conductor section:
– tinned: 0.25–0.8 mm²
– rigid: 0.5–0.75 mm²
Strip length: 6.5–8.0 mm
The contacts can be released with a flat-headed screwdriver with a
width of 3 mm.
• Safety regulations acc. to EN 60598 (or further standards) has to be
observed if the maximum output voltage exceed the permitted touchable value.
• Measurement tolerance of luminous flux (see table "Optical Characteristic"): ± 7 % (in addition to production tolerance).
• A parallel or serial connection of the modules is not allowed.
• To ensure problem-free operation, the specified maximum temperature
at the tc point (see "Operating Life") must be observed (and measured in accordance with EN 60598-1). To satisfy this point, it may be
necessary to put measures in place to ensure any heat is dissipated
from the PCB to the environment. For optimized thermal heat transfer,
a thermal conductive graphite foil is available (Ref. No.: 549502).
• In the event of outdoor applications or applications in damp locations, care must be taken to protect LED assembly modules against
humidity, splashes and jets of water. Any corrosion damage resulting
from humidity or contact with condensation will not be recognised as
a defect or manufacturing fault. LED assembly modules are not
specially protected against foreign bodies or dust. Depending on the
type of application, further protection must be ensured to prevent dust
and foreign bodies from entering.
• The photobiological safety of the LED modules must be classified into
risk groups in accordance with EN 62471: 2008.
– general lighting
exempt group:
WU-M-466
– other applications
risk group 1:
WU-M-466
Applied Standards
EN 62031
LED modules for general lighting – Safety specifications
pending
EN 62471
Photobiological safety of lamps and lamp systems
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
Please find further detailed information at www.vossloh-schwabe.com.
A Member of the Panasonic Group
Vossloh-Schwabe Deutschland GmbH · Hohe Steinert 8 · 58509 Lüdenscheid · Germany · Phone +49 23 51/10 10 · Fax +49 23 51/10 12 17 · www.vossloh-schwabe.com
3
LUGA Shop 2013 – LED Modules COB for Retail Environments
Accessories
Thermal conductive graphite tape
Type: Thermal tape 42x40.7 mm Graphite
Thermal resistance: Rth £ 0.04 K/W
Ref. No.: 549502
42
31
29
38,30
2
40,70
R
33,40
Reflectors:
– ACL-Lichttechnik GmbH
www.reflektor.com
– Alux-Luxar GmbH & Co. KG
www.alux.de
– JORDAN REFLEKTOREN GmbH & Co. KG
www.jordan-reflektoren.de
Heat sinks with active cooling:
– AVC
www.avc-europa.de
– Nuventix, Inc.
www.nuventix.com
– Sunon
www.sunon.com
Heat sinks with passive cooling:
– ALPHA-Numerics GmbH
www.alpha-numerics.de
– AVC
www.avc-europa.de
– Fischer Elektronik GmbH & Co.
KG
www.fischerelektronik.de
– Frigo Dynamics
www.frigodynamics.com
LED Constant Current Drivers
Mains voltage: 220 – 240 V ±10%
Mains frequency: 0 Hz, 50 – 60 Hz
SELV-equivalent
5,5
23
75
10
45
64
4,2
(5,5)
99
99
4
33
4,2
123
67
79
111
(13
0)
4,2
LUGA Shop 2013 HE HiCRI 5000 lm_GB 4/4 August, 2013
110
(20)
4,2
(5,5)
30
4,2
5,5
Dimmable constant current drivers
700 mA und 1050 mA – DALI
Type: ECXd 700.017
Current output: 700 mA
Voltage output: 9–48 V
Power: 34 W
Ref. No.: 186177
Type: ECXd 1050.020
Current output: 1050 mA
Voltage output: 20–57 V
Power: 60 W
Ref. No.: 186196
(5,5)
99
5,5
Constant current drivers
700 mA and 1050 mA
Type: ECXe 700.022
Current output: 700 mA
Voltage output: 20–57 V
Power: 40 W
Ref. No.: 186200
Type: ECXe 1050.021
Current output: 1050 mA
Voltage output: 20–57 V
Power: 60 W
Ref. No.: 186198
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
Please find further detailed information at www.vossloh-schwabe.com.
A Member of the Panasonic Group
Vossloh-Schwabe Deutschland GmbH · Hohe Steinert 8 · 58509 Lüdenscheid · Germany · Phone +49 23 51/10 10 · Fax +49 23 51/10 12 17 · www.vossloh-schwabe.com
4