Download A. Simulation of a Parallel Resonance Circuit

Laboratory Procedures
DeVry University
College of Engineering and Information Sciences
I.
OBJECTIVES
1. To simulate the operation of a series and parallel resonance circuit consisting of a resistor
(R), an inductor (L), and a capacitor (C).
2.
To plot the resonance curves of the simulated RLC circuit by varying the AC voltage source.
frequency.
3. To build series and parallel RLC resonance circuit and to verify the results obtained by
simulation.
II.
PARTS LIST
Equipment:
IBM PC or compatible
Function generator
DMM (digital multimeter)
Parts:
1 - 470
Ω resistor
1 - 47 mH inductor
1 - 1 µF capacitor
Software:
MultiSim 11
III.
PROCEDURE
A.
Simulation of a Parallel Resonance Circuit
1. Construct the RLC parallel circuit shown in Figure 1. Simulate the circuit at the frequencies
shown in Table 1. Note and record the current readings obtained in the table with switch S1
closed. This represents the inductor as an ideal inductor with zero wire resistance.
The inductor self-resistance, RL = 65 Ω, has been included in the schematic after measuring
the actual component. If the inductor you choose has different DC resistance, please feel free
to modify the circuit.
2. Plot the data obtained above in the graph sheet below. Note: frequency should be on the Xaxis; the source current IS (mA) should be on Y-axis.
Figure 1: Parallel Resonance Circuit
Frequency, Hz
IS (RMS), mA
IC (RMS), mA
IL (RMS), mA
200
300
500
700
730
734
738
800
1000
1200
1400
Table 1: Parallel Resonance Simulation with Switch S1 “OFF”
Plot 1 – Parallel Resonance Data
3. Answer the questions below:
a)
What happens to the source current, IS, as the frequency is changed from low
to high? Describe in your own words.
Answer:
b)
Did the source current, IS, go through a minimum or maximum as the
frequency is changed from low to high?
Answer:
c)
What is the source frequency at the source current, IS, minimum? What do
you call the frequency at that point?
Answer:
d)
What do you notice from the values of the currents IC and IL at IS minimum?
Answer:
e)
What is the phase relationship between IC and IL at IS minimum?
Answer:
f)
What happens to the total impedance, ZP, of the parallel circuit at the current
minimum? Choose the correct answer below:
Answer:
i)
OPEN Circuit
ii)
SHORT Circuit
g)
Why is the source current, IS, minimum at this frequency?
Answer:
4. Turn the switch J1 in the simulator to the OPEN condition. Vary the source frequency
between 700 Hz to 734 Hz (in steps of 2 Hz) to obtain the minimum source current, IS. Note
it and also record the frequency below.
New resonant frequency with the J1 switch OPEN =
Hz.
5. Answer the questions below with the J1 switch open:
a)
What happened to the inductive branch of the circuit with the switch J1
OPEN?
Answer:
b)
Did the resonance frequency go UP or DOWN compared with the previous
result? Circle the correct answer.
Answer:
c)
Calculate the Quality Factor, Q of the inductor at this resonance frequency.
Q = {ωres L }/ RL
Answer:
B.
Simulation of a Series Resonance Circuit
1. Construct the RLC series resonance circuit shown in Figure 2 in Multisim. Simulate the
circuit at the frequencies shown in Table 2, and record the current readings obtained.
The inductor self-resistance, RL = 65 Ω, has been included in the schematic. If the inductor
you choose has different DC resistance, please feel free to modify the circuit.
Figure 2: Series Resonance Circuit
Frequency, Hz
IS (RMS), mA
VC (RMS), mV
200
300
500
700
730
734
738
800
1000
1200
1400
Table 2: Series Resonance Simulation
VL (RMS), mV
2. Plot the data obtained above in the graph sheet below. Note: frequency should be on
the X-axis; the source current IS (mA) should be on Y-axis.
3. Use the simulation results to answer the following questions:
a)
What happens to the source current, IS, as the frequency is changed from low
to high? Describe in your own words.
Answer:
b)
What is the source frequency at the source current, IS, maximum? What do
you call the frequency at that point?
Answer:
c)
What do you notice from the values of the voltages VC and VL at IS
maximum?
Answer:
d)
What is the phase relationship between VC and VL at IS maximum?
Answer:
e)
What happens to the total impedance, ZS, of the series L and C part of the
circuit at this current maximum? Choose the correct answer below:
Answer:
i)
OPEN Circuit
ii)
SHORT Circuit
f)
Why is the source current, IS, maximum at this frequency?
Answer:
Plot 2 – Series Resonance Data
C. Construction of a Series or Parallel RLC Circuit and Measurement of Circuit
Characteristics
1. Construct the circuit in either Figure 3 or 4.
Important note: You do not need the switch arrangement for the parallel resonance
circuit; The inductor self-resistance, which is an integral part, cannot be isolated as in the
simulator analysis.
DMM
Current
R = 470 Ω
C = 1 µF
f = 300 to 1400 Hz
+
RL = 65 Ω L = 47 mH
IS
VS = 5 VRMS
Function
Gen.
Figure 3 – Parallel Resonance Circuit
C = 1 µF
IS
+
R = 470 Ω
f = 300 to 1400 Hz
VS = 5 VRMS
Function
Gen.
RL = 65 Ω L = 47 mH
DMM
Current
Figure 4 – Series Resonance
2. Set the function generator voltage to 10 V RMS. Use the same value for frequency as used
in the simulator experiment.
3. Vary the source frequency as indicated in the simulation part of the lab exercise. Record the
current readings. Tabulate the results below:
Frequency, Hz
IS (RMS), mA
200
300
500
700
730
734
738
800
1000
1200
1400
Table 3 – Circuit Measurement Results
4. Are the simulated and calculated values the same? ________ (YES or NO)
5. If you answered NO, explain why you think they differ.
IV.
TROUBLESHOOTING
Describe any problems encountered and how those problems were solved.