Download ultrabass bx 200 - Meteoro Amplificadores

Meteoro
ULTRABASS BX 200
BASS CUBE
User’s Guide
ULTRABASS BX 200
Congratulations for having acquired a product Amplifier Meteor.
All our amplifiers are submitted to a careful quality control, where if the details with affection and attention
check all.
Our concern is to leave our satisfied, happy and ready musicians to take music in Brazil and in The World
for front.
The ULTRABASS BX 200 was developed using the highest technology; the entire project was tested step
by step until the end so that although small the ULTRABASS BX 200 also served for small assays and
shows.
The ULTRABASS BX 200 was developed to supply the necessities of the musician whom it needs to play
alive too.
Before binding the equipment look "The Important notes”. If you have suggestions enters in contact with the
Specialist of products.
Visit us on the web www.amplificadoresmeteoro.com.br
Important Notes
Warning!!
-
Please read this instruction manual carefully before switching on.
-
To help to prolong valve and amplifier life is after turning off at the end of a gig, let your amp cool
down before moving it and certainly before putting into the back of the truck on a cold night.
-
If the loudspeaker is disconnected a high voltage can be present at these output terminals.
Operation in this manner can damage your amplifier; therefore ensure that loudspeaker is
properly connected. Remember to set the Impedance Select to the appropriate setting.
-
Do not attempt to remove amplifier chassis; there are no serviceable parts.
-
Never use an amplifier in damp or wet conditions.
-
Always unplug this apparatus during lightning storms or when unused for long periods of time.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and at the point exit from the apparatus.
- Is recommended that audio cables used to connect to your amplifier be of a high quality screened
type. These should not exceed 10 meters in length.
-
Use a damp cloth to wipe the controls on the front & rear chassis panels and all the amplifier.
2
Description of the panel of the ULTRABASS BX200
01 - Hi - Connection /In put for instrument of high impedance where we can bind to basses with passive pick
up and pedals that send a signal not very high
02- Low - Connection /In put for instrument of low impedance (indicated for basses with active pick up or
use with pedals that emits high signals).
03- Gain - This button controls the profit of the daily pay-amplifier.
04- Presets- Selector rotating have that adjusts 05 presets of frequencies
05 - Treble- Button that adjusts the equalizes of trebles for more and for less
06-Ultramid- Button that adjusts the equalizes of medium for more or for less
07-Bass - Button that adjusts the equalizes of low for more and for less
08-Master- Button that adjusts the volume for more or for less.
09-Line out - Exit of balanced line for connection in sound table "mixer".
10-Speaker out - Exit for optional use of a external box.
Back Panel
11- Force - handle of force of the amplifier.
10-Fuse - Compartment where it is the fuse, that has the function to protect the amplifier of some electric
overload.
11-Key of voltage Selector - key for adjustment of voltage in 110 or 220 v.
Binding ULTRABASS BX200
An important tip before binding ULTRABASS BX 200: It starts with the volume in the 2 and goes adding to
volume the measure that you will be knowing the amplifier.
To start it verifies the voltage (110 or 220v), in case that necessary it has adjusted the voltage in the key in
the back panel, connects the handle of force in the taking, binds the Power key. Now it is alone to increase
the volume with calm, places the controls of equalizes (Gain, Treble, Ultramid, Bass and Master) in the way,
in accordance with goes regulating its necessities to arrive in the desired seals. The amplifiers Meteor are
very sensible to put this you go to perceive that when moving in the equalizes it will go to feel great
differences in the seals of its amplifier.
To facilitate, I prepared some tips that go to serve of reference in this first contact.
ULTRABASS BX200
Gain
12345
Treble
Ultra Mid
Bass
Master
Presets
This configuration serves so that it can feel each frequency of the equipment. Through this regulation,
it turns the button of "presets" so that it perceives all infinity of possible seals.
PS: The levels of profit and the frequencies can have variations depending on an instrument for the
other.
3
Solutions of problems
The Amplifier Not League?
-
The amplifier is on in the taking?
The key in the back panel is in the certain voltage (110/220v)?
It is not leaving sound the amplifier?
-
The adjustment of the Volume is not low, has adjusted the volume.
He verifies if its handle is in perfect conditions of use.
All equalizes (buttons of Gain, Treble, Ultramid, Bass and Master) is opened?
The amplifier is distorting when I touch.
- It verifies if it plug the bass in the certain entrance: "Hi" for basses with active capitation and "Low" for
basses with passive capitation.
The sound is with noise.
-
Verifies if the electric net this working in the correct tension.
He verifies if the used handle is not damaged or is inadequate.
The used taking is not possessed entered of three bolts, uses rulers or adapters not to remove the bolt of
the land that is in the equipment.
When using adapters of 2 bolts and the same presenting noise, invert the adapter of position in the
taking.
Technical Specs
- Connection /In put for Bass with sensitivity of 100mv (High Impedance)"Hi" and "Low"
(Low Impedance)
- Power: 250 watts RMS
- Speaker of 15"
- Electric Piezo.
- Exit of Balanced line (For connection in table of sound "Mixer")
- Exit for external box
- Weight: 27,5Kg
- Dimensions: 540x470x390mm
4