* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Table 6.2 2N3906 PNP Transistor
Survey
Document related concepts
Resistive opto-isolator wikipedia , lookup
Voltage optimisation wikipedia , lookup
Stray voltage wikipedia , lookup
Electrical ballast wikipedia , lookup
Peak programme meter wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Thermal runaway wikipedia , lookup
Alternating current wikipedia , lookup
Mains electricity wikipedia , lookup
Rectiverter wikipedia , lookup
Buck converter wikipedia , lookup
Opto-isolator wikipedia , lookup
Current source wikipedia , lookup
Two-port network wikipedia , lookup
Current mirror wikipedia , lookup
Transcript
Electronic I (DMT 121) Laboratory Module Exp. 5 EXPERIMENT 5 Current and Voltage Characteristics of BJT 1. OBJECTIVE: 1.1 1.2 1.3 2. To practice how to test NPN and PNP transistors using a multimeter. To demonstrate the relationship between collector current (I C) and base current (IB). To provide the opportunity for plotting the output characteristic curves for a transistor using measured component values. INTRODUCTION: PART A : Testing Transistor Diode Junction Basically, a bipolar (BJT) transistor can be represented internally by two diode or p-n junctions. Consequently, a multimeter can be used to check each diode junction, as was done in Experiment 2. If we know the three terminals, then it is possible to determine if a given transistor is NPN or PNP bipolar transistor. Figure 6.1 Schematic diagram of circuit PART B : Current and Voltage Characteristics of BJT The ratio of the dc collector current ( IC) to the dc base current (IB) is the dc beta () which is the dc current gain of transistor is β= IC IB (6.1) The voltage across R1 can be calculated by Ohm’s Law V1 = IBR1 (6.2) Where IB is dc base current. -1- Electronic I (DMT 121) 3. Laboratory Module Exp. 5 COMPONENT AND EQUIPMENT: PART A : Testing Transistor Diode Junction 3.1 3.2 3.3 3.4 2N3904 NPN transistor 2N3906 PNP transistor Multimeter Breadboard PART B : Current and Voltage Characteristics of BJT 3.1 3.2 3.3 3.4 3.5 4. 100 kΩ resistor 2N3904 NPN transistor Two dc power supply Two multimeter Breadboard, wires PROCEDURE: PART A : Testing Transistor Diode Junction 4.1 Measuring Voltage across 2N3904 NPN transistor junction: 4.1.1 The schematic diagram and diode junction represented are shown in Figure 6.2. Figure 6.2 4.1.2 4.1.3 Pin configurations of 2N3904 transistors Take your multimeter and select a low-resistance meter range. Connect the meter’s positive lead to the transistor’s base lead, with the meter’s negative lead connected to the transistor’s emitter lead. (NOTE: You have forward biased the transistor’s base-emitter diodes junction.) 4.1.4 4.1.5 Record the display reading in Table 6.1. Now, reverse the meter’s leads so that the positive lead is connected to the emitter and the negative lead is connected to the base. 4.1.6 Record the display reading in Table 6.1. 4.1.7 Then, connect the meter’s positive lead to the base and the negative lead to the transistor’s collector lead. 4.1.8 Record your result in Table 6.1. 4.1.9 After that, reverse the meter’s leads so that the positive lead is connected to the collector and the negative lead is connected to the base. 4.1.10 Record the result in Table 6.1. -2- Electronic I (DMT 121) Laboratory Module Exp. 5 4.1.11 Now connect the meter’s positive lead to the collector the negative lead to the transistor’s emitter lead. 4.1.12 Note and record this value in Table 6.1. 4.1.13 Then, reverse the meter’s leads so that the positive lead is connected to the emitter and the negative lead is connected to the collector. 4.1.14 Record this value inTable 6.1. (NOTE: If transistor diode junction was forward biased, you should have obtained a value between 0.5 and 0.8 and if the transistor diode junction was reverse biased, the transistor would be in an “open-circuit” condition). 4.2 Measuring Voltage across 2N3906 PNP transistor junction: 4.2.1 The schematic diagram and diode junction represented are shown in Figure 6.3. Figure 6.3 4.2.3 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 4.2.10 4.2.11 4.2.12 4.2.13 4.2.14 4.3 Pin configurations of 2N3906 transistors Take your multimeter and select a low-resistance meter range. Now, connect the meter’s positive lead to the transistor’s base lead and the negative lead to the transistor’s emitter lead. Record your result in Table 6.2. Then, reverse the meter’s leads so that the positive lead is connected to the emitter and negative lead is connected to the base. Note the meter reading, and record the result in Table 6.2. Then connect the meter’s positive lead to the base and the negative lead to the transistor’s collector lead. Record your result in Table 6.2. After that, reverse the meter’s leads so that the positive lead is connected to the collector and the negative lead is connected to the base. Record the result in Table 6.2. Now, connect the meter’s positive lead to the collector and the negative lead to the transistor’s emitter lead. Note the meter reading, and record this result in Table 6.2. After that, reverse the meter’s leads so that the positive lead is connected to the emitter and the negative lead is connected to the collector. Note the meter reading, and record this result in Table 6.2. Compare the result of Table 6.1 and Table 6.2.Write your observations. -3- Electronic I (DMT 121) Laboratory Module Exp. 5 PART B : Current and Voltage Characteristics of BJT 4.1 Measure and record the actual resistance of your 100 kΩ resistor. IC V1 B 100 kΩ C VCE VCC E VBB Figure 6.4 4.2 Construct the circuit shown in Figure 6.4. Both supply voltages should initially be set to 0 VDC. 4.3 Calculate the value of V1 that is required to generate a current of 5 µA through R1. 4.4 Adjust VBB to obtain the value of V1 calculated in Step 4.3. 4.5 Adjust VCC so that VCE is 0.5 VDC. 4.6 Measure and record the value of IC in appropriate space in Table 6.3. 4.7 Increase VCC to provide a VCE of 1 VDC. Measure and record the corresponding value of IC in Table 6.3. 4.8 Repeat step 4.7 for each of the values of VCE listed in Table 6.3. 4.9 After completing the measurements in step 4.8 for IB = 5 µA, return VCE to 0 VDC. Calculate the value of V1 that is required to generate a current of 10 µA through R 1. Adjust VBB to provide this value of V1. 4.10 Repeat steps 4.5 through 8 for IB = 10 µA. 4.11 Repeat steps 4.5 through 4.10 until Table 6.3 is complete. 4.12 Using the data recorded in Table 6.3, plot the characteristic collector curves for the 2N3904 in graph paper. -4- Electronic I (DMT 121) Name Laboratory Module Exp. 5 :_________________________________ Course :_________________________________ 5. Matrix No : _________________ Date : _________________ RESULTS: PART A : Testing Transistor Diode Junction Table 6.1 2N3904 NPN Transistor Meter Leads Step Number Result + - 4.1.4 Base Emitter 4.1.5 Emitter Base 4.1.7 Base Collector 4.1.9 Collector Base 4.1.11 Collector Emitter 4.1.13 Emitter Collector Table 6.2 2N3906 PNP Transistor Meter Leads Step Number Result + - 4.2.3 Base Emitter 4.2.5 Emitter Base 4.2.7 Base Collector 4.2.9 Collector Base 4.2.11 Collector Emitter 4.2.13 Emitter Collector Instructor Approval : ____________________ -5- Date : _____________ Electronic I (DMT 121) Laboratory Module Exp. 5 PART B : Current and Voltage Characteristics of BJT (1) For Step 4.1 : The value of R1 : ________________ Ω (2) For Step 4.3 : The value of V1 : _______________ V Table 6.3 VCE (Vdc) IB (µA) +0.5 +1 +5 +10 +15 5 10 20 30 40 50 Instructor Approval : ____________________ -6- Date : _____________ +20 Electronic I (DMT 121) 6. CALCULATIONS: 7. DISCUSSION Laboratory Module Exp. 5 PART A : Testing Transistor Diode Junction 2.6V 0.7V (a) (b) 2.6V (c) 0.7V (d) Figure 6.5 Again, a student used Digital Multimeter (DMM) to test the transistor as shown in Figure 6.6. From the testing, what type of the BJT transistor? -7- Electronic I (DMT 121) Laboratory Module Exp. 5 PART B : Current and Voltage Characteristics of BJT Using the characteristic curves, predict the values of IC for each of the IB and VCE combinations listed below. 8. IC = _________________ when IB = 25 µA and VCE = 10 Vdc IC = _________________ when I B = 35 µA and VCE = 8 Vdc CONCLUSION: -8-