Download CMD234C4 - Custom MMIC

CMD234C4 - Preliminary
DC-18 GHz SP3T Non-reflective Switch
Features
Functional Block Diagram
► Low loss broadband performance
► High isolation
► Non-reflective design
► Integrated 2:4 TTL decoder
► Pb-free RoHs compliant 4x4 SMT package
Description
The CMD234C4 is a broadband MMIC
SP3T switch housed in a leadless 4x4 mm
surface mount package. The CMD234C4
covers DC to 18 GHz and offers a low
insertion loss of 2 dB and high isolation of
40 dB at 10 GHz. The switch also includes
an on board binary decoder circuit which
reduces the number of required logic control
lines from three to two. The CMD234C4
operates using complementary control
voltage logic lines of 0/-5 V and consumes
little DC current.
Electrical Performance - Vctl = 0/-5 V, Vss = -5 V, TA = 25 oC, F = 10 GHz
Parameter
Min
Frequency Range
Typ
Max
Units
DC - 18
GHz
Insertion Loss
2
dB
Isolation
40
dB
Return Loss - On State
9
dB
Return Loss RF1, RF2, RF3, RF4 - Off State
8
dB
Input P1dB
21
dBm
Switching Speed
66
ns
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Specifications
Absolute Maximum Ratings
Parameter
RF Input Power
TTL/CMOS Control Voltages
Rating
State
Bias Condition
+27 dBm
Low
-1V to 0V @ 0.5 mA Typ
-7V
High
-7V to -3V @ 1 uA Typ
Bias Voltage (Vss)
Control Voltage Range (A,B) +0.5V to -7.5V
Channel Temperature, Tch
Truth Table
150 °C
Operating Temperature
-40 to 85 °C
Storage Temperature
-55 to 150 °C
Control Input
Operation of this device outside the maximum
ratings may cause permanent damage.
Bias Voltage & Current
Signal Path State
A
B
RFC to:
High
Low
RF1
Low
High
RF2
High
High
RF3
Vss Range = -5.0V ± 10%
Vss (V)
Iss (Typ) (mA)
Iss (Max) (mA)
-5
4.5
8.0
Electrical Specifications - Vctl = 0/-5 V, Vss = -5 V TA = 25 oC
Parameter
Min
Frequency Range
Typ
Max
Min
Typ
Max
Min
Typ
Max Units
DC - 6
DC - 14
DC - 20
GHz
Insertion Loss
1.7
2
3.4
dB
Isolation
44
37
30
dB
Return Loss - On State
12
9
9
dB
Return Loss - Off State
10
8
8
dB
19.5
21
22
dBm
Input IP3
28
30
30
dBm
Switching Speed
66
66
66
ns
Input P1dB
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Typical Performance
Insertion Loss
0
-1
-2
Insertion Loss/dB
-3
-4
-5
-6
-7
-8
-9
-10
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
13
14
15
16
17
18
19
20
Frequency/GHz
Return Loss
0
RFC
RF1,2,3 On
RF1,2,3 Off
Return Loss/dB
-5
-10
-15
-20
0
1
2
3
4
5
6
7
8
9
10
11
12
Frequency/GHz
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Typical Performance
Isolation Between Ports RFC and RF1/RF2/RF3
0
-10
-20
Isolation/dB
-30
-40
-50
-60
-70
-80
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Frequency/GHz
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Mechanical Information
Package Information and Dimensions
Recommended PCB Land Pattern
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Pin Description
Pin Diagram
Functional Description
Pin
Function
Description
1,5,6,10,11,13,
17,18
N/C
No connection required. These pins may
be connected to RF/DC ground
2,4,7,9,12,
19,21,22,24
and die paddle
Ground
Connect to RF / DC ground
3,8,20,23
RFC, RF3,
RF2, RF1
These pins are DC coupled and matched to
50 Ohm. Blocking capacitors are required
if RF line potential is not equal to 0V
14
Vss
Power supply voltage
15
CTLB
See truth table and control voltage table
16
CTLA
See truth table and control voltage table
Schematic
GND
A, B
Vss
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com
CMD234C4
DC-18 GHz SP3T Non-reflective Switch
Applications Information
Evaluation Board
The circuit board shown has been developed for optimized assembly at Custom MMIC. A sufficient
number of via holes should be used to connect the top and bottom ground planes. As surface mount
processes vary, careful process development is recommended.
Bill of Material
Designator
Value
Description
J1 - J3, J5
SMA End Launch Connector
P1
6 Pin Header
C1
0.33 µF
Capacitor, Tantalum
C2
1000 pF
Capacitor, 0603
C3
100 pF
Capacitor, 0402
U1
CMD234C4 SP3T Switch
PCB
100795 Evaluation PCB
GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions
should be observed during handling, assembly and test.
Custom MMIC
300 Apollo Drive Chelmsford, MA 01824 Phone (978) 467-4290 Fax (978) 467-4294
Visit us online at www.custommmic.com