Download No Slide Title

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Boundary layer wikipedia , lookup

Transcript
1. A clean single crystal silicon (Si) wafer which is doped
n-type (ColumnV elements of the periodic table). MOS
devices are typically fabricated on a <100>, in the X-cut
direction to minimize surface state charges.
2. A 2” diameter clean single crystal silicon (Si) wafer
which represents a single molecule having a diamond
lattice structure. The wafer-flat is used for alignment.
3. A silicon-dioxide (SiO2) layer thermally grown in a
furnace at 1000 oC in a dry oxygen atmosphere.
Throughout the process, SiO2 is used as a mask, as a
dielectric, and for passivation of the wafers surface. The
ability to grow this dense, homogeneous, native-grown
oxide is critical to IC fabrication technology.
4. A thermally grown SiO2 layer on a Si wafer. The SiO2 is
transparent; the color comes from light-interference from
reflection at the Si-SiO2 interface and the SiO2-air interface.
5. Photoresist is spun onto the wafer at 3500 rpm for 30
seconds. The wafer is soft-baked at 90 oC for 30 minutes;
leaving a thin, photo-sensitive film. The film is sensitive
to ultraviolet (UV) light; this is why fabrication
laboratories are often lit by UV-absent, yellow light.
6. A mask is used to protect areas and the photoresist is
exposed to an ultraviolet lamp which exposes the
photoresist for the required pattern.
7. After exposure, the photoresist is developed and then
hard baked at 110 oC for 30 minutes; leaving the desired
image in the film which is used as a mask for etching of
the silicon dioxide layer.
Photoresist layer
Wafer
SiO2 layer
8. The wafer is placed in a buffered hydrofluoric (HF)
etch solution and the silicon dioxide is selectively etched;
leaving the desired pattern in the silicon dioxide. This
basic photolithographic process is repeatedly used to open
windows for selective processing at the silicon surface.
SiO2 layer
Wafer
9. Photoresist is removed leaving a window to the silicon
surface for introduction of controlled dopants, or for metal
contact. The depression obtained in the SiO2 layer is also
used for alignment from level-to-level in the process.
10. Dopant impurities are introduced by accelerating ions
of the desired atoms, such as boron, into the silicon
surface. The SiO2 acts as a mask to protect some silicon
areas from the ion implantation.
11. The boron “dopants” are diffused in a high
temperature furnace and a silicon oxide layer is re-grown
for subsequent processing and passivation. The boron
changes the layer from n-type to p-type material.
12. A full patterned 2” wafer after etching a SiO2 layer,
introducing p-type dopants (Column IV elements) in the
etched windows, and re-growing a second SiO2 layer.
p-well
n-type
Si wafer
13. The oxide is removed or “stripped leaving the diffused
layer and a sub-micron depression which can be seen
under a microscope for alignment of subsequent masks.
14. A SiO2 layer is grown, then a silicon nitride (SiN)
layer is deposited, and finally a SiO2 layer is grown. The
oxide-nitride “sandwich” level is used for masking to
define a channel region which is used to isolate transistors
from each other.
15. A buffered HF etch removes the exposed SiO2. The
SiN masks and protects the underlying SiO2 and Si
surface. The wafer is then ion implanted with boron
atoms to define the channel stop areas.
16. The boron “dopants” are diffused in a high
temperature furnace and a silicon oxide layer is re-grown
on the Si for subsequent processing and passivation. The
SiN area does not easily grow an SiO2 layer; this provides
a selective oxidation process.
17. A SiO2 layer is re-grown, then a poly crystalline
silicon (poly-Si) layer is deposited, and finally a SiO2
layer is grown. The oxide poly-Si “sandwich” level is
used for masking to define the MOS source, drain and
gate regions. The thin, lower-level oxide will be used for
the gate dielectric.
18. The SiO2 is etched leaving the poly-Si gate and open
windows for the source and drain. The poly-Si gate,
source and drain are all highly doped (n+-type) at the
same time; creating a self-aligned MOS process.
19. A SiO2 layer is re-grown over the entire wafer and the
MOS transistor. At this point the NMOS transistor is
defined and only the via-holes and final metal
interconnections are required. Note the SiO2 layers are
used for masking, for the gate dielectric and for
passivation of the surface.
20. A finished 2” wafer containing NMOS transistors,
diodes, and resistors. These IC building blocks were
fabricated by students at UCF’s microelectronic facility.
21. Final Complimentary Metal Oxide Semiconductor
(CMOS) Transistor. Device consists of a NMOS and a
PMOS transistor forming a simple inverter circuit.
22. NMOS drain-source IDS-VDS curves with varying
applied gate voltage. Threshold voltage is approximately
–0.3 volts.