Download Power Point Ch8

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Resistive opto-isolator wikipedia , lookup

Buck converter wikipedia , lookup

Opto-isolator wikipedia , lookup

Current source wikipedia , lookup

Alternating current wikipedia , lookup

Stray voltage wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Transistor wikipedia , lookup

Voltage optimisation wikipedia , lookup

Electronic paper wikipedia , lookup

Mains electricity wikipedia , lookup

P–n diode wikipedia , lookup

Transcript
MALVINO & BATES
Electronic
PRINCIPLES
SEVENTH EDITION
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Chapter
Transistor Biasing
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
8
Topics Covered in Chapter 8
•
•
•
•
•
•
•
Voltage-divider bias
Accurate VDB analysis
VDB load line and Q point
Two-supply emitter bias
Other types of bias
Troubleshooting
PNP transistors
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Voltage divider bias
• Base circuit contains a voltage divider
• Most widely used
• Known as VDB
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Voltage divider bias circuit
+VCC
R1
RC
R1 and R2 form
a voltage divider
R2
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
+VCC
Divider analysis:
R1
VBB =
R2
R1 + R2
VCC
ASSUMPTION: The base
current is normally much
smaller than the divider current.
+VBB
R2
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Now the circuit can be viewed this way:
+VCC
To complete the analysis:
IE =
VBB - VBE
RC
RE
IC @ IE
VC = VCC - ICRC
VCE = VC - VE
VBB
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
The six-step process
1. Calculate the base voltage using the
voltage divider equation.
2. Subtract 0.7 V to get the emitter voltage.
3. Divide by emitter resistance to get the
emitter current.
4. Determine the drop across the collector
resistor.
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
The six-step process
(Continued)
5. Calculate the collector voltage by
subtracting the voltage across the
collector resistor from VCC.
6. Calculate the collector-emitter voltage by
subtracting the emitter voltage from the
collector voltage.
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
VDB analysis
• The base current must be much smaller
than current through the divider
• With the base voltage constant, the
circuit produces a stable Q point under
varying operational conditions
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Is the divider a stiff source?
+VCC
R1
RC
Find the Thevenin
resistance.
RTH = R1 R2
R2
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
A Thevenin model of the bias circuit:
+VCC
RC
RTH
VBB
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
The 100:1 rule applied to the bias circuit:
+VCC
RTH < 0.01 RIN
RC
RTH
RIN
VBB
When this rule is met,
the divider is stiff.
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
Firm voltage divider
• Used because divider resistors (e.g. R1
and R2) in a stiff design would be too
small
• The collector current will be about 10%
lower than the stiff value
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Sometimes a firm divider is chosen. +VCC
R1 R2 < 0.1 bdcRE
R1
RC
A closer approximation:
VBB - VBE
IE =
R1 R2
RE +
bdc
R2
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
VDB load line and Q point
• VDB is derived from emitter bias
• The Q point is immune to changes in
current gain
• The Q point is moved by varying the
emitter resistor
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Two-supply stiff emitter bias:
IE =
VEE - 0.7 V
10 V
3.6 kW
RE
Assume 0 V
2.7 kW
IE =
2 V - 0.7 V
= 1.3 mA
1 kW
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
1 kW
2V
Find the voltages:
10 V
3.6 kW
VC = 10 V - (1.3 mA)(3.6 kW) = 5.32 V
VCE = 5.32 V - (-0.7 V) = 6.02 V
2.7 kW
1 kW
2V
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
+VCC
Base bias:
RB
•The least predictable
•Q point moves with replacement
•Q point moves with temperature
•Not practical
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
+VCC
Emitter-feedback bias:
RB
•Better than base bias
•Q point still moves
•Not popular
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
RE
+VCC
Collector-feedback bias:
RB
•Better than emitter-feedback bias
•Q point still moves
•Some applications because of circuit
simplicity
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
+VCC
Collector- and emitter
-feedback bias:
RB
•Better than emitter-feedback bias
•Not as good as voltage-divider bias
•Limited application
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
RE
Two-supply emitter bias:
•Very stable
•Requires 2 supplies
Note: Also called TSEB
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
+VCC
Voltage divider bias:
R1
•Very stable
•Requires 1 supply
•The most popular
R2
Note: Also called VDB
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
RE
Troubleshooting
• Voltage measurements
• Use 10 MΩ input voltmeter
• Troubles include:
Opens
Shorts
Faulty transistors
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
PNP transistor
• The base is n-type material
• The collector and emitter are p-type
material
• The emitter arrow points in
• Can be used with a negative power
supply
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
PNP transistor symbol
and current flow
IC
IB
IC
IB
IE
Electron flow
IE
Conventional flow
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
-VCC
PNP Biasing with a
negative supply
R1
R2
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RC
RE
+VEE
PNP Biasing with a
positive supply
R2
R1
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
RE
RC