Download Data and Computer Communications

Data and Computer
Communications
Chapter 3 – Data Transmission
Ninth Edition
by William Stallings
Data and Computer Communications, Ninth
Edition by William Stallings, (c) Pearson
Education - Prentice Hall, 2011
Data Transmission
What we've got here is failure to communicate.
Paul Newman in Cool Hand
Luke
Data Transmission
The successful
transmission of
data depends on
two factors:
1)
quality of the signal
being transmitted
(garbage in, garbage out)
2)
characteristics of the
transmission
medium
Transmission Terminology
Transmission Terminology
Data transmission occurs between transmitter
and receiver over some transmission medium.
Communication
is in the form of
electromagnetic
waves.
Guided
media
twisted pair,
coaxial cable,
optical fiber
Unguided
media
(wireless)
air, vacuum,
seawater
Transmission Terminology
Transmission Terminology
 Simplex

signals transmitted in one direction
• eg. Television
 Half

duplex
both stations transmit, but only one at a time
• eg. police radio
 Full

duplex
simultaneous transmissions
• eg. telephone
Frequency, Spectrum and
Bandwidth
Time Domain Concepts
 analog signal
• signal intensity varies smoothly with no breaks
 digital signal
• signal intensity maintains a constant level and
then abruptly changes to another level
 periodic signal
• signal pattern repeats over time
 aperiodic signal
• pattern not repeated over time
Analog and Digital Signals
Periodic
Signals
Sine Wave
(periodic continuous signal)

peak amplitude (“A” in the previous slide)



frequency (f)





maximum strength of signal
typically measured in volts
rate at which the signal repeats
Hertz (Hz) or cycles per second
period (T) is the amount of time for one repetition
T = 1/f
phase ()

relative position in time within a single period of signal
Varying Sine Waves
s(t) = A sin(2ft +)
Wavelength ()
the wavelength of
a signal is the
distance occupied
by a single cycle
can also be stated as the
distance between two
points of corresponding
phase of two consecutive
cycles
especially when v=c
assuming signal
velocity v, then the
wavelength is related
to the period as  = vT
or
equivalently
f = v
• c = 3*108 ms-1 (speed of light
in free space)
• For copper: v=0.55c to 0.77c
Frequency Domain Concepts
 signals
are made up of many frequencies
 components are sine waves
 Fourier analysis can show that any signal
is made up of components at various
frequencies, in which each component is a
sinusoid
 can plot frequency domain functions
Addition of
Frequency
Components
(T=1/f)
(c) is the sum of f & 3f

http://www.falstad.com/f
ourier/
Frequency
Domain
Representations

frequency domain
function of Fig 3.4c
(previous slide)

frequency domain
function of single
square pulse
Spectrum & Bandwidth
Signal with dc Component
Data Rate and Bandwidth
any transmission
system has a
limited band of
frequencies
limiting
bandwidth
creates
distortions
this limits the data
rate that can be
carried on the
transmission medium
most energy in
first few
components
square waves
have infinite
components and
hence an infinite
bandwidth
If only two frequencies get through the transmission system,
the wave form shown in the previous slide would be received.
There is a direct relationship between data rate and bandwidth.
Analog and Digital Data
Transmission
 data

entities that convey information
 signals

electric or electromagnetic representations of
data
 transmission

communication of data by propagation and
processing of signals
Acoustic Spectrum (Analog)
-> définition du décibel
Analog and Digital
Transmission
(1080i vs 1080p : http://www.pcmag.com/article2/0,2817,2413044,00.asp)
(Digital Data)
Examples:
IRA (International
reference
alphabet)
Text
Character strings
Advantages & Disadvantages
of Digital Signals
Audio Signals

frequency range of typical speech is 100Hz-7kHz
 easily converted into electromagnetic signals
 varying volume converted to varying voltage
 can limit frequency range for voice channel to
300-3400Hz

Video
Signals
to produce a video signal a TV
camera is used
 USA standard is 483 lines per
frame, at a rate of 30 complete
frames per second


actual standard is 525 lines but 42 lost during
vertical retrace
horizontal scanning frequency is
525 lines x 30 scans = 15750 lines
per second (63.5 μs per line but 11 μs is
lost during horizontal retrace -> 52.5 μs )

max frequency reached if line
alternates black and white (450
columns)

max frequency of 4.2MHz (450/2
cycles in 52.5 μs)
Video
Signals

http://en.wikipedia.org/wiki/1080p

2.1 megapixels X frame rate

1 pixel needs 3 X 8 bits = 24 bits




24 fps => 2.1 X 24 X 24 Mbits/s
50 fps => 2.1 X 24 X 50 Mbits/s
60 fps => 2.1 X 24 X 60 Mbits/s
Compression techniques are often used.
Analog Signals
Modulator/demodulator
Digital Signals
Similar to modem
but for voice signal
Coder/decoder
Transmitter/receiver
(Analog and
Digital
Transmission)
Transmission Impairments
 signal
received may differ from signal
transmitted causing:


In analog systems -> degradation of signal quality
In digital systems-> bit errors
 most


significant impairments are
attenuation
attenuation distortion (some freq. are
more attenuated than others)

delay distortion (velocity of waves depends
on their frequencies)

noise
ATTENUATION
 signal strength falls off with distance over any
transmission medium
 varies with frequency
Equalize
attenuation across
the band of
frequencies used
by using loading
coils or amplifiers.
Received signal
strength must be:
•strong enough to be
detected
•sufficiently higher than
noise to be received
without error
Strength can be
increased using
amplifiers or
repeaters.
Attenuation Distortion
Delay Distortion
 occurs
because propagation velocity of a
signal through a guided medium varies
with frequency
 various frequency components arrive at
different times resulting in phase shifts
between the frequencies
 particularly critical for digital data since
parts of one bit spill over into others
causing intersymbol interference
Delay Distortion
Noise
unwanted signals
inserted between
transmitter and
receiver
=> is the major
limiting factor in
communications
system performance
Categories of Noise
Intermodulation noise
• produced by nonlinearities in the
transmitter, receiver, and/or
intervening transmission medium
• effect is to produce signals at a
frequency that is the sum or
difference of the two original
frequencies (sosmat.com)
Categories of Noise
Crosstalk:


Impulse Noise:




caused by external
electromagnetic interferences
noncontinuous, consisting of
irregular pulses or spikes
short duration and high
amplitude
minor annoyance for analog
signals but a major source of
error in digital data
a signal from one line is
picked up by another
can occur by electrical
coupling between nearby
twisted pairs or when
microwave antennas pick
up unwanted signals
Channel Capacity
Maximum rate at which data can be transmitted over a
given communication channel under given conditions
Channel characteristics :
bandwidth
data rate
noise
error rate
in cycles
average
rate of
in bits per
per
noise level corrupted
second
second or
over path
bits
Hertz
main
limitations constraint
due to
on
physical
achieving
properties efficiency
is noise
Nyquist Bandwidth
In the case of a channel that is noise free:
 if rate of signal transmission is 2B then can carry
signal with frequencies no greater than B

given bandwidth B, highest signal rate is 2B

for binary signals, 2B bps needs bandwidth B Hz
 can increase rate by using M signal levels
 Nyquist Formula is: C = 2B log2M
 data rate can be increased by increasing M


however this increases burden on receiver
noise & other impairments limit the value of M
Shannon Capacity Formula

considering the relation of data rate, noise and
error rate:


faster data rate shortens each bit so bursts of noise
corrupts more bits
given noise level, higher rates mean higher errors

Shannon developed formula relating these to the
signal-to-noise ratio -> SNR= (signal power) / (noise power)
 capacity C = B log2(1+SNR) (ex. SNR=0 -> C=0)


theoretical maximum capacity
get much lower rates in practice
 SNRdb=10
log10 (SNR)
Summary
 transmission

concepts and terminology
guided/unguided media
 frequency,
spectrum and bandwidth
 analog vs. digital signals
 data rate and bandwidth relationship
 transmission impairments

attenuation/delay distortion/noise
 channel

capacity
Nyquist/Shannon