Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
G1033-035, 1550 nm GPON Laser Diode Chip DATASHEET | FEBRUARY 2016 FIBER OPTICS EMCORE's G1033-035, 1550 nm GPON distributed feedback DFB laser chip is designed to provide the source laser for the uncooled PON applications. Performance Highlights Parameter Min Typical Max Units 1530 1550 1570 nm Operating Temperature Range 0 +25 +85 C Optical Output Power - - 50 mW 30 40 - dB Wavelength Side Mode Suppression Ratio (SMSR) Applications Uncooled PON Applications FTTx Networks Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated for extended periods of time may effect device reliability. Features Advanced Digital Chip Design Wide Operating Temperature Range: -40 to +85C Telcordia Technologies™ 468 Compliant RoHS Compliant Parameter Symbol Operating Temperature Range Top Storage Temperature Range TSTG Optical Output Power Po Laser Reverse Voltage Continuous Operating Current ESD Susceptibility1 Condition - Min Max Unit 0 +85 °C -40 +100 °C Continuous - 50 mW Vr Continuous - 1 V Iop Continuous - 200 mA - - - 500 V Continuous 1 Based on human-body model of R = 1500 Ohm and C = 100 pF. In general, ESD precautions should be taken to avoid damage to the device | REV 2016.02 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. G1033-035, 1550 nm GPON Laser Diode Chip DATASHEET | FEBRUARY 2016 FIBER OPTICS Chip Electrical/Optical Performance Characteristics Parameter Symbol Condition Min Typ Max Unit Operating Temperature Top - 0 +25 +85 C Threshold Current ITH +25C +85C - 9 28 20 45 mA Slope Efficiency QE +25C +85C 0.30 0.20 0.36 - mW/mA +25C - - 4.5 12 VOP - 1.3 1.5 V nm DC Resistance R Operating Voltage At Ith+20mA 1530 1550 1570 SMSR - 30 40 - dB - Full Width, Half Max - 32 36 deg Beam Divergence Angle, Horizontal - Full Width, Half Max - 27 30 deg Laser Reverse Voltage Vr - 1 - - V Iop +25C - - 100 mA Central Wavelength 1 Side Mode Suppression Ratio Beam Divergence Angle, Vertical Laser Operating Current2 1 Unless otherwise specified 2 DC Outline Drawing Figure 1: Drawing of 1490 nm DFB laser diode chip. Top view and cross-sectional views are shown. | REV 2016.02 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. G1033-035, 1550 nm GPON Laser Diode Chip DATASHEET | FEBRUARY 2016 FIBER OPTICS Ordering Information Part Number: G1033-035 Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. This device has been classified with the FDA/CDRH under accession number 0220309. All Versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007/EN 60825-1:2007 Single-mode fiber pigtail with SC/APC connectors (standard). Wavelength = 1.5 m. Maximum power = 30 mW. Because of size constraints, laser safety labeling (including an FDA class 1M label) is not affixed to the module, but attached to the outside of the shipping carton. Product is not shipped with power supply. Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. | REV 2016.02 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.