Download EF NI H K Test results of the Prototype Outer Tracker Front

Test results of the Prototype Outer Tracker
Front-End Box
Ad Berkien
Tom Sluijk
Albert Zwart
NIKH EF
Proto Outer Tracker Front-End Tests
1
27/01/2004 az
GOL-AUX Board
•
Four OTIS boards connected to the GOL-AUX board (R190-R192 removed).
Oscillations observed on the supply voltages:
– Tantal Elco’s 100uF added on the power inputs and on the output of the negative
regulator.
•
Clock distribution is bad, BX- counter in OTIS are not equal
– LVDS repeater (SN65LVDS108) mounted and connected to the OTIS connectors
•
Settings:
– Module location address switch = 1
• I2C addresses 0x8 - 0xC
– I2C pull-up 1K to 2.5V
– Seldiv (J101) must be 1 >> GOL ready
NIKH EF
Proto Outer Tracker Front-End Tests
2
27/01/2004 az
OTIS Boards
•
•
Terminators (120 ohm) installed on clock vias and covered with epoxy
Board manufacturer error; the inner layers are not 100u as requested
– To much voltage drop over the integrated coil for the digital VDD of the OTIS, new
coil mounted.
– Less heat spreading and conduction in the board.
•
•
•
•
I2C clamp diodes removed, did not work as on the testboards( not understood)
-3V power connection to the ASDBLR board has to much coupling to the
digital VDD of the OTIS, noisy ASDBLR –3V power.
+3V for the ASDBLR is also used for the LVDS receivers for the data to the
GOL this makes a noisy ASDBLR +3V power.
Cut in the ground plane under the coils gives an 10% increase of the
inductance.
NIKH EF
Proto Outer Tracker Front-End Tests
3
27/01/2004 az
ASDBLR Boards
•
ASDBLR changed; the high level discriminator cannot be disabled anymore
– Change in the output resistors.
•
•
Half of the channels are connected to the inverted input of the ASDBLR
instead of the non-inverted input.
Noise performance of the ASDBLR is better when the inverted input is left
unconnected.
NIKH EF
Proto Outer Tracker Front-End Tests
4
27/01/2004 az
Output Circuit of the ASDBLR
Resistor change from 3.9K to 1.5K
To get a voltage swing of –30mV to +30mV
Over the 120Ohm resistor
ASDBLR
NIKH EF
Low Level
Discriminator
Proto Outer Tracker Front-End Tests
5
High Level
Discriminator
27/01/2004 az
Temperatures of the Otis and ASDBLR Boards
NIKH EF
Proto Outer Tracker Front-End Tests
6
27/01/2004 az
Area of the Temperature Picture
NIKH EF
Proto Outer Tracker Front-End Tests
7
27/01/2004 az
Power
•
ASDBLR Board
– Draws 150mA from the positive supply and 110mA from the negative supply
•
OTIS Board
– Draws 320 mA from the positive supply only
•
Complete Front-end Box
– Draws 2.6 A from the positive supply (+5.3V) and 0.9 A from the negative supply (5.3V) if the the supplies are switch on simultaneously, if the supplies are switched
on sequentially, the current of the positive supply is 180 mA higher (regulator in a
different mode??)
•
The currents mentioned are typical values!
NIKH EF
Proto Outer Tracker Front-End Tests
8
27/01/2004 az
Test setup
PC
Bx-clk
Hola
L0
MVME
2600
TTCvi
TTCrx
TTCvx
Com-I2C
TFC
Analyzer
I2C
Data
Gol-Aux
NIKH EF
OS
1uSec
Step
Attenuator
Proto Outer Tracker Front-End Tests
Otis
Asd Asd
Asd Asd
Q injector
Adjustable
Delay
Otis
9
27/01/2004 az
Input Sensitivity
Sensitivety
Sensitivity
100
90
80
charge
charge (pC)
(fC)
70
60
50
channel(n)
40
30
20
10
0
0
200
400500 600
800 1000
1000
1200
1500
1400
threshold (mV)
NIKH EF
Proto Outer Tracker Front-End Tests
10
27/01/2004 az
Cross talk
Cross talk
2500
charge (fC)
2000
1500
charge channel(n-1)
charge channel(n+1)
1000
500
Caused by noise
0
0
500
1000
1500
threshold (mV)
NIKH EF
Proto Outer Tracker Front-End Tests
11
27/01/2004 az
Noise Sources
•
Via Power on the Otis board:
–
–
•
Otis read-out; the LVDS receiver is powered by the +3V that is also used for the ASDBLR.
This causes noise hits at thresholds < 750 mV. In the next version this LVDS receiver is not
needed anymore.
Bx-Clock; there is a capacitive coupling between the power to the ASDBLR boards (-3V) and
the digital power plane of the OTIS. This causes noise hits at thresholds < 600 mV. Care must
be take in the next Otis board to keep the digital power plane from the power routing to the
ASDBLR boards. Also keep outs in the GND plane are needed to keep the coupling to the
ASDBLR power as low as possible. The tests are done with an ‘open’ Front End box, the
coupling will be lower when the outer plates are mounted.
At the Input of the ASDBLR:
–
The inputs of the ASDBLR are symmetrical, so the circuit at the negative input is the same as
the positive input, this causes noise to be injected in the negative input. If the negative input is
left open the noise hits at a threshold of 550 mV goes from 35% to 1,8%. The cross talk figures
do not change when the negative input is left open.
NIKH EF
Proto Outer Tracker Front-End Tests
12
27/01/2004 az
Noise
The noise figure is determined by applying test pulses at a specific threshold
level and measure the hits at output of the ASDBLR. At a threshold of 750 mV
and a testsignal <3 fC, no hits at the output. If the test pulse is 5,8 fC every
testpulse gives a hit at the output.
This gives a noise figure of 2,8 fC.
NIKH EF
Proto Outer Tracker Front-End Tests
13
27/01/2004 az