Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Semiconductor Simulation Laboratory Phase-Locked Loop Design Phase-Locked Loops • • Phase-locked loops: Building blocks in receivers and other communication electronics Main premise: Lock in to a frequency or phase component of an incoming signal and give a synchronized output Block diagram: Phase Detector & Loop Filter: Schematic and Responses •Phase Detector: Creates an output proportional to the phase difference between its input signals, the incoming data and the feedback signal. •Loop Filter: A low pass filter; adds another pole to the feedback loop to control lock-in range and frequency. •Voltage-Controlled Oscillator: Produces a clock signal whose frequency is proportional to its input voltage. •Divide-by-N Counter: Feeds the output clock signal, its frequency divided by N, back to the PD. •Closed Loop Gain: H (s) clock K PD KVCO K F data s 1 K K K PD VCO F N Phase detector and the loop filter Transient responses for the phase detector and the loop filter VCO Current Pump and the VCO: Schematic and Responses 10-bit Counter Schematics Design Specifications •Design Goal Given a reference clock signal at 200 kHz, design a PLL whose output will oscillate in a range between 110 MHz to 130 MHz. •For the block diagram above, this requires a divide-by-N counter with N between 550 and 650. •Therefore we used a 10-bit binary downcounter. The inputs set the number it starts counting down from. The output of the VCO is the “count” signal for the counter. When the counter reaches zero, it is reloaded and sends a pulse to the phase detector. Full VCO A VCO current pump 250 VCO_f (MHz) • Circuit Operation 200 150 100 50 0.9 0.95 1 1.05 1.1 1.15 1.2 1.25 1.3 Vin (V) Phase-Locked Loop, Complete Circuit VCO current pump, current vs. Vin VCO, input voltage vs. frequency Phase-Locked Loop, Operation: Simulation Results Reference Clock and the Counter Output PD output to loop filter and loop filter output to VCO VCO outputs at the beginning of the simulation and after lock-in A High-Frequency FM Transceiver Transmitter PC Board Design FM Transceiver: Frequency-Modulation Transmitter and Receiver A FM transceiver consists both FM transmitter and FM receiver where FM stands for “frequency modulation”. Transmitter and receiver are the basic building blocks in modern wireless communication systems. A transmitter modulates the information signal and transmits the modulated signal in form of electro-magnetic wave. A receiver, on the other hand, receives this modulated signal and demodulates it in which way the original information is recovered. Frequency modulation differs from amplitude modulation by reflecting the changing of the amplitude of the information signal to the frequency domain. The superheterodyne topology is used for high frequency solution. We are working on the design and hardware implementation of a high-frequency FM transceiver. First, we try to investigate some of the design issues and thus improve the performance of the system. Second, we use this transmitter as the platform to test signal interference effects associated with the topology. Design of High-Frequency FM Transceiver Voltage Adder Input Signal DC Bias Mixer PA VCO • FM Transmitter Antenna The information signal is first added to a DC signal which enables the VCO (voltage controlled oscillator) to have the maximal operation linearity. The VCO acts as the FM modulator. The modulated signal is up-converted by the mixer to wanted carrier frequency. The PA (power amplifier) further increases the signal level which is transmitted by the antenna. Matching Network RC Network FM Modulator Local Oscillator • FM Receiver Antenna The modulated signal sent out by the transmitter is received by the antenna at the receiver end and is amplified by the LNA (low noise amplifier). The mixer down-converts this signal to intermediate frequency (IF), realizing the tuning function. The PLL (phase lock loop) demodulates the FM signal and thus the original information is recovered for processing. Mixer Matching Network LNA IFA Crystal Filter Local Oscillator Design Note • • • • • • • • DC Bias: Voltage regulator that has very low output resistance. VCO: Current Starved Ring Oscillator. Power Amplifier: Class A cascade common-emitter amplifier with emitter degeneration and resonant load. Antenna: Loop antenna with 50Ω radiant impedance. LNA: Cascode amplifier with input matching and output buffer. Mixer: Gilbert cell. Local Oscillator: Colpitts oscillator. PLL: Phase frequency detector, charge pump, loop filter, and VCO. PLL FM Demodulator PA Output Signal Receiver Chip Layout