Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Cross section (physics) wikipedia , lookup
Water pollution wikipedia , lookup
Freshwater environmental quality parameters wikipedia , lookup
Hazardous Materials Transportation Act wikipedia , lookup
Triclocarban wikipedia , lookup
VX (nerve agent) wikipedia , lookup
Material Safety Data Sheet #415 Flux-All Purpose Liquid Soldering Flux Section 1: Product Information Supplier’s Name Manufacturer’s Name Refer to supplier Address Address Refer to supplier 2300 Winston Park Dr Oakville, ON L6H 7T7 Telephone Number Telephone Number (905) 829-8780 1-800-268-4833 Chemtrec (24 hour) 1-800-424-9300 Trade Name N/A Chemical Formula: N/A Product Use Brazing Section 2: Hazardous Ingredients Hazardous Ingredient Approximate Concentration % Hydrochloric Acid Zinc Chloride Ammonium Chloride Methyl Alcohol 1 2 3 4 5.6 34.0 9.5 1.5 CAS Number 7647-01-0 7646-85-7 12125—02-9 6-7561 LC50 LD50 OSHA PEL 1-see below 2 3 4 N/A N/A N/A N/A LC50 (inhalation- rat) 4701 ppm for 30 minutes LD50 (oral-rat) 350 mg/kg LD50 (oral-rat) 1650 mg/kg LD50 (scu-mus) 9800mg/kg Page 1 of 4 81962349 Section 3: Physical Data Physical State: Liquid Odour and Appearance: Clear. Acrid. Odour Threshold(PPM): N/A Specific Gravity: 1.354 Vapour Pressure(MM): N/A Vapour Density (Air =1): N/A Evaporation Rate: <1 Boiling Point: 120-157ºC Freezing Point: N/A Solubility in Water(20): Infinite % Volatile (by Volume): 50% pH: 1.5 Coefficient of Water/Oil Distribution: N/A Section 4: Fire or Explosion Hazard Flammable: No Means of Extinction: N/A Special Firefighting Procedures: N/A Flashpoint: N/A Upper Flammable Limit (% by volume): N/A Lower Flammable Limit (% by volume): N/A Auto ignition temperature: N/A Hazardous Combustion Products: May release chloride gas in a fire. Explosion data-sensitivity to mechanical impact: N/A Explosion data-sensitivity to static discharge: N/A Section 5: Reactivity Data Chemical Stability: Yes Incompatibility to other substances: Yes If so, which ones? Cyanides (may release toxic HCN gas) and Sulfide Salts (may release toxic H2S gas) Reactivity under what conditions? May react at high temperatures Hazardous decomposition products: N/A Section 6: Toxicological Information Corrosive Product Skin Contact: Skin Absorption: Eye Contact: Inhalation: Ingestion: May cause burning and severe irritation. Will not be absorbed by the skin. Severe burning. Blurring of vision Nose, throat, and lung irritation effects with cough, discomfort and shortness of breath. Causes severe burns to mouth, tongue, throat and stomach Page 2 of 4 81962349 Exposure Limits Irritancy of Material Sensitization to Material Carcinogenity 1 mg/m3 as fume N/A N/A No Reproductive Toxicity N/A Teratogenicity Mutagenicity Toxicologically synergistic products N/A N/A N/A Section 7: Preventive Measures Personal Protective Equipment: Protective Gloves: Rubber, asbestos or neoprene gloves. Eye Protection: Safety chemical glasses and/or face shield Respiratory Protection: If work station is not ventilated, wear NIOSH approved mask. Other: N/A Engineering Controls: Good ventilation should be provided to keep fumes below exposure limits. Leak or Spill Procedure: Was area with soap and water. Rinse and dry. Handling Procedures and Equipment: N/A Waste Disposal: Dispose of in accordance with local, provincial and federal regulations. Storage Requirements: Store material in a cool, dry area away from excessive heat or cold. Rotate Stock. Special Shipping Information: Class 8. PIN 1760, Group II. Section 8: First Aid Measures Eyes: Flush immediately with water for at least 15 minutes to remove all residue. Get medical attention. Skin: Promptly wash with soap and water to remove all residue. In the event of irritation, consult a physician. Inhalation: Remove to fresh air immediately Page 3 of 4 81962349 Section 9: Preparation Information Prepared by: Techniweld (905) 829-8780 1-800-268-4833 Date Prepared: January 1, 2009 The manufacturer believes this data to be accurate and to reflect qualified expert opinion regarding current research. However, the manufacturer cannot make any express or implied warranty as to this information Page 4 of 4 81962349